Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > Sliding Roof Control Switch Circuit

for Preparation Click here


DESCRIPTION

If either the sliding function or tilt function does not operate, there may be a malfunction in the sliding roof switch circuit.

WIRING DIAGRAM


B167040E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SLIDING ROOF OPERATION)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof operates (Click here).

    Sliding Roof 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof SLIDE CLOSE/TILT UP or SLIDE OPEN/TILT DOWN
    Clos/Up: Sliding roof SLIDE CLOSE or TILT UP operation occurs
    Opn/Dwn: Sliding roof SLIDE OPEN or TILT DOWN operation occurs
    OFF: Sliding roof is not operating
    -

    OK:
    Sliding roof operates normally.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)
OK


2.READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH)
  1. Use the Data List to check if the sliding roof switch is functioning properly (Click here).

    Sliding Roof 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Open Switch
    Sliding roof open switch signal/ON or OFF
    ON: SLIDE switch is pressed to open
    OFF: SLIDE switch is not pressed to open
    -
    Close Switch
    Sliding roof close switch signal/ON or OFF
    ON: SLIDE switch is pressed to close
    OFF: SLIDE switch is not pressed to close
    -
    Up Switch
    Sliding roof up switch signal/ON or OFF
    ON: TILT switch is pressed to up
    OFF: TILT switch is not pressed to up
    -
    Down Switch
    Sliding roof down switch signal/ON or OFF
    ON: TILT switch is pressed to down
    OFF: TILT switch is not pressed to down
    -

    OK:
    The Techstream displays as shown in the table according to the operation of each switch.



NG
Go to step 3
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)  

3.INSPECT SLIDING ROOF SWITCH
B167041E02
  1. Remove the sliding roof switch .

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UP) - 5 (E)
    TILT switch is pressed to up
    Below 1 Ω
    1 (UP) - 5 (E)
    TILT switch is not pressed to up
    10 kΩ or higher
    2 (DWN) - 5 (E)
    TILT switch is pressed to down
    Below 1 Ω
    2 (DWN) - 5 (E)
    TILT switch is not pressed to down
    10 kΩ or higher
    4 (OPN) - 5 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    4 (OPN) - 5 (E)
    SLIDE switch is not pressed to open
    10 kΩ or higher
    3 (CLS) - 5 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    3 (CLS) - 5 (E)
    SLIDE switch is not pressed to close
    10 kΩ or higher



NG
REPLACE SLIDING ROOF SWITCH (Click here)
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY
E146741E05
  1. Remove the roof console box with sliding roof switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 7 (E)
    TILT switch is pressed to up
    Below 1 Ω
    6 (UP) - 7 (E)
    TILT switch is not pressed to up
    10 kΩ or higher
    5 (DWN) - 7 (E)
    TILT switch is pressed to down
    Below 1 Ω
    5 (DWN) - 7 (E)
    TILT switch is not pressed to down
    10 kΩ or higher
    4 (OPN) - 7 (E)
    SLIDE switch is pressed to open
    Below 1 Ω
    4 (OPN) - 7 (E)
    SLIDE switch is not pressed to open
    10 kΩ or higher
    3 (CLS) - 7 (E)
    SLIDE switch is pressed to close
    Below 1 Ω
    3 (CLS) - 7 (E)
    SLIDE switch is not pressed to close
    10 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)


    B171201E01
  1. Disconnect the W3 ECU connector.

  1. Disconnect the W7 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-1 (UP) - W7-6 (UP)
    Always
    Below 1 Ω
    W3-2 (DWN) - W7-5 (DWN)
    Always
    Below 1 Ω
    W3-6 (OPN) - W7-4 (OPN)
    Always
    Below 1 Ω
    W3-7 (CLS) - W7-3 (CLS)
    Always
    Below 1 Ω
    W7-6 (UP) - Body ground
    Always
    10 kΩ or higher
    W7-5 (DWN) - Body ground
    Always
    10 kΩ or higher
    W7-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    W7-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    W7-7 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)