Home › DRIVE LINE › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

DTC    P17A5    Transfer Synchronization Actuator Circuit Open

DTC    P17A6    Transfer Synchronization Actuator Circuit Low

for Preparation Click here


DESCRIPTION

This DTC is detected when an open circuit or short to ground is detected in the solenoid coil drive circuit.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P17A5
  1. Ignition switch ON (when not switching between 2WD and 4H)
  2. Open circuit in the solenoid coil drive circuit
  3. 1 second or more
  4. 1 trip detection logic
  1. Wire harness and connector
  2. 4 wheel drive control ECU
  3. Solenoid coil sub-assembly
  4. Transfer shift actuator assembly
P17A6
  1. Ignition switch ON (when switching between 2WD and 4H)
  2. Short to ground in the solenoid coil drive circuit
  3. 0.1 seconds or more
  4. 1 trip detection logic
  1. Wire harness and connector
  2. 4 wheel drive control ECU
  3. Solenoid coil sub-assembly
  4. Transfer shift actuator assembly

WIRING DIAGRAM


C290927E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
  1. Disconnect the A26 4 wheel drive control ECU connector.

  1. Disconnect the D67 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-6 (SCC) - D67-3 (SCC)
    Always
    Below 1 Ω
    A26-6 (SCC) or D67-3 (SCC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (SCC TERMINAL)
C291017E01
  1. Disconnect the D67 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    DTC P17A5 is output 
    Tester Connection
    Condition
    Specified Condition
    3 (SCC) - Body ground
    Always
    Below 5 Ω
    DTC P17A6 is output 
    Tester Connection
    Condition
    Specified Condition
    3 (SCC) - Body ground
    Always
    1 Ω or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transfer Shift Actuator Assembly)



NG
Go to step 3
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)  

3.INSPECT SOLENOID COIL SUB-ASSEMBLY
C295407E01
  1. Disconnect the A solenoid coil sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    DTC P17A5 is output 
    Tester Connection
    Condition
    Specified Condition
    2 - Body ground
    Always
    Below 5 Ω
    DTC P17A6 is output 
    Tester Connection
    Condition
    Specified Condition
    2 - Body ground
    Always
    1 Ω or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Solenoid Coil Sub-assembly)



NG
REPLACE SOLENOID COIL SUB-ASSEMBLY (Click here)
OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY (Click here)