DTC B1497/97 BUS IC Communication Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1497/97 | Communication line error or open |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM |
Select the Active Test, using the Techstream to generate a control command, and then check that the servo motor operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Mix Servo Targ Pulse (D) | No. 1 damper servo sub-assembly (air mix servo motor [for driver side]) pulse | Min.: 5, Max.: 104 | - |
| Air Mix Servo Targ Pulse (P) | Passenger side air mix servo motor pulse | Min.: 6, Max.: 105 | - |
| Air Outlet Servo Pulse (D) | No. 1 damper servo sub-assembly (air outlet servo motor) pulse | Min.: 9, Max.: 97 | - |
| Air Inlet Damper Targ Pulse | Air inlet damper target pulse | Min.: 7, Max.: 28 | - |
| Cool Air Bypass Pulse | Driver side cool air bypass pulse | Min.: 8, Max.: 50 | - |
| Result | Proceed to |
| One of the servo motors is malfunctioning | A |
| All of the servo motor are malfunctioning | B |
|
| ||||
| A | |
| 2.SYSTEM CHECK |
According to the test, proceed to the next step.
| Result | Proceed to |
| Only the No. 1 damper servo sub-assembly (air mix servo motor [for driver side]) is malfunctioning | A |
| Only the air mix servo motor (for passenger side) is malfunctioning | B |
| Only the No. 1 damper servo sub-assembly (air outlet servo motor) is malfunctioning | C |
| Only the air inlet servo motor is malfunctioning | D |
| Only the cool air bypass servo motor is malfunctioning | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR [FOR DRIVER SIDE]) |
Replace the No. 1 damper servo sub-assembly (air mix servo motor [for driver side]) (Click here ).
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK AIR MIX SERVO MOTOR (FOR PASSENGER SIDE) |
Replace the air mix servo motor (for passenger side) (Click here).
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET SERVO MOTOR) |
Replace the No. 1 damper servo sub-assembly (air outlet servo motor) (Click here).
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 6.CHECK AIR INLET SERVO MOTOR |
Replace the air inlet servo motor (Click here).
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 7.CHECK COOL AIR BYPASS SERVO MOTOR |
Replace the cool air bypass servo motor (Click here).
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK AIR CONDITIONING HARNESS |
Replace the air conditioning harness.
Check for DTC (Click here).
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J19-21 (B) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | ||
| ||