Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

By a built-in sensor unit, the manifold absolute pressure sensor detects the intake manifold pressure as a voltage.

A207508E20
0.104,0.031 0.99,0.25 0.885,0.219 10 false Voltage (V) 0.26,0.625 0.542,0.802 0.281,0.177 10 false 4.2 0.25,0.865 0.521,1.042 0.271,0.177 10 false 3.6 0.271,1.333 0.552,1.552 0.281,0.219 10 false 2.4 0.25,1.75 0.51,1.917 0.26,0.167 10 false 1.2 0.25,1.948 0.542,2.135 0.292,0.188 10 false 1.0 1.115,2.438 1.604,2.594 0.49,0.156 10 false 19.988 1.604,2.635 2.104,2.844 0.5,0.208 10 false 59.995 2.115,2.438 2.615,2.615 0.5,0.177 10 false 99.992 2.573,2.656 3.115,2.854 0.542,0.198 10 false 119.990 3.094,2.281 3.427,2.479 0.333,0.198 10 false kPa 0.99,3.115 1.281,3.323 0.292,0.208 10 false 100 1.167,2.938 1.458,3.115 0.292,0.177 10 false 150 1.729,2.927 2.01,3.104 0.281,0.177 10 false 450 2.344,2.927 2.615,3.125 0.271,0.198 10 false 750 2.667,2.938 2.99,3.135 0.323,0.198 10 false 900 0.896,2.646 1.385,2.792 0.49,0.146 10 false 13.332 2.854,3.125 3.323,3.313 0.469,0.188 10 false mmHg

DTC No. DTC Detection Condition Trouble Area
P0107 The manifold absolute pressure sensor voltage is below 0.5 V for 0.5 seconds.
(1 trip detection logic)
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


P0108 The manifold absolute pressure sensor voltage is higher than 4.5 V for 0.5 seconds.
(1 trip detection logic)
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



HINT:

When any of these DTCs are output, check the manifold absolute pressure using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


MAP Malfunction
Approximately 0 kPa
·

Short in PIM circuit to ground

·

Open in VC circuit


130 kPa or higher
·

Short in VC circuit to PIM circuit

·

Open in PIM circuit

·

Open in E2 circuit



MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold pressure sensor and sets a DTC.

Example:

When the sensor output voltage remains less than 0.5 V, or more than 4.5 V for more than 0.5 seconds, the ECM sets a DTC.

If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P0107: Manifold Absolute Pressure (MAP) sensor range check (Low voltage)
P0108: Manifold Absolute Pressure (MAP) sensor range check (High voltage)
Required Sensors/Components (Main) Manifold absolute pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Starter Off
Battery voltage 8 V or more
Ignition switch On (IG)
Time after starter ON to OFF 2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

P0107
MAP sensor voltage Below 0.5 V

P0108
MAP sensor voltage Higher than 4.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 5 seconds [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0107 or P0108.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.


13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165731E77
0.583,2.021 0.885,2.198 0.302,0.177 10 false D80 0.583,2.198 2.823,2.375 2.24,0.177 10 false Manifold Absolute Pressure Sensor 5.938,2.021 6.24,2.198 0.302,0.177 10 false D74 5.927,2.167 6.354,2.344 0.427,0.177 10 false ECM 1.49,1.021 1.76,1.198 0.271,0.177 10 false E2 1.438,1.573 1.781,1.76 0.344,0.188 10 false PIM 1.479,0.458 1.771,0.625 0.292,0.167 10 false VC 5.698,1.573 6.094,1.76 0.396,0.188 10 false PIM 5.698,1.031 6.021,1.25 0.323,0.219 10 false E2 5.698,0.448 6.135,0.635 0.438,0.188 10 false VCV2 1.854,0.594 1.979,0.771 0.125,0.177 10 false 3 1.844,1.167 1.969,1.344 0.125,0.177 10 false 2 1.844,1.688 1.969,1.865 0.125,0.177 10 false 1 5.396,0.573 5.615,0.802 0.219,0.229 10 false 66 5.385,1.146 5.625,1.333 0.24,0.188 10 false 98 5.406,1.688 5.615,1.875 0.208,0.188 10 false 97

CAUTION / NOTICE / HINT

HINT:
·

If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


e.

Read the MAP value.

OK:

Same value as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.





OK

NG

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (TERMINAL VOLTAGE)
2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (TERMINAL VOLTAGE)
a.
U151681E01
0.119,0.145 2.581,0.482 2.461,0.336 10 Front view of wire harness connector: (to Manifold Absolute Pressure Sensor) 0.231,1.933 0.540,2.089 0.309,0.156 10 D80 2.09,2.809 2.315,2.965 0.225,0.156 10 VC 1.454,2.809 1.651,2.965 0.198,0.156 10 E2 0.783,2.809 1.064,2.965 0.281,0.156 10 PIM 0.927,2.784 1.219,2.148 false 1.563,2.191 1.563,2.784 false 2.216,2.784 1.95,2.165 false

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D80-3 (VC) - D80-2 (E2) Ignition switch ON 4.5 to 5.5 V
D80-1 (PIM) - D80-2 (E2) Ignition switch ON 3.0 to 5.0 V




OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and wait for 2 seconds.


f.

Turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTCs.

Result
Display (DTC output) Proceed to
No DTC output A
DTC P0107 and/or P0108 output B



A

END

B

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.

A379416E01
1.667,0.938 2.073,1.167 0.406,0.229 4.802,0.896 5.208,1.125 0.406,0.229 1.438,1.844 1.115,2.229 false 1.729,1.875 1.813,2.26 false 2.063,1.854 2.344,2.26 false 4.219,1.823 4.073,2.344 false 4.854,1.896 5.5,2.344 false 4.781,1.906 4.688,2.365 false 0.448,0.188 2.958,0.604 2.51,0.417 10 false Front view of wire harness connector: (to Manifold Absolute Pressure Sensor) 3.948,0.167 6.25,0.563 2.302,0.396 10 false Front view of wire harness connector: (to ECM) 1.74,0.979 2.104,1.177 0.365,0.198 10 false D80 4.875,0.927 5.24,1.125 0.365,0.198 10 false D74 0.948,2.24 1.292,2.448 0.344,0.208 10 false PIM 1.719,2.281 2.063,2.49 0.344,0.208 10 false E2 2.281,2.281 2.625,2.49 0.344,0.208 10 false VC 3.906,2.365 4.385,2.583 0.479,0.219 10 false VCV2 4.552,2.396 5.031,2.615 0.479,0.219 10 false PIM 5.531,2.333 6.01,2.552 0.479,0.219 10 false E2


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D80-1 (PIM) - D74-97 (PIM) Always Below 1 Ω
D80-3 (VC) - D74-66 (VCV2) Always Below 1 Ω
D80-2 (E2) - D74-98 (E2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D80-1 (PIM) or D74-97 (PIM) - Body ground Always 10 kΩ or higher
D80-3 (VC) or D74-66 (VCV2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR