Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the ECT, is built into the Engine Coolant Temperature (ECT) sensor.

The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in ECT sensor circuit

·

ECT sensor

·

ECM


P0117 Short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in ECT sensor circuit

·

ECT sensor

·

ECM


P0118 Open in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in ECT sensor circuit

·

ECT sensor

·

ECM



HINT:

When any of these DTCs are stored, check the ECT by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

MONITOR DESCRIPTION

The Engine Coolant Temperature (ECT) sensor is used to monitor the ECT. The ECT sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the ECT sensor and stores a DTC.

Example:

If the sensor output voltage is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the ECT sensor circuit, and stores DTC P0118. Conversely, if the voltage output is less than 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0117.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P0115: ECT sensor range check (Fluctuating)
P0117: ECT sensor range check (Low voltage)
P0118: ECT sensor range check (High voltage)
Required Sensors/Components (Main) ECT sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None

TYPICAL MALFUNCTION THRESHOLDS

P0115
ECT sensor voltage Less than 0.14 V, or more than 4.91 V [More than 135°C (275°F), or less than -60°C (-76°F)]

P0117
ECT sensor voltage [ECT] Less than 0.14 V [More than 135°C (275°F)]

P0118
ECT sensor voltage [ECT] More than 4.91 V [Less than -60°C (-76°F)]

COMPONENT OPERATING RANGE

ECT sensor voltage [ECT] 0.14 to 4.91 V [-60 to 135°C (-76 to 275°F)]

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0115, P0117 or P0118.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162760E26
0.316,1.838 0.631,2.001 0.316,0.163 10 D28 0.317,1.981 2.634,2.151 2.318,0.170 10 Engine Coolant Temperature Sensor 2.421,1.246 2.542,1.409 0.121,0.163 10 1 2.435,0.63 2.556,0.793 0.121,0.163 10 2 5.955,2.247 6.243,2.417 0.288,0.170 10 D74 5.285,0.634 5.469,0.787 0.184,0.152 10 76 5.285,1.257 5.469,1.410 0.184,0.152 10 98 5.511,0.631 5.878,0.773 0.367,0.142 10 THW 5.523,1.254 5.730,1.396 0.207,0.142 10 E2 5.953,2.386 6.317,2.559 0.364,0.173 10 ECM 6.24,0.261 6.507,0.424 0.267,0.163 10 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING TECHSTREAM (ENGINE COOLANT TEMPERATURE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value displayed on the Techstream.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Between 75 and 100°C (167 and 212°F) C

HINT:
·

If there is an open circuit, the Techstream indicates -40°C (-40°F).


·

If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.





A

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
U151667E02
0.354,1.375 1.146,1.531 0.792,0.156 10 false ECT Sensor 1.448,0.417 1.76,0.583 0.313,0.167 10 false D28 0.698,3.365 1.01,3.531 0.313,0.167 10 false D28 1.719,0.76 1.833,0.927 0.115,0.167 10 false 2 1.708,1.146 1.844,1.333 0.135,0.188 10 false 1 2.427,0.75 2.865,0.938 0.438,0.188 10 false THW 2.427,1.219 2.667,1.385 0.24,0.167 10 false E2 2.531,1.469 2.969,1.646 0.438,0.177 10 false ECM 0.125,2.094 2.479,2.448 2.354,0.354 10 false Front view of wire harness connector: (to ECT sensor)

a.

Disconnect the ECT sensor connector.


b.

Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value displayed on the Techstream.

Standard value:

140°C (284°F) or higher


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A379417E01
0.75,1.615 1.177,1.844 0.427,0.229 3.698,0.875 4.125,1.104 0.427,0.229 4.781,1.792 5.177,2.302 false 4.719,1.865 4.375,2.292 false 0.51,0.167 2.823,0.573 2.313,0.406 10 false Front view of wire harness connector: (to ECT Sensor) 3.76,0.156 6.073,0.563 2.313,0.406 10 false Front view of wire harness connector: (to ECM) 0.844,1.656 1.167,1.854 0.323,0.198 10 false D28 3.792,0.906 4.115,1.104 0.323,0.198 10 false D74 4.24,2.313 4.563,2.51 0.323,0.198 10 false E2 5.156,2.323 5.583,2.521 0.427,0.198 10 false THW

a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D28-2 - D74-76 (THW) Always Below 1 Ω
D28-1 - D74-98 (E2) Always Below 1 Ω




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
U151552E02
1.458,0.75 1.76,0.906 0.302,0.156 10 false D28 0.438,1.688 1.302,1.885 0.865,0.198 10 false ECT Sensor 2.521,1.729 2.948,1.927 0.427,0.198 10 false ECM 2.469,1.51 2.688,1.677 0.219,0.167 10 false E2 2.469,1.063 2.833,1.229 0.365,0.167 10 false THW

a.

Disconnect the ECT sensor connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value displayed on the Techstream.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A379417E02
0.708,1.542 1.125,1.802 0.417,0.26 3.635,0.885 4.052,1.146 0.417,0.26 4.781,1.792 5.125,2.354 false 0.542,0.135 2.844,0.5 2.302,0.365 10 false Front view of wire harness connector: (to ECT Sensor) 3.76,0.135 6.063,0.5 2.302,0.365 10 false Front view of wire harness connector: (to ECM) 0.792,1.594 1.135,1.802 0.344,0.208 10 false D28 3.719,0.938 4.063,1.146 0.344,0.208 10 false D74 5.167,2.344 5.531,2.552 0.365,0.208 10 false THW

a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D28-2 or D74-76 (THW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR