Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


A112620E11
0.74,1.392 1.554,1.669 0.813,0.276 10 APP Sensor 1.263,1.669 1.744,1.850 0.480,0.181 10 Magnet 0.339,1.842 0.865,2.023 0.526,0.181 10 IC No. 1 0.311,3.318 0.837,3.499 0.526,0.181 10 IC No. 2 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.415,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.794,4.257 2.424,0.202 10 Accelerator Pedal Turning Angle (°) 0.239,5.18 2.518,5.361 2.279,0.181 10 *1: Accelerator Pedal Fully Released 0.239,5.488 2.626,5.653 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.867,3.491 1.347,3.672 0.480,0.181 10 Magnet 0.843,2.878 0.554,3.289 false 0.965,3.195 1.049,3.475 false 0.927,2.504 0.862,1.934 false 1.067,2.205 1.245,1.729 false 1.871,0.851 3.925,1.127 2.054,0.276 10 APP Sensor Output Voltage (V) 4.355,1.841 3.869,0.944 false

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


P2122 VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCP1 circuit

·

Open or ground short in VPA circuit

·

ECM


P2123 VPA 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

ECM


P2125 VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


P2127 VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 4.8 V or more
(b) VPA between 0.4 V and 3.45 V
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 0.02 V or less
(b) VPA 0.4 V or less and VPA2 1.2 V or less
·

Short between VPA and VPA2 circuits

·

Accelerator pedal sensor assembly

·

ECM



HINT:

When any of these DTCs are stored, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area Accel Sensor Out No. 1
When AP Released
Accel Sensor Out No. 2
When AP Released
Accel Sensor Out No. 1
When AP Depressed
Accel Sensor Out No. 2
When AP Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:
·

Accelerator pedal positions are expressed as voltages.


·

AP stands for Accelerator Pedal.



MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P2120: Accelerator pedal position (APP) sensor 1 range check (fluctuating)
P2122: APP sensor 1 range check (low voltage)
P2123: APP sensor 1 range check (high voltage)
P2125: APP sensor 2 range check (fluctuating)
P2127: APP sensor 2 range check (low voltage)
P2128: APP sensor 2 range check (high voltage)
P2138: APP sensor range check (correlation)
Required Sensors/Components (Main) APP sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds: P2120, P2122, P2125 and P2127
2.0 seconds: P2123, P2128 and P2138
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Either of following conditions 1 or 2 met: -
1. Ignition switch off to ON 0.012 seconds or more
2. Throttle actuator power ON

TYPICAL MALFUNCTION THRESHOLDS

P2120
Either of the following conditions is met: 1 or 2
1. All of following conditions met: (a) and (b)
(a) VPA voltage 0.4 V or less
(b) VPA2 voltage - Learned VPA2 accelerator off position voltage 0.04 V or more
2. VPA voltage 4.8 V or more

P2122
All of following conditions met: (a) and (b)
(a) VPA voltage 0.4 V or less
(b) VPA2 voltage - Learned VPA2 accelerator off position voltage 0.04 V or more

P2123
VPA voltage 4.8 V or more

P2125
Either of the following conditions is met: 1 or 2
1. All of following conditions met: (a) and (b)
(a) VPA2 voltage 1.2 V or less
(b) VPA voltage - Learned VPA accelerator off position voltage 0.04 V or more
2. VPA2 voltage when VPA voltage 0.4 V or more, and 3.45 V or less 4.8 V or more

P2127
All of following conditions met: (a) and (b)
(a) VPA2 voltage 1.2 V or less
(b) VPA voltage - Learned VPA accelerator off position voltage 0.04 V or more

P2128
VPA2 voltage when VPA voltage 0.4 V or more, and 3.45 V or less 4.8 V or more

P2138
Either of following conditions A or B met: -
Condition A -
Difference between VPA and VPA 2 voltages 0.02 V or less
Condition B -
VPA voltage 0.4 V or less
VPA2 voltage 1.2 V or less

