Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM D

1UR-FE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

HINT:

If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.



A317524E15
0.375,1.125 2.063,1.323 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.458,0.177 3.042,0.365 0.583,0.188 10 false DTC set 0.406,2.781 2.792,2.979 2.385,0.198 10 false Freeze frame data which can be read

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, 5 separate sets of freeze frame data can be checked.

·

3 data sets before the DTC was stored.

·

1 data set when the DTC was stored.

·

1 data set after the DTC was stored.



These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.


LIST OF FREEZE FRAME DATA


Tester Display Measurement Item Diagnostic Note
Vehicle Speed Vehicle speed Speed indicated on speedometer.
Engine Speed Engine speed -
Calculate Load Calculated load Load calculated by ECM.
Vehicle Load Vehicle load -
MAF Mass air flow volume If approximately 0.0 gm/sec.:
·

Mass air flow meter power source circuit open or shorted.


·

VG circuit open or shorted.


If 160.0 gm/sec. or more:
·

E2G circuit open.


Atmosphere Pressure Atmospheric pressure -
MAP Intake manifold pressure -
Coolant Temp Engine coolant temperature If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Intake Air Intake air temperature If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Engine Run Time Accumulated engine running time -
Initial Engine Coolant Temp Engine coolant temperature at engine start -
Coolant Temp Variation after Engine Start Coolant temp variation after engine start -
Initial Intake Air Temp Intake air temperature at engine start -
Intake Air Temp Variation after Engine Start Intake air temp variation after engine start -
Battery Voltage Battery voltage -
Accel Sens. No.1 Volt % Absolute Accelerator Pedal Position (APP) No. 1 -
Accel Sens. No.2 Volt % Absolute APP No. 2 -
Throttle Sensor Volt % Throttle sensor position -
Throttl Sensor #2 Volt % Throttle sensor position #2 -
Throttle Sensor Position Throttle position -
Throttle Motor DUTY Throttle actuator -
Throttle Position Throttle position For use when engine stall, starting problems or rough idle is present.
ISC Flow Flow rate calculated using information from each sensor For use when engine stall, starting problems or rough idle is present.
ISC Position Requested opening amount calculated using ISC control For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value ISC feedback compensation amount For use when engine stall, starting problems or rough idle is present.
ISC Learning Value ISC learned compensation amount For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val Compensation flow rate according to electrical load For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val Compensation flow rate according to air conditioner load For use when engine stall, starting problems or rough idle is present.
PS Feedback Val Compensation flow rate according to power steering load For use when engine stall, starting problems or rough idle is present.
Low Revolution Control Low engine speed control operation state For use when engine stall, starting problems or rough idle is present.
N Range Status Shift lever N status For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow Intake air compensation flow rate For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow Flow loss due to deposits For use when engine stall, starting problems or rough idle is present.
Fuel Pump Duty Fuel pump duty -
Injector (Port) Injection period of No. 1 cylinder -
Injection Volum (Cylinder 1) Injection volume -
Vacuum Pump Key-off EVAP system leak detection pump status Refer to EVAP System (See page (Click here)).
Current Fuel Type Status of the current fuel type -
EVAP (Purge) VSV EVAP purge VSV duty ratio -
Evap Purge Flow Ratio of evaporative purge flow to intake air volume -
Purge Density Learn Value Learning value of purge density -
EVAP System Vent Valve Key-off EVAP system vent valve status -
EVAP Purge VSV EVAP purge VSV -
Purge Cut VSV Duty Purge cut VSV duty -
Target Air-Fuel Ratio Ratio compared to stoichiometric level -
AF Lambda B1S1 Fuel trim at A/F sensor -
AF Lambda B2S1 Fuel trim at A/F sensor -
AFS Voltage B1S1
AFS Voltage B2S1
A/F sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Current B1S1 A/F sensor current -
AFS Current B2S1 A/F sensor current -
A/F Heater Duty #1 A/F heater duty ratio (for Bank 1) -
A/F Heater Duty #2 A/F heater duty ratio (for Bank 2) -
O2S B1S2
O2S B2S2
Heated oxygen sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S Impedance B1S2
O2S Impedance B2S2
Sub heated oxygen sensor impedance (for Sensor 2) -
O2 Heater B1S2
O2 Heater B2S2
Heated oxygen sensor heater (for Sensor 2) -
O2 Heater Curr Val B1S2
O2 Heater Curr Val B2S2
Heated oxygen sensor current (for Sensor 2) -
Short FT #1 Short-term fuel trim Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #1 Long-term fuel trim
·

Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value.

·

Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.


