Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  EVAP System  


RELATED DTCS

DTC Code Monitoring Item See page
P043E Reference orifice clogged (built into canister pump module) (Click here)
P043F Reference orifice high-flow (built into canister pump module)
P0441
·

Purge VSV (Vacuum Switching Valve) stuck closed

·

Purge VSV stuck open

·

Purge flow


(Click here)
P0451
·

Canister pressure sensor (built into canister pump module) noise

·

Canister pressure sensor (built into canister pump module) signal becomes fixed/flat


(Click here)
P0452 Canister pressure sensor (built into canister pump module) voltage low
P0453 Canister pressure sensor (built into canister pump module) voltage high
P0455 EVAP gross leak (Click here)
P0456 EVAP small leak
P2401 Leak detection pump stuck OFF (built into canister pump module) (Click here)
P2402 Leak detection pump stuck ON (built into canister pump module)
P2419 Vent valve stuck closed (built into canister pump module) (Click here)
P2420 Vent valve stuck open (vent) (built into canister pump module) (Click here)
P2610 Soak timer (built into ECM) (Click here)

If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.

A235785E17
2.865,0.313 3.385,0.542 0.521,0.229 10 false P0441 2.365,0.208 2.885,0.438 0.521,0.229 10 false P043E 2.365,0.458 2.885,0.688 0.521,0.229 10 false P043F 1.74,0.271 2.271,0.583 0.531,0.313 10 false DTCs 3.365,0.323 3.885,0.552 0.521,0.229 10 false P0451 3.813,0.323 4.333,0.552 0.521,0.229 10 false P0452 4.302,0.333 4.823,0.563 0.521,0.229 10 false P0453 4.781,0.333 5.302,0.563 0.521,0.229 10 false P0455 5.26,0.333 5.781,0.563 0.521,0.229 10 false P0456 5.719,0.219 6.24,0.448 0.521,0.229 10 false P2401 5.719,0.469 6.24,0.698 0.521,0.229 10 false P2402 6.198,0.333 6.635,0.542 0.438,0.208 10 false P2419 6.677,0.344 7.135,0.531 0.458,0.188 10 false P2420 0.135,0.885 2.021,1.083 1.885,0.198 10 false Reference orifice clogged 0.125,1.219 2.01,1.417 1.885,0.198 10 false Reference orifice high-flow 0.115,1.51 2,1.708 1.885,0.198 10 false Purge VSV stuck open 0.115,1.833 2,2.031 1.885,0.198 10 false Purge VSV stuck closed 0.104,2.188 2.073,2.542 1.969,0.354 10 false Canister pressure sensor signal fixed 0.115,2.833 2.104,3.167 1.99,0.333 10 false Canister pressure sensor signal noise 0.125,3.49 1.938,3.854 1.813,0.365 10 false Canister pressure sensor low output 0.104,4.135 1.979,4.49 1.875,0.354 10 false Canister pressure sensor high output 0.115,4.792 2,4.99 1.885,0.198 10 false Gross leak 0.115,5.104 2,5.302 1.885,0.198 10 false Small leak 0.094,5.427 2.146,5.625 2.052,0.198 10 false Leak detection pump stuck OFF 0.115,5.729 2.094,5.927 1.979,0.198 10 false Leak detection pump stuck ON 0.125,6.052 2.01,6.25 1.885,0.198 10 false Vent valve stuck closed 0.125,6.365 2.063,6.563 1.938,0.198 10 false Vent valve stuck open (vent) 0.073,0.531 1.698,0.823 1.625,0.292 10 false Malfunctioning Areas

NOTICE:

If the reference pressure difference between the first and second checks is greater than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) are stored.