COMPONENT OPERATING RANGE

VPA voltage 0.4 to 4.8 V
VPA2 voltage 1.2 to 4.8 V
Difference between VPA and VPA2 voltages More than 0.02 V

CONFIRMATION DRIVING PATTERN

A199317E01
0.12,0.098 1.732,0.272 1.611,0.174 10 Accelerator Pedal State 0.865,0.418 1.583,0.567 0.719,0.149 10 Depressed 0.95,0.878 1.592,1.034 0.642,0.156 10 Released 0.432,2.405 1.636,2.575 1.205,0.170 10 Ignition Switch ON 2.092,2.489 2.290,2.673 0.198,0.184 10 [A] 4.414,3.434 4.632,3.611 0.218,0.177 10 [C] 5.364,1.69 6.006,1.846 0.642,0.156 10 Released 2.877,3.049 3.553,3.226 0.677,0.177 10 5 seconds 3.006,1.226 3.725,1.375 0.719,0.149 10 Depressed 3.868,1.129 4.058,1.306 0.191,0.177 10 [B] 3.634,2.007 2.767,1.303 2.767,1.303 2.93,1.303 false 4.728,2.416 5.116,1.774 5.116,1.774 5.261,1.774 false 2.59,2.008 3.232,2.164 0.642,0.156 10 Released 2.207,2.416 2.44,2.073 2.44,2.073 2.543,2.073 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters failsafe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A162855E01
6.012,3.118 6.353,3.274 0.341,0.156 10 ECM 5.583,0.363 5.896,0.528 0.313,0.165 10 VPA 5.583,0.998 5.896,1.163 0.313,0.165 10 EPA 5.592,1.227 5.998,1.392 0.406,0.165 10 VCPA 5.592,1.638 5.989,1.803 0.397,0.165 10 VPA2 5.592,2.245 5.989,2.410 0.397,0.165 10 EPA2 5.592,2.488 5.998,2.653 0.406,0.165 10 VCP2 1.606,0.465 1.920,0.631 0.313,0.165 10 VPA 1.606,0.888 1.920,1.054 0.313,0.165 10 EPA 1.498,1.301 1.904,1.467 0.406,0.165 10 VCPA 1.52,1.722 1.916,1.887 0.397,0.165 10 VPA2 1.528,2.143 1.924,2.309 0.397,0.165 10 EPA2 1.512,2.569 1.918,2.734 0.406,0.165 10 VCP2 6.012,2.969 6.310,3.134 0.298,0.165 10 A24 5.349,0.39 5.551,0.555 0.202,0.165 10 55 1.987,0.386 2.101,0.551 0.114,0.165 10 6 1.987,0.806 2.101,0.972 0.114,0.165 10 5 1.987,1.227 2.101,1.392 0.114,0.165 10 4 1.987,1.647 2.101,1.812 0.114,0.165 10 3 1.987,2.067 2.101,2.232 0.114,0.165 10 2 1.987,2.488 2.101,2.653 0.114,0.165 10 1 5.349,0.801 5.551,0.966 0.202,0.165 10 58 5.349,1.224 5.551,1.389 0.202,0.165 10 57 5.349,1.643 5.551,1.808 0.202,0.165 10 56 5.349,2.065 5.551,2.231 0.202,0.165 10 60 5.349,2.484 5.551,2.649 0.202,0.165 10 59 0.151,2.984 0.458,3.149 0.306,0.165 10 A14 0.142,3.141 2.298,3.307 2.156,0.165 10 Accelerator Pedal Position Sensor

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the Accelerator Pedal Position (APP) sensor.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR)
FI07052E62
0.385,1.771 1.125,1.969 0.74,0.198 10 false Depressed 2.365,1.771 3.01,1.969 0.646,0.198 10 false Released

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the value displayed on the Techstream.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V More than 0.02 V
Depressed 2.6 to 4.5 V 3.4 to 4.75 V


