Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The combination meter receives vehicle speed signals from the skid control ECU via the CAN line. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

WIRING DIAGRAM


E140490E56


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system DTC is output
    B



B
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK SFI SYSTEM (VEHICLE SPEED)
  1. Check if a SFI system DTC is output.

    1. for 1GR-FE (Click here)
    2. for 1UR-FE (Click here)
    3. for 3UR-FE (Click here)
    4. for 3UR-FBE (Click here)
    Result 
    Result
    Proceed to
    SFI system DTC is not output
    A
    SFI system (for 1GR-FE) DTC is output
    B
    SFI system (for 1UR-FE) DTC is output
    C
    SFI system (for 3UR-FE) DTC is output
    D
    SFI system (for 3UR-FBE) DTC is output
    E



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

D
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

E
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (SPEEDOMETER)
  1. Operate the Techstream according to the display and select "Active Test" (Click here).

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160 or 200
    Acceptable range (km/h or mph): [Control range → Speedometer display]
    for mph
    1. 40 mph → 39 to 42.5 mph
    2. 80 mph → 79.5 to 84 mph
    3. 120 mph → 120 to 125.5 mph
    for km/h
    1. 40 km/h → 41.7 to 46.2 km/h
    2. 80 km/h → 83.4 to 88.4 km/h
    3. 120 km/h → 125.1 to 130.6 km/h
    4. 160 km/h → 166.2 to 173.2 km/h
    5. 200 km/h → 207.7 to 215.7 km/h

    OK:
    Needle indication is normal.

    HINT:
    1. Confirm that the vehicle is stopped and engine is idling. It is normal that door will be locked automatically when performing the speedometer Active Test.
    2. The displayed value has the same units (km/h, mph) as the main scale of the vehicle's speedometer.
    3. The needle position should be within the acceptable tolerance.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
  1. Operate the Techstream according to the display and select "Data List" (Click here).

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 (0), Max.: 255 (158)
    Almost same as actual speed (when driving)
    Unit: km/h (mph)

    OK:
    Vehicle speed displayed on Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.READ VALUE USING TECHSTREAM (WHEEL SPEED SENSOR)
  1. Operate the Techstream according to the display and select "Data List" (Click here).

    ABS/VSC/TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (FL/FR/RL/RR) Wheel Speed
    Wheel speed sensor (FL/FR/RL/RR) reading/Min.: 0 (0), Max.: 326 (202)
    Actual wheel speed
    Similar speed as indicated on speedometer

    OK:
    Vehicle speed displayed on Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).



NG
REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)