DESCRIPTION

A310651E01
0.174,0.093 0.394,0.277 0.220,0.184 10 *a 2.723,0.495 2.897,0.664 0.175,0.170 10 *1 0.102,2.778 0.277,2.948 0.175,0.170 10 *2 2.386,3.553 2.561,3.723 0.175,0.170 10 *3 4.553,7.413 4.727,7.583 0.175,0.170 10 *4 6.102,7.998 6.276,8.168 0.175,0.170 10 *5 2.85,7.364 3.025,7.534 0.175,0.170 10 *6 2.411,7.362 2.586,7.531 0.175,0.170 10 *7 6.481,2.98 6.656,3.150 0.175,0.170 10 *8 2.415,4.938 2.673,5.108 0.258,0.170 10 *9 2.71,5.545 2.949,5.715 0.239,0.170 10 *10 2.261,1.587 2.434,0.559 2.434,0.559 2.686,0.559 false 0.74,2.742 0.364,2.852 0.364,2.852 0.271,2.852 false 2.844,2.964 2.676,3.622 2.676,3.622 2.545,3.622 false 3.307,4.648 2.947,5.007 2.947,5.007 2.662,5.007 false 5.676,3.576 6.2,3.053 6.2,3.053 6.462,3.053 false 5.768,7.904 5.922,8.044 5.922,8.044 6.076,8.044 false 5.104,6.952 4.635,7.211 4.635,7.211 4.635,7.373 false 3.166,6.762 2.931,7.053 2.931,7.053 2.931,7.337 false 3.09,6.665 2.499,7.186 2.499,7.186 2.499,7.337 false 3.627,6.041 3.201,5.614 3.201,5.614 2.939,5.614 false

Text in Illustration
*1 Purge VSV *2 Purge Line Hose (to Intake Manifold)
*3 Purge Line Hose (from Canister) *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Canister Assembly *6 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter)
*7 Fuel Tank Cap Assembly *8 Fuel Tank
*9 Purge Line *10 Bleeding Pipe
*a Location of EVAP (Evaporative Emission) System - -

HINT:

The canister pressure sensor, the leak detection pump and the vent valve are built into the canister pump module.


A204529E15
1.271,1.219 1.031,1.031 1.031,1.031 0.885,1.031 false 1.885,0.906 2.042,0.656 2.042,0.656 2.177,0.656 false 1.917,1.333 1.667,1.573 1.667,1.573 1.531,1.573 false 2.99,0.708 3.094,0.365 3.094,0.365 3.229,0.365 false 3.813,2.844 3.552,2.844 false 4.344,2.938 4.5,2.938 false 3.26,1.531 3.833,1.24 3.833,1.24 3.948,1.24 false 4.885,0.958 5.156,0.698 5.156,0.698 5.302,0.698 false 5.938,1.49 5.875,1.208 5.875,1.208 5.75,1.208 false 5.875,1.854 5.927,2.156 5.927,2.156 6.063,2.156 false 0.24,0.125 0.479,0.323 0.24,0.198 10 false *a 0.698,0.948 0.938,1.146 0.24,0.198 10 false *2 1.323,1.479 1.563,1.677 0.24,0.198 10 false *3 2.229,0.542 2.469,0.74 0.24,0.198 10 false *4 5.313,0.625 5.552,0.823 0.24,0.198 10 false *11 3.365,2.75 3.604,2.948 0.24,0.198 10 false *6 2.969,1.896 3.198,2.052 0.229,0.156 10 true *5 6.104,2.083 6.344,2.281 0.24,0.198 10 false *10 3.281,0.271 3.521,0.469 0.24,0.198 10 false *8 3.063,3.177 3.302,3.375 0.24,0.198 10 false *7 4.302,0.719 4.542,0.917 0.24,0.198 10 false *9 3.969,1.177 4.208,1.375 0.24,0.198 10 false *1 5.49,1.104 5.781,1.281 0.292,0.177 10 false *13 4.521,2.854 4.802,3.042 0.281,0.188 10 false *12

Text in Illustration
*1 Canister Pump Module *2 Intake Manifold
*3 Purge VSV *4 Throttle Valve
*5 Canister Assembly *6 Cut-off Valve
*7 Fuel Tank *8 Air Cleaner
*9 ECM *10 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter)
*11 Soak Timer *12 Roll-over Valve
*13 Fuel Tank Cap Assembly - -
*a EVAP System Circuit - -

NOTICE:

In this vehicle's EVAP system, turning the vent valve ON does not seal off the EVAP system. To check for leaks in the EVAP system, disconnect the air inlet vent hose and apply pressure from the side of the canister exposed to the atmosphere.


While the engine is running, if a predetermined condition (closed loop, etc.) is met, the purge VSV is opened by the ECM and stored fuel vapors in the canister are purged into the intake manifold. The ECM changes the duty cycle of the purge VSV to control purge flow volume.

