Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › THROTTLE BODY
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233891 THROTTLE BODY A

1UR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the throttle body assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A215428E01
1.248,2.255 2.022,2.404 0.774,0.149 10 White Paint 1.192,2.346 1.106,2.346 1.106,2.346 0.93,2.718 false 0.11,0.516 0.884,0.665 0.774,0.149 10 White Paint 1.076,0.611 1.133,0.611 1.133,0.611 1.23,1.086 false

Install the No. 4 water by-pass hose to the throttle body.

HINT:

When installing the hose, make sure the paint mark and clip are as shown in the illustration.



b.
A215427E01
2.057,1.253 2.831,1.399 0.774,0.147 10 Green Paint 2.004,1.339 1.924,1.339 1.924,1.339 1.57,0.903 false 2.217,1.76 2.991,1.906 0.774,0.147 10 Green Paint 2.164,1.837 2.044,1.837 2.044,1.837 1.018,2.038 false

Install the No. 12 water by-pass hose to the throttle body.

HINT:

When installing the hose, make sure the paint mark and clip are as shown in the illustration.



c.
A218982E02
2.365,0.156 2.302,0.156 2.302,0.156 1.729,0.427 false 1.521,0.833 1.583,0.833 1.583,0.833 2.323,1.021 false 2.396,0.073 2.917,0.406 0.521,0.333 10 true Groove 0.802,0.75 1.49,1.073 0.688,0.323 10 true Protrution

Install a new gasket to the intake air surge tank.

HINT:

Align the protrusion of the gasket with the groove of the intake air surge tank.



d.
A215292

Install the throttle body with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.
A215424E02
2.292,0.865 2.458,1.208 2.458,1.208 2.479,1.208 false 1.573,0.094 1.719,0.094 1.719,0.094 2.469,0.604 false 0.969,0.698 1.104,0.698 1.104,0.698 1.969,0.865 false 1.396,4.125 1.625,4.125 false 1.625,4.125 2.635,3.74 false 2.563,1.094 3.229,1.448 0.667,0.354 10 true 5 mm (0.197 in.) 0.135,0.021 1.552,0.396 1.417,0.375 10 false 13 to 17 mm (0.511 to 0.669 in.) 0.24,0.625 0.938,0.802 0.698,0.177 10 false Blue Paint 0.552,4.031 1.385,4.198 0.833,0.167 10 false Yellow Paint

Connect the throttle position sensor and control motor connector.


f.

Connect the 2 water by-pass hoses.

HINT:

When connecting the hoses, make sure the paint marks and clips are as shown in the illustration.



Hide 7.PERFORM INITIALIZATION

NOTICE:

Perform the following procedure after replacing the throttle body assembly or any throttle body assembly components. The following procedure should also be performed if the throttle body assembly is cleaned.


a.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above step again.



b.

Connect the Techstream to the DLC3 and clear the DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


c.

Perform the "Inspection After Repairs" (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


d.

Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Standard:
Condition Engine Idle Speed
A/C switched off 650 to 750 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or neutral.




e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.


f.

Perform a road test and confirm that there are no abnormalities.