Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in ECM back up power source circuit
(1 trip detection logic)
·

Open in back up power source circuit

·

Battery

·

Battery terminals

·

EFI NO. 1 fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


MONITOR STRATEGY

Related DTCs P0560: ECM system voltage
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 3 seconds
MIL Operation Immediate (MIL illuminated after next engine start)
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None

TYPICAL MALFUNCTION THRESHOLDS

Stand-by RAM Initialized
ECM power source Less than 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0560.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A164743E01
6.239,3.147 6.609,3.317 0.370,0.170 10 ECM 5.903,2.195 6.114,2.371 0.211,0.177 10 E1 5.917,1.158 6.302,1.321 0.385,0.163 10 BATT 5.575,0.992 5.869,1.161 0.295,0.170 10 A24 5.575,2.202 5.869,2.371 0.295,0.170 10 D74 5.658,0.822 5.772,0.978 0.114,0.156 10 1 5.625,2.027 5.815,2.175 0.191,0.149 10 81 3.865,1.13 4.518,1.303 0.652,0.173 10 EFI NO. 1 0.859,2.965 1.335,3.149 0.475,0.184 10 Battery 3.991,0.843 4.120,1.012 0.128,0.170 10 1 4.236,0.843 4.364,1.012 0.128,0.170 10 2

CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUSE (EFI NO. 1)
A162283E01
0.044,0.021 1.742,0.191 1.698,0.170 10 Engine Room Relay Block: 1.335,2.777 1.972,2.933 0.637,0.156 10 EFI NO. 1 1.161,1.115 1.617,2.777 false

a.

Remove the EFI NO. 1 fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (EFI NO. 1 FUSE - ECM, BATTERY)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (EFI NO. 1 FUSE - ECM, BATTERY)
A379449E01
5.25,0.75 5.667,1 0.417,0.25 5.083,1.323 4.698,2.167 true 0.792,0.073 2.563,0.271 1.771,0.198 10 false Engine Room Relay Block: 1.74,2.229 2.479,2.427 0.74,0.198 10 false EFI NO. 1 4.333,0.146 6.656,0.5 2.323,0.354 10 false Front view of wire harness connector: (to ECM) 5.323,0.792 5.698,0.99 0.375,0.198 10 false A24 4.521,2.208 4.979,2.396 0.458,0.188 10 false BATT

a.

Check the harness and connector between the EFI NO. 1 fuse and ECM.

i.

Remove the EFI NO. 1 fuse from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 1 fuse terminal 2 - A24-1 (BATT) Always Below 1 Ω
EFI NO. 1 fuse terminal 2 or A24-1 (BATT) - Body ground Always 10 kΩ or higher




b.

Check the harness and connector between the EFI NO. 1 fuse and battery.

i.

Remove the EFI NO. 1 fuse from the engine room relay block.


ii.

Disconnect the negative battery terminal.


iii.

Disconnect the positive battery terminal.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - EFI NO. 1 fuse terminal 1 Always Below 1 Ω
Battery positive (+) terminal or EFI NO. 1 fuse terminal 1- Body ground Always 10 kΩ or higher





OK

3.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BATTERY
a.

Check that the battery is not depleted (See page Engine / Hybrid System>1UR-FE CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

4.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

4.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR BATTERY TERMINAL

5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Wait 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

B