A/F Learn Value Idle #1 Air fuel ratio learned value for idling (for Bank 1) Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #1 Air fuel ratio learned value for low engine loads (for Bank 1) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1 Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1 Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1 Air fuel ratio learned value for high engine loads (for Bank 1) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #1 Total fuel trim -
Short FT #2 Short-term fuel trim Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #2 Long-term fuel trim
·

Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value.

·

Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.


A/F Learn Value Idle #2 Air fuel ratio learned value for idling (for Bank 2) Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #2 Air fuel ratio learned value for low engine loads (for Bank 2) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #2 Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #2 Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #2 Air fuel ratio learned value for high engine loads (for Bank 2) Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #2 Total fuel trim -
Fuel System Status #1 Fuel system status (for Bank 1)
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using A/F sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to detected system fault.

·

CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.


Fuel System Status #2 Fuel system status (for Bank 2)
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Using A/F sensor as feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment).

·

OL Fault: Open loop due to detected system fault.

·

CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.


Air pump pressure (Absolute) Air pump pressure (for Bank 1) -
Air Pump2 Pressure (Absolute) Air pump pressure (for Bank 2) -
Air Pump Pulsation Pressure Air pump pulsation pressure (for Bank 1) -
Air Pump2 Pulsation Pressure Air pump pulsation pressure (for Bank 2) -
Secondary Air Control VSV Secondary air injection system status -
2nd Air System Status Secondary air injection system status -
AI Test Secondary air injection system operation prohibition -
Subfreezing Conditions Subfreezing conditions status -
Air Pump Freeze Air pump freeze status (for Bank 1) -
Air Pump2 Freeze Air pump2 freeze status (for Bank 2) -
Air Switching Valve Freeze Air switching valve freeze status (for Bank 1) -
Air Switching Valve2 Freeze Air switching valve2 freeze status (for Bank 2) -
Air Pump Heater Air pump heater status -
IGN Advance Ignition advance -
Knock Feedback Value Feedback value of knocking -
Knock Correct Learn Value Correction learning value of knocking -
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #7 Individual cylinder timing advance compensation amount (No. 7) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #8 Individual cylinder timing advance compensation amount (No. 8) For use when engine stall, starting problems or rough idle is present.
ACIS VSV VSV for Acoustic Control Induction System (ACIS) -
Target EGR Position Target EGR position -
EGR Step Position EGR step position -
Actual VVT Angle #1 Actual VVT displacement angle (bank 1) This item is used for freeze frame data only
Actual VVT Angle #2 Actual VVT displacement angle (bank 2) This item is used for freeze frame data only
Actual VVT Ex Angle #1 Actual VVT exhaust displacement angle (bank 1) This item is used for freeze frame data only
Actual VVT Ex Angle #2 Actual VVT exhaust displacement angle (bank 2) This item is used for freeze frame data only
VVT Control Status #1 VVT control status (bank 1) -
VVT Control Status #2 VVT control status (bank 2) -
VVT Advance Fail VVT control failure status -
Catalyst Temp B1S1 Estimated catalyst temperature (for Bank 1 Sensor 1) -
Catalyst Temp B2S1 Estimated catalyst temperature (for Bank 2 Sensor 1) -
Catalyst Temp B1S2 Estimated catalyst temperature (for Bank 1 Sensor 2) -
Catalyst Temp B2S2 Estimated catalyst temperature (for Bank 2 Sensor 2) -
Starter Signal Starter switch (STSW) signal -
Starter Control Starter switch status -
Power Steering Signal Power steering switch status -
Starter Relay Starter relay status -
ACC Relay ACC relay status -
Neutral Position SW Signal Park/neutral position (PNP) switch signal -
Transfer L4 L4 status of the transfer -
Stop Light Switch Stop light switch -
A/C Signal A/C signal -
Closed Throttle Position SW Closed throttle position switch -
Fuel Cut Condition Fuel cut condition -
Immobiliser Communication Immobiliser communication -
TC Terminal TC terminal status -
Time after DTC Cleared Cumulative time after DTCs cleared -
Distance from DTC Cleared Accumulated distance after DTCs cleared -
Warmup Cycle Cleared DTC Warm-up cycles after DTCs cleared -
Dist Batt Cable Disconnect Total distance vehicle driven after battery cable disconnected -
IG OFF Elapsed Time Cumulative time after ignition switch off -
TC and TE1 TC and CG (TE1) terminals of DLC3 -
Total Distance Traveled Total distance traveled -
Ignition Trig. Count Ignition counter -
Cylinder #1 Misfire Count Misfire count of cylinder No. 1 -
Cylinder #2 Misfire Count Misfire count of cylinder No. 2 -
Cylinder #3 Misfire Count Misfire count of cylinder No. 3 -
Cylinder #4 Misfire Count Misfire count of cylinder No. 4 -
Cylinder #5 Misfire Count Misfire count of cylinder No. 5 -
Cylinder #6 Misfire Count Misfire count of cylinder No. 6 -
