Home › ENGINE · 1UR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


4. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Remove the front wiper motor and link (Click here).



5. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    A215892E01

  1. Tighten the radiator drain cock plug by hand.



8. REMOVE HOOD SUB-ASSEMBLY


    A302499
  1. Using a screwdriver, release the 2 clips and remove the 2 hood supports assembly.

    HINT:
    Tape the screwdriver tip before use.

    CAUTION:
    Remove the hood support assembly while supporting the hood by hand.

  1. Remove the 4 bolts and hood.



9. REMOVE V-BANK COVER SUB-ASSEMBLY


    A214822E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



10. REMOVE AIR CLEANER HOSE ASSEMBLY


    A214569
  1. Disconnect the vacuum sensing hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



11. REMOVE AIR CLEANER ASSEMBLY


    A309637E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. for Type A:
      Unfasten the 4 hook clamps and then remove the air cleaner cap.

    4. for Type B:
      Unfasten the 2 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A309638E01
  1. Remove the 2 bolts and air cleaner case.



12. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose and detach the 2 wire harness clamps.



  1. Remove the 7 bolts and cowl top outer panel sub-assembly.


    A215877



13. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and fender apron seal.



14. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and fender apron seal.



15. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and fender apron seal.



16. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



17. REMOVE INLET RADIATOR HOSE


    A215577
  1. Remove the radiator hose.



18. DISCONNECT OUTLET RADIATOR HOSE


    A215882
  1. Disconnect the radiator hose.



19. REMOVE RADIATOR GRILLE SUB-ASSEMBLY


    B353342E01
  1. Put protective tape around the radiator grille sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 4 screws and 2 clips.



    B353345
  1. Detach the 4 claws and 3 clips and remove the radiator grille sub-assembly.



20. REMOVE RADIATOR SIDE DEFLECTOR RH


    A299482
  1. Using a clip remover, remove the 3 clips and disconnect the radiator side deflector RH.



21. REMOVE RADIATOR SIDE DEFLECTOR LH


    A299483
  1. Using a clip remover, remove the 3 clips and disconnect the radiator side deflector LH.



22. REMOVE FAN AND GENERATOR V BELT


    A163770E01
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



23. REMOVE FAN SHROUD


    A217580
  1. Loosen the 4 nuts holding the fluid coupling fan

  1. Remove the fan and generator V-belt (Click here).

  1. Disconnect the reservoir hose from the upper radiator tank.



    A151821
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



24. REMOVE RADIATOR ASSEMBLY


    A299479
  1. Remove the 4 bolts and radiator assembly.



    A183240
  1. Slide the clamp and remove the outlet radiator hose from the radiator assembly.

  1. Remove the radiator drain cock plug from the radiator assembly.

  1. Remove the O-ring from the radiator drain cock plug.



25. DISCONNECT NO. 12 WATER BY-PASS HOSE


    A214277
  1. Disconnect the No. 12 water by-pass hose.



26. DISCONNECT NO. 13 WATER BY-PASS HOSE


    A217531
  1. Disconnect the No. 13 water by-pass hose.



27. REMOVE EGR VALVE ASSEMBLY


    A214280
  1. Disconnect the 3 clamps and connector.



    A214279
  1. Remove the 4 nuts.



    A214281
  1. Remove the 2 bolts and EGR valve.



    A214876
  1. Remove the gasket from the No. 2 EGR pipe.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



    A214282
  1. Remove the gasket from the intake manifold.



28. REMOVE EGR VALVE BRACKET


    A214283
  1. Remove the 3 bolts and EGR valve bracket.



29. REMOVE VENTILATION HOSE ASSEMBLY


    A215286
  1. Slide the 2 clamps and disconnect the ventilation hose assembly from the ventilation pipe of the cylinder head cover sub-assembly LH and cylinder head cover sub-assembly RH.

  1. Remove the bolt and ventilation hose assembly.



30. REMOVE AIR TUBE SUB-ASSEMBLY LH


    A215879
  1. Disconnect the 2 connectors.

  1. Disconnect the water by-pass hose.



    A215282
  1. Disconnect the 2 wire harness clamps and air hose.