The purge flow volume is also determined by the intake manifold pressure. Atmospheric pressure is applied to the canister through the vent valve to ensure that the purge flow is maintained when the negative pressure (vacuum) is applied to the canister.

The following two monitors run to confirm the appropriate EVAP system operation.

Key-off monitor


This monitor checks for EVAP (Evaporative Emission) system leaks and canister pump module malfunctions. The monitor starts 5 hours* after the ignition switch is turned off. At least 5 hours are required for the fuel to cool down to stabilize the EVAP pressure, thus making the EVAP system monitor more accurate.

The leak detection pump creates negative pressure (vacuum) in the EVAP system and the pressure is measured. Finally, the ECM monitors for leaks from the EVAP system, and malfunctions in both the canister pump module and purge VSV, based on the EVAP pressure.

HINT:

*: If the engine coolant temperature is not below 35°C (95°F) 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If it is still not below 35°C (95°F) 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.



Purge flow monitor


The purge flow monitor consists of 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

·

The 1st monitor

While the engine is running and the purge VSV (Vacuum Switching Valve) is ON (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If negative pressure is not created, the ECM begins the 2nd monitor.

·

The 2nd monitor

The vent valve is turned OFF (open) and the EVAP pressure is measured. If the variation in the pressure is less than 0.4 kPa-g (3.0 mmHg-g), the ECM interprets this as the purge VSV being stuck closed, and then illuminates the MIL and stores DTC P0441 (2 trip detection logic).



Atmospheric pressure check:

In order to ensure reliable malfunction detection, the variation between the atmospheric pressures, before and after conduction of the purge flow monitor, is measured by the ECM.

A240245E07
2.302,0.969 2.385,0.625 2.385,0.625 2.521,0.625 false 2.979,3.167 3.021,3.531 3.021,3.531 3.167,3.531 false 1.51,2.365 1.573,1.917 1.573,1.917 1.74,1.917 false 1,3.729 1.042,4 1.042,4 1.167,4 false 4.26,2.885 4.052,3.323 4.052,3.323 3.854,3.323 false 5.188,3 5.531,3.292 5.531,3.292 5.708,3.292 false 4.948,2.24 5.021,2.021 5.021,2.021 5.146,2.021 false 4.521,2.583 4.5,2.302 4.5,2.302 4.396,2.302 false 0.844,3.385 1.083,3.583 0.24,0.198 10 false *1 1.198,3.927 1.438,4.125 0.24,0.198 10 false *2 1.781,1.823 2.021,2.021 0.24,0.198 10 false *3 2.563,0.531 2.802,0.729 0.24,0.198 10 false *4 3.24,1.76 3.479,1.958 0.24,0.198 10 false *6 3.208,3.448 3.448,3.646 0.24,0.198 10 false *5 5.719,3.208 5.958,3.406 0.24,0.198 10 false *10 4.208,2.208 4.448,2.406 0.24,0.198 10 false *8 3.646,3.219 3.885,3.417 0.24,0.198 10 false *7 5.198,1.938 5.438,2.135 0.24,0.198 10 false *9 4.948,3.792 5.313,3.99 0.365,0.198 10 false *11 5.948,1.99 6.188,2.188 0.24,0.198 10 false *12 0.896,2.646 1.135,2.844 0.24,0.198 10 false *b 0.115,0.052 0.354,0.25 0.24,0.198 10 false *a

Text in Illustration
*1 ECM *2 Soak Timer
*3 Purge VSV (On) *4 Fuel Tank Cap Assembly
*5 Canister Filter *6 Fuel Tank
*7 Leak Detection Pump (Off) *8 Canister Pressure Sensor
*9 Reference Orifice (0.02 Inches) *10 Vent Valve (Off)
*11 Canister Pump Module *12 Canister Assembly
*a EVAP Purge Flow *b to Intake Manifold