Cylinder #7 Misfire Count Misfire count of cylinder No. 7 -
Cylinder #8 Misfire Count Misfire count of cylinder No. 8 -
All Cylinders Misfire Count All cylinders misfire -
Multi Cylinders Misfire Count Multiple cylinder misfire -
Misfire RPM Engine speed when misfire occurred -
Misfire Load Engine load when misfire occurred -
Misfire Margin Margin to detect engine misfire -
Catalyst OT MF F/C Catalyst over temperature misfire prevention F/C -
Cat OT MF F/C History Catalyst over temperature misfire prevention F/C history -
Cat OT MF F/C Cylinder#1 Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#2 Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#3 Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#4 Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#5 Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#6 Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#7 Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#8 Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected) -
Engine Speed (Starter Off) Engine speed when starter off For use when engine stall, starting problems or rough idle is present.
Starter Count Number of times starter turned on after ignition switch turned to ON For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip Distance driven during previous trip Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time Time elapsed after engine started (interval between ignition switch ON and off) For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp Engine coolant temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp Intake air temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature Engine oil temperature (estimated temperature) For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C Ambient temperature for A/C For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp Ambient temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation History of hesitation during engine start For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start History of low engine speed after engine start For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed Minimum engine speed For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure Power steering oil pressure sensor -
ACT VSV A/C cut status for Active Test -
Electric Cooling Fan Low Electric fan motor operation status -
Brake Override System Brake Override System -
Idle Fuel Cut Fuel cut at idle ON: when throttle valve fully closed and engine speed over 3500 rpm.
FC TAU Fuel cut during very light load Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
Immobiliser Fuel Cut Status of the immobiliser fuel cut -
Immobiliser Fuel Cut History Status of the immobiliser fuel cut history -
Vehicle Spec Signal 1 Status of the Vehicle Spec Judge Signal 1 -
Electrical Load Signal 1 Electrical load signal 1 -
Electrical Load Signal 2 Electrical load signal 2 -
Cruise Cancel Signal Status of the cruise cancel signal -
A/F Sensor Determination (worst value) #1 Worst judgment value of air fuel ratio sensor output (bank 1) -
A/F Sensor Determination (worst value) #2 Worst judgment value of air fuel ratio sensor output (bank 2) -
Engine Speed Fluctuation Avg (worst value) #1 Worst value of average engine speed fluctuation (Cylinder No. 1) -
Engine Speed Fluctuation Avg (worst value) #2 Worst value of average engine speed fluctuation (Cylinder No. 2) -
Engine Speed Fluctuation Avg (worst value) #3 Worst value of average engine speed fluctuation (Cylinder No. 3) -
Engine Speed Fluctuation Avg (worst value) #4 Worst value of average engine speed fluctuation (Cylinder No. 4) -
Engine Speed Fluctuation Avg (worst value) #5 Worst value of average engine speed fluctuation (Cylinder No. 5) -
Engine Speed Fluctuation Avg (worst value) #6 Worst value of average engine speed fluctuation (Cylinder No. 6) -
Engine Speed Fluctuation Avg (worst value) #7 Worst value of average engine speed fluctuation (Cylinder No. 7) -
Engine Speed Fluctuation Avg (worst value) #8 Worst value of average engine speed fluctuation (Cylinder No. 8) -
SPD (NT) Input shaft speed Data displayed in increments of 50 rpm.
SPD (SP2) Output shaft speed -
Overdrive Cut Switch #1 Overdrive cut signal for cruise control -
Shift SW Status (P Range) PNP switch status (P Range) When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status (R Range) When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/Neutral position (PNP) switch status (N Range) When shift lever position displayed on Techstream differs from actual position, adjustment of Park/Neutral position (PNP) switch signal or shift cable may be incorrect.
Shift SW Status (N,P Range) Supported Status of PNP switch (N or P) supported -
Shift SW Status (N,P Range) PNP switch status (N or P Range) -
Sports Shift Up SW Sport shift up switch status -
Sports Shift Down SW Sport shift down switch status -
Sports Mode Selection SW Sport mode select switch status -
Shift SW Status (D Range) PNP switch status (D Range) When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
A/T Oil Temperature 1 No. 1 ATF temperature sensor value If value -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit open or shorted.
A/T Oil Temperature 2 No. 2 ATF temperature sensor value If value -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit open or shorted.
Lock Up Lock-up -
Shift Status ECM gear shift command -
SLT Solenoid Status Shift solenoid SLT status -
SLU Solenoid Status Shift solenoid SLU status -