  1. Remove the bolt and disconnect the air tube LH from the water inlet housing.



    A215284
  1. Disconnect the vacuum sensor connector and clamp.

  1. Remove the 2 bolts and disconnect the air hose from the air switching valve LH.

  1. Remove the air tube LH.



31. REMOVE INTAKE MANIFOLD


    A307762
  1. Disconnect the throttle body connector from the throttle body assembly.

  1. Slide the clamp and disconnect the No. 4 water by-pass hose from the front water by-pass joint.

  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A215287
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A215288
  1. Slide the clamp and disconnect the vacuum hose from the union to connector tube hose assembly.



    A215285
  1. Remove the bolt.

  1. Detach the 3 engine wire harness clamps from the 3 wire harness brackets.



    A307793
  1. Detach the 4 clamps from the fuel tube sub-assembly.



    A214311
  1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly RH (Click here).



    A214312
  1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly LH (Click here).



    A215289
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



32. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A308865
  1. Remove the fuel pipe clamp.

  1. Disconnect the No. 1 fuel pipe (Click here).



33. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
  1. Disconnect the No. 2 fuel tube (Click here).



34. DISCONNECT WIRE HARNESS AND HOSE


    A214862
  1. Disconnect the clamp and ECM connector.

    HINT:
    Refer to the following procedures to disconnect the ECM connector .



    A214858
  1. Disconnect the No. 4 water by-pass hose.



    A214851
  1. Disconnect the 2 heater hoses.



    A160782E01
  1. Disconnect the 4 connectors from the connector holder block.



    A214573
  1. Remove the bolt and disconnect the clamp and ground wire.

  1. Disconnect the air pump connector and 2 clamps.

  1. Remove the nut and connector bracket.

  1. Disconnect the air injection system hose.



    A163790
  1. Remove the nut and disconnect the wire from the positive (+) battery cable.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the 4 air injection control driver connectors.

  1. Remove the nut and disconnect the wire and 2 clips from the engine room junction block.

  1. Disconnect the 2 connectors and 2 clips from the engine room junction block.



35. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



36. DISCONNECT VANE PUMP ASSEMBLY


    A163289
  1. Remove the 2 bolts and disconnect the vane pump assembly.



37. REMOVE GENERATOR ASSEMBLY


    A215539
  1. Remove the terminal cap.

  1. Disconnect the generator connector.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A216790
  1. Remove the 3 bolts, nut and generator.



38. REMOVE PROPELLER SHAFT ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



39. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
  1. Remove the front propeller shaft (Click here).



40. REMOVE EXHAUST PIPE ASSEMBLY
  1. Remove the exhaust pipe assembly (Click here).



41. DISCONNECT NO. 1 WATER BY-PASS PIPE


    A214575
  1. Remove the 3 bolts and disconnect the No. 1 water by-pass pipe.



42. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A216301
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from dipstick guide.



43. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY


    A214293
  1. Remove the 4 nuts and EGR pipe.

  1. Remove the 2 gaskets.



44. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A215348
  1. Remove the 3 bolts and heat insulator.



45. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A215349
  1. Remove the 9 nuts, exhaust manifold and 2 gaskets.



46. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A215350
  1. Remove the 3 bolts and heat insulator.



47. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A215351
  1. Remove the 9 nuts, exhaust manifold and 2 gaskets.



48. REMOVE STARTER COVER


    A215551
  1. Remove the 3 bolts and starter cover.



49. REMOVE STARTER ASSEMBLY


    A258285
  1. Detach the 2 wire harness clamps.

  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.



    A258286
  1. Remove the 2 bolts and starter.



    A215546
  1. Remove the flywheel housing side cover.



50. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



51. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)


C155909
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



52. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)


C157037
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



53. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A163778E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  



    A214574
  1. Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.



54. REMOVE ENGINE ASSEMBLY


    A308809
  1. Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    Engine hanger
    12281-38150
    Bolt
    90119-A0166

  1. Attach an engine sling device and hang the engine with a chain block.



    A214577E01
  1. Remove the 4 engine mounting insulator bolts.

  1. Lift the engine out from the vehicle slowly and carefully.

    NOTICE:
    Make sure the engine is clear of all wiring, hoses and cables.



55. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.