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
A379576E01
1.656,0.979 2.052,1.208 0.396,0.229 4.99,0.854 5.385,1.083 0.396,0.229 1.563,1.698 1.26,1.979 true 1.677,1.719 1.552,2.167 true 1.792,1.719 1.875,2.25 true 1.917,1.688 2.188,2.156 true 2.042,1.698 2.615,2.146 true 2.146,1.688 2.667,1.865 true 5.281,1.896 4.792,2.292 true 5.354,1.896 5.073,2.365 true 5.427,1.896 5.344,2.49 true 5.49,1.896 5.583,2.375 true 5.573,1.906 5.844,2.292 true 5.635,1.896 6.01,2.115 true 0.698,0.104 3.01,0.469 2.313,0.365 10 false Front view of wire harness connector: (to APP Sensor) 3.948,0.083 6.26,0.448 2.313,0.365 10 false Front view of wire harness connector: (to ECM) 1.719,1.01 2.042,1.198 0.323,0.188 10 false A14 5.063,0.885 5.385,1.073 0.323,0.188 10 false A24 0.885,1.979 1.323,2.177 0.438,0.198 10 false VCP2 1.25,2.188 1.688,2.385 0.438,0.198 10 false EPA2 1.708,2.281 2.146,2.479 0.438,0.198 10 false VPA2 2.125,2.188 2.563,2.385 0.438,0.198 10 false VCPA 2.625,2.125 3.063,2.323 0.438,0.198 10 false EPA 2.729,1.833 3.167,2.031 0.438,0.198 10 false VPA 4.833,2.385 5.271,2.583 0.438,0.198 10 false VPA2 4.406,2.24 4.844,2.438 0.438,0.198 10 false VPA 5.167,2.552 5.604,2.75 0.438,0.198 10 false VCPA 5.521,2.396 5.958,2.594 0.438,0.198 10 false EPA 5.875,2.281 6.313,2.479 0.438,0.198 10 false VCP2 6.083,2.042 6.521,2.24 0.438,0.198 10 false EPA2

a.

Disconnect the APP sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A14-6 (VPA) - A24-55 (VPA) Always Below 1 Ω
A14-5 (EPA) - A24-58 (EPA) Always Below 1 Ω
A14-4 (VCPA) - A24-57 (VCPA) Always Below 1 Ω
A14-3 (VPA2) - A24-56 (VPA2) Always Below 1 Ω
A14-2 (EPA2) - A24-60 (EPA2) Always Below 1 Ω
A14-1 (VCP2) - A24-59 (VCP2) Always Below 1 Ω
A14-6 (VPA) or A24-55 (VPA) - Body ground Always 10 kΩ or higher
A14-5 (EPA) or A24-58 (EPA) - Body ground Always 10 kΩ or higher
A14-4 (VCPA) or A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A14-3 (VPA2) or A24-56 (VPA2) - Body ground Always 10 kΩ or higher
A14-2 (EPA2) or A24-60 (EPA2) - Body ground Always 10 kΩ or higher
A14-1 (VCP2) or A24-59 (VCP2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
U151406E01
0.063,0.022 2.467,0.387 2.404,0.365 10 Front view of wire harness connector: (to APP Sensor) 0.463,1.737 0.727,1.918 0.264,0.181 10 A14 1.778,2.518 2.178,2.686 0.400,0.167 10 VCPA 0.474,2.518 0.874,2.686 0.400,0.167 10 VCP2 2.427,2.518 2.749,2.686 0.323,0.167 10 EPA 1.134,2.518 1.544,2.686 0.409,0.167 10 EPA2 0.717,2.479 1.304,1.83 false 1.355,2.484 1.462,1.858 false 1.981,2.484 1.733,1.858 false 2.511,2.473 1.896,1.858 false

a.

Disconnect the accelerator pedal position (APP) sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A14-4 (VCPA) - A14-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A14-1 (VCP2) - A14-2 (EPA2) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Read DTCs.

Result
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 is output A
No DTC is output B



A

B

END