Home › BODY › INTERIOR › ROOF HEADLINING (for CrewMax)

ROOF HEADLINING (for CrewMax) > REMOVAL

for Preparation Click here



1. LOWER BACK WINDOW GLASS

HINT:
Make sure to completely lower the back window glass so that the roof headlining can be removed from the rear of the vehicle.



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
(Click here)


5. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
(Click here)


6. REMOVE FRONT SEAT ASSEMBLY (for Center Seat)
(Click here)


7. REMOVE REAR SEAT ASSEMBLY (for LH Side)
(Click here)


8. REMOVE REAR SEAT ASSEMBLY (for RH Side)
(Click here)


9. REMOVE FRONT DOOR SCUFF PLATE LH


B165841
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.



10. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



11. REMOVE REAR DOOR SCUFF PLATE LH


B169218
  1. Detach the 8 claws and 2 clips, and remove the rear door scuff plate LH.



12. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



13. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the nut.

  1. Detach the 2 clips and remove the cowl side trim board LH.



14. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



19. REMOVE FRONT PILLAR GARNISH LH


    B355361E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B355363
  1. Remove the bolt.

  1. Detach the clip and remove the front pillar garnish LH.



  1. Protect the curtain shield airbag assembly.



      B165709E07
    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.

      Text in Illustration 
      *1
      Adhesive Tape
      *2
      Protective Cover
      *3
      Curtain Shield Airbag Assembly



20. REMOVE FRONT PILLAR GARNISH RH


    B355364E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



    B355366
  1. Remove the 2 bolts and front assist grip sub-assembly from the front pillar garnish RH.



    B355367
  1. Detach the clip and remove the front pillar garnish RH.

  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



21. REMOVE LOWER CENTER PILLAR GARNISH LH


B165827
  1. Detach the 2 claws and remove the cover.



    B165828
  1. Loosen the bolt and disconnect the front seat outer belt assembly LH.



    B165829
  1. Detach the 7 clips and 2 claws, and remove the lower center pillar garnish LH.



22. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



23. REMOVE CENTER PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and rear assist grip assembly from the center pillar garnish LH.

  1. Remove the bolt.



  1. Detach the clip, guide and remove the center pillar garnish LH.


    B355479E01


    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Pass the front seat outer belt assembly LH through the hole of the center pillar garnish LH.



24. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



25. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B165848
  1. Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.



26. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



27. REMOVE NO. 1 BOX SPEAKER ASSEMBLY (w/ Woofer)


    B355077
  1. Remove the 3 bolts.



    B355078
  1. Disconnect the connector and remove the No. 1 box speaker assembly.



28. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH


    B165830
  1. Detach the 2 claws and remove the cover.



    B165831
  1. Loosen the bolt and disconnect the rear seat outer belt assembly.



    B355495
  1. Detach the 5 clips and remove the lower quarter trim panel assembly LH.



29. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



30. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH


    B355496E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B355498
  1. Remove the 2 bolts.

  1. Detach the 4 clips and remove the front quarter trim panel assembly LH.

  1. Pass the rear seat outer belt assembly through the hole of the front quarter trim panel assembly LH.



31. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



32. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B169214
  1. Detach the 4 claws of the rear shoulder belt anchor plate sub-assembly LH, and slide the rear shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.



33. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



34. REMOVE ROOF CONSOLE BOX ASSEMBLY


    B356939E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 8 claws and remove the roof console box base.

    HINT:
    Tape the screwdriver tip before use.



    B356941
  1. Using a T20 "TORX" driver, remove the 4 "TORX" screws and remove the roof console box assembly.

  1. Disconnect the connector.



35. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227021
  1. Slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to detach the 2 claws from the roof headlining, and then detach the 2 claws of the inner rear view mirror stay holder cover from the mirror and remove the inner rear view mirror stay holder cover.



36. REMOVE ROOM LIGHT ASSEMBLY


E281382E01
  1. Using a screwdriver, detach the 4 claws and 2 guides and remove the No. 1 room light lens.
    Text in Illustration 
    *1
    Tape



    E281383
  1. Detach the 2 clips and 3 guides and remove the No. 1 room light assembly.



37. REMOVE VISOR ASSEMBLY LH


B355481
  1. Remove the 2 screws.

  1. Detach the claw and remove the visor assembly LH.



    B355482
  1. w/ Vanity Light:
    Disconnect the connector.



38. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



39. REMOVE VISOR HOLDER

HINT:
Use the same procedure to remove the visor holder on the other side.



    B165713
  1. Using a T20 "TORX" driver, remove the "TORX" screw and visor holder.



40. REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for all the assist grip sub-assemblies.



    B155751E10
  1. Using a screwdriver, detach the 2 claws and remove the assist grip cover.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure to remove the assist grip cover on the other side.

    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 2 clips and remove the assist grip sub-assembly.



41. REMOVE ROOF HEADLINING ASSEMBLY


    B167283
  1. w/ EC Mirror:
    Disconnect the connector.



    B191401
  1. w/ Sliding Roof:
    Disconnect the connector.



    B355487
  1. Disconnect the connector and detach the 4 wire harness clamps from the front pillar LH.

  1. w/o Sliding Roof:
    Detach the 4 clips and remove the roof headlining assembly.



  1. w/ Sliding Roof:
    Detach the 4 clips and 12 fasteners, and remove the roof headlining assembly.


    B355499E01


    Text in Illustration 
    *A
    w/o Sliding Roof
    *2
    w/ Sliding Roof



    B355500
  1. Take out the roof headlining assembly from the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining assembly when taking it out.