Component Operation
Canister Assembly Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank.
Cut-off valve Located in fuel tank. Valve floats and closes when fuel tank 100% full.
Purge VSV (Vacuum Switching Valve) Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle (time current is flowing) (Open: ON; Closed: OFF).
Roll-over valve Located in fuel tank. Valve closed by its own weight when vehicle overturns to prevent fuel from spilling out.
Soak timer Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min.) after ignition switch turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours have elapsed, ECM activates (refer to fig. 3).
Canister pump module Consists of (a) to (d) below. Canister pump module cannot be disassembled.
(a) Vent valve Vents and closes EVAP system. When ECM turns valve ON, EVAP system closed. When ECM turns valve OFF, EVAP system vented. Negative pressure (vacuum) created in EVAP system to check for EVAP leaks by closing purge VSV, turning on vent valve (closed) and operating leak detection pump (refer to fig. 1).
(b) Canister pressure sensor Indicates pressure as voltages. ECM supplies regulated 5 V to canister pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2).
(c) Leak detection pump Creates negative pressure (vacuum) in EVAP system for leak check.
(d) Reference orifice Has opening with 0.02-inch diameter. Vacuum produced through orifice by closing purge VSV, turning off vent valve and operating leak detection pump to monitor reference pressure. Reference pressure used to detect small leak of EVAP.

A207995E15
3.177,1.76 2.635,2.854 false 5.313,1.823 4.875,2.792 false 6.229,1.75 5.948,2.813 false 2.802,1.885 2.802,2.156 2.802,2.156 1.552,2.844 false 1.25,0.948 2.167,1.406 false 2.313,2.198 1.344,2.292 false 0.177,0.125 0.396,0.354 0.219,0.229 10 false *a 1.573,1.458 1.75,1.625 0.177,0.167 10 false *1 1.344,2.792 1.573,2.979 0.229,0.188 10 false *3 1.135,2.198 1.365,2.385 0.229,0.188 10 false *2 4.042,0.094 4.302,0.26 0.26,0.167 10 false : *b 5.656,0.479 5.854,0.646 0.198,0.167 10 false *d 2.479,2.792 2.719,3.146 0.24,0.354 10 false *g 3.875,1.292 4.115,1.49 0.24,0.198 10 false *f 5.833,2.833 6.094,3 0.26,0.167 10 false *i 2.583,0.573 2.75,0.74 0.167,0.167 10 false *c 4.729,2.792 4.969,2.948 0.24,0.156 10 false *h 1.021,0.844 1.219,1.01 0.198,0.167 10 false *e

Text in Illustration
*1 Canister *2 Reference Orifice (0.02 Inches)
*3 Canister Pressure Sensor - -
*a Canister Pump Module (fig. 1) *b Airflow
*c Condition: Purge Flow *d Condition: Leak Check
*e Vent Valve: Off (Vent) *f to Canister Filter (Atmosphere)
*g Leak Detection Pump: Off *h Vent Valve: on (closed)
*i Leak Detection Pump: on - -

A115543E70
4.552,3.302 4.969,3 true 4.521,1.427 4.958,1.052 true 0.094,0.083 3.083,0.292 2.99,0.208 10 Canister Pressure Sensor Specification: 5.115,3.344 5.792,3.604 0.677,0.26 10 Pressure 1.302,1.021 2.365,1.281 1.063,0.26 10 Output Voltage 1.698,1.448 2.281,1.708 0.583,0.26 10 4.900 V 1.698,1.917 2.281,2.177 0.583,0.26 10 4.423 V 1.698,2.615 2.281,2.875 0.583,0.26 10 1.425 V 1.698,3.094 2.281,3.354 0.583,0.26 10 0.450 V 5.01,2.917 6.135,3.177 1.125,0.26 10 Malfunction Area 5,0.958 6.125,1.219 1.125,0.26 10 Malfunction Area 3.844,2.292 4.813,2.552 0.969,0.26 10 Usable Range 1.833,4.25 6.656,4.479 4.823,0.229 10 Standard atmospheric pressure is 101.3 kPa(abs) [760 mmHg(abs)] 1.833,4.031 2.292,4.292 0.458,0.26 10 HINT: 3.583,3.458 3.969,3.844 0.385,0.385 10 115 (862) 2.896,3.458 3.281,3.844 0.385,0.385 10 60 (450) 4.344,3.448 5.333,3.906 0.99,0.458 10 kPa(abs) [mmHg(abs)]

