Home › TRANSMISSION ยท AB60F AUTOMATIC TRANSMISSION › TRANSMISSION CONTROL CABLE (for Column Shift Type)

TRANSMISSION CONTROL CABLE (for Column Shift Type) > INSTALLATION

for Preparation Click here



1. INSTALL COLUMN SHIFT TRANSMISSION CONTROL CABLE ASSEMBLY


C157286
  1. Insert the column shift transmission control cable from the vehicle interior, and install the cable retainer with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    C158378
  1. Connect the cable to the steering column shaft bracket so that the outer cable socket's claws attach securely.



    C158379E01
  1. Connect the column shift transmission control cable end to the column shift.

    NOTICE:
    Make sure to install the cable end so that the inner cable is not twisted. Confirm that the cable end's ridged side is facing upward.



    C157289
  1. Connect the 2 cable clamps with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Return the floor carpet front LH side to its original position.

  1. Move the shift lever to the N position.



    C155873E01
  1. Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.



    C158380E01
  1. Connect the control cable with a new clip and the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the inside of the vehicle.



    C157285
  1. Connect the transmission control cable support with the nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL FRONT SEAT ASSEMBLY LH
  1. for Power Seat Type:
    Install the front seat LH (Click here).

  1. for Manual Seat Type:
    Install the front seat LH (Click here).



3. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



4. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



5. INSTALL UPPER STEERING COLUMN COVER


    C290068
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



6. INSTALL LOWER STEERING COLUMN COVER


    C290067
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



7. INSTALL CENTER LOWER INSTRUMENT COVER
  1. Attach the 2 guides and 2 clips to install the lower center instrument cover.

  1. Install the 2 clips.



8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


  1. Connect the hood lock control cable to the hood lock control lever, rotate the hood lock control cable, and then slide and push the hood lock control cable into place.


    B355340

  1. Attach the 3 hooks to connect the hood lock control lever to the lower instrument panel finish panel sub-assembly LH.

  1. Connect each connector.



    B355338
  1. Attach the 9 clips and 2 claws to install the lower instrument panel finish panel sub-assembly LH.

  1. Install the 2 bolts <A>.



10. INSTALL COWL SIDE TRIM BOARD LH
  1. Attach the 2 clips to install the cowl side trim board LH.

  1. Install the nut.



11. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)
  1. Attach the 6 claws and 3 clips to install the front door scuff plate LH.



12. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)
  1. Attach the 6 claws and 3 clips to install the front door scuff plate LH.



13. INSTALL STEERING WHEEL ASSEMBLY
(Click here)