Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal conditions are as shown in the table below.

Signal
(ECM Terminal)
Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the Techstream, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



WIRING DIAGRAM

A164732E05
6.068,3.172 6.426,3.328 0.357,0.156 10 ECM 5.676,0.799 6.027,0.969 0.350,0.170 10 ST1- 5.68,1.554 5.989,1.710 0.309,0.156 10 STP 5.452,0.805 5.636,0.961 0.184,0.156 10 35 6.081,3.036 6.376,3.192 0.295,0.156 10 A24 5.458,1.551 5.642,1.707 0.184,0.156 10 36 4.191,1.942 4.403,2.112 0.211,0.170 10 A4 4.191,2.075 5.312,2.238 1.121,0.163 10 Stop Light Switch 5.085,0.786 5.241,0.949 0.156,0.163 10 3 5.088,1.542 5.202,1.712 0.114,0.170 10 1 4.289,0.793 4.439,0.956 0.149,0.163 10 4 4.285,1.55 4.392,1.713 0.107,0.163 10 2 3.645,1.009 3.926,1.165 0.281,0.156 10 IGN 3.789,1.766 4.209,1.922 0.420,0.156 10 STOP 2.601,1.808 2.882,1.964 0.281,0.156 10 IG2 1.844,1.374 2.125,1.530 0.281,0.156 10 IG2 2.188,1.374 2.295,1.537 0.107,0.163 10 6 1.081,1.374 1.188,1.537 0.107,0.163 10 5 1.249,1.374 1.571,1.530 0.323,0.156 10 AM2 1.025,2.354 1.347,2.510 0.323,0.156 10 AM2 0.478,2.27 0.870,2.607 0.392,0.336 10 IG2 MAIN 3.69,3.643 3.978,3.799 0.288,0.156 10 ALT 0.646,4.792 1.136,4.976 0.489,0.184 10 Battery 1.382,1.883 1.561,2.039 0.179,0.156 10 J9 1.382,2.023 2.311,2.202 0.929,0.179 10 Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the Techstream.

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
U151424E02
0.177,0.125 2.521,0.469 2.344,0.344 10 false Front view of wire harness connector: (to Stop Light Switch) 0.865,1.792 1.135,1.969 0.271,0.177 10 false A4

a.

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

4.INSPECT FUSES (STOP AND IGN)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E35
1.927,2.344 2.365,2 false 1.594,2.344 1.135,2 false 1.979,2.563 2.344,2.667 false 1.531,2.563 1.125,2.688 false 0.521,1.792 1.115,1.479 false 0.083,0.813 0.906,0.99 0.823,0.177 10 false Not Pushed 2.094,0.833 2.635,1.031 0.542,0.198 10 false Pushed 2.427,1.875 2.583,2.052 0.156,0.177 10 false 1 2.406,2.604 2.563,2.781 0.156,0.177 10 false 3 0.958,1.885 1.115,2.063 0.156,0.177 10 false 2 0.958,2.625 1.115,2.802 0.156,0.177 10 false 4 0.125,0.052 2.615,0.406 2.49,0.354 10 false Component without harness connected: (Stop Light Switch) 0.25,1.76 0.552,1.948 0.302,0.188 10 false Pin

a.

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
Pin pushed Below 1 Ω




OK

3.INSPECT ECM (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.INSPECT ECM (STP AND ST1 - VOLTAGE)
U151404E02
1.854,3.667 2.177,4.25 false 1.781,3.667 1.542,4.229 false 2.188,0.24 3.01,0.594 0.823,0.354 10 false Brake Pedal Released 0.677,0.24 1.479,0.604 0.802,0.365 10 false Brake Pedal Depressed 0.26,2.042 2.615,2.396 2.354,0.354 10 false Front view of wire harness connector: (to ECM) 2.094,4.25 2.479,4.448 0.385,0.198 10 false STP 1.365,4.25 1.76,4.438 0.396,0.188 10 false ST1- 0.25,2.969 0.552,3.115 0.302,0.146 10 false A24

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-35 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
A24-36 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUSES (STOP AND IGN)
A162281E01
0.057,0.027 1.764,0.197 1.707,0.170 10 Engine Room Relay Block: 2.819,2.837 3.113,2.993 0.295,0.156 10 IGN 1.037,2.854 1.457,3.010 0.420,0.156 10 STOP 1.209,2.803 1.406,1.662 false 2.922,2.826 2.681,2.009 false

a.

Remove the STOP and IGN fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STOP fuse Always Below 1 Ω
IGN fuse Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE