Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1AB4    Open in Outer Mirror Indicator(Master)

for Preparation Click here


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the blind spot monitor indicator RH.

DTC Code
DTC Detection Condition
Trouble Area
C1AB4
With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
  1. Harness or connector
  2. Outer rear view mirror sub-assembly RH
  3. Outer rear view mirror assembly RH
  4. Blind spot monitor sensor RH

WIRING DIAGRAM


E221720E10


INSPECTION PROCEDURE

NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
  1. Disconnect the S6 blind spot monitor sensor RH connector.

  1. Disconnect the M6 outer rear view mirror assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Memory:
    Tester Connection
    Condition
    Specified Condition
    S6-4 (OMIR) - M6-9 (BSR+)
    Always
    Below 1 Ω
    M6-5 (MLP-) - Body ground
    Always
    Below 1 Ω
    w/o Memory:
    Tester Connection
    Condition
    Specified Condition
    S6-4 (OMIR) - M6-18 (BSR+)
    Always
    Below 1 Ω
    M6-5 (MLP-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    E231117E03
  1. Remove the outer rear view mirror assembly RH (Click here).

  1. Remove the outer rear view mirror sub-assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Memory:
    Tester Connection
    Condition
    Specified Condition
    M6-9 (BSR+) - A-7 (+)
    Always
    Below 1 Ω
    M6-5 (MLP-) - A-5 (-)
    Always
    Below 1 Ω
    w/o Memory:
    Tester Connection
    Condition
    Specified Condition
    M6-18 (BSR+) - A-7 (+)
    Always
    Below 1 Ω
    M6-5 (MLP-) - A-5 (-)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/ Memory
    *B
    w/o Memory
    *a
    Vehicle Side
    *b
    Outer Rear View Mirror Sub-assembly RH Side



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)
OK


4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH
  1. Replace the outer rear view mirror sub-assembly RH with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)
OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH IS DEFECTIVE)