U151546E01
5.59,4.253 5.936,4.409 0.346,0.156 10 ECM 4.992,1.164 5.731,1.481 0.739,0.317 10 Soak Timer IC 5.029,2.544 5.671,2.876 0.642,0.332 10 Power Source IC 5.002,3.347 5.732,3.670 0.730,0.323 10 Main Relay Control IC 4.324,0.9 4.724,1.056 0.400,0.156 10 IGSW 4.523,2.697 4.739,2.848 0.216,0.151 10 +B 4.303,3.492 4.736,3.649 0.434,0.157 10 MREL 3.175,3.893 3.433,4.049 0.258,0.156 10 EFI 1.895,3.314 2.542,3.470 0.647,0.156 10 EFI NO. 1 0.55,3.875 1.021,4.058 0.471,0.184 10 Battery 1.419,2.343 2.066,2.508 0.647,0.165 10 IG2 MAIN 0.373,2.33 0.705,2.485 0.332,0.156 10 AM2 3.908,1.105 4.194,1.270 0.286,0.165 10 IGN 2.837,1.698 3.095,1.864 0.258,0.165 10 IG2 1.428,1.67 2.371,1.845 0.943,0.174 10 Ignition Switch 0.121,0.058 1.809,0.249 1.688,0.191 10 Soak Timer Circuit (fig. 3):

WIRING DIAGRAM

A164731E22
5.884,7.066 6.221,7.222 0.336,0.156 10 ECM 5.443,0.61 5.891,0.766 0.448,0.156 10 MPMP 5.1,0.62 5.381,0.789 0.281,0.170 10 A24 5.1,3.282 5.381,3.451 0.281,0.170 10 A24 5.1,6.106 5.381,6.276 0.281,0.170 10 A24 5.156,0.456 5.340,0.612 0.184,0.156 10 49 5.436,1.591 5.856,1.750 0.420,0.159 10 VCV1 5.1,1.689 5.388,1.852 0.288,0.163 10 D74 5.149,1.514 5.346,1.684 0.198,0.170 10 67 5.436,2.067 5.870,2.223 0.434,0.156 10 PPMP 5.106,1.969 5.366,2.132 0.260,0.163 10 121 5.1,2.151 5.395,2.307 0.295,0.156 10 D74 5.1,2.608 5.395,2.764 0.295,0.156 10 D74 5.1,4.196 5.395,4.352 0.295,0.156 10 D74 5.436,2.53 5.884,2.686 0.448,0.156 10 E2 5.151,2.437 5.336,2.592 0.185,0.156 10 98 5.436,3.286 5.873,3.446 0.437,0.159 10 VPMP 5.15,3.118 5.347,3.274 0.198,0.156 10 30 5.442,4.203 5.803,4.362 0.361,0.159 10 PRG 5.148,4.035 5.359,4.191 0.211,0.156 10 63 5.436,6.013 5.870,6.169 0.434,0.156 10 MREL 5.152,5.932 5.343,6.081 0.191,0.149 10 34 1.457,0.504 1.919,0.660 0.461,0.156 10 MGND 1.242,0.52 1.393,0.690 0.151,0.170 10 4 2.9,0.504 3.334,0.660 0.434,0.156 10 MTRB 3.37,0.516 3.544,0.672 0.174,0.156 10 3 1.642,3.691 1.946,3.847 0.304,0.156 10 R12 1.642,3.843 3.090,4.027 1.448,0.184 10 Canister Pump Module 1.707,0.792 3.085,0.976 1.378,0.184 10 Leak Detection Pump 1.595,1.682 2.179,2.196 0.584,0.514 10 Canister Pressure Sensor 2.046,3.407 2.743,3.577 0.698,0.170 10 Vent Valve 2.998,1.598 3.328,1.754 0.330,0.156 10 VCC 3.37,1.591 3.578,1.759 0.208,0.167 10 6 2.9,2.041 3.334,2.196 0.434,0.156 10 VOUT 3.371,2.05 3.556,2.206 0.184,0.156 10 7 2.9,2.733 3.348,2.889 0.448,0.156 10 SGND 3.382,2.513 3.542,2.669 0.161,0.156 10 8 2.886,3.197 3.334,3.367 0.448,0.170 10 VGND 1.443,3.195 1.835,3.351 0.392,0.156 10 VLVB 1.264,3.195 1.397,3.365 0.133,0.170 10 5 3.382,3.195 3.674,3.351 0.292,0.156 10 1 3.943,4.467 4.252,4.623 0.309,0.156 10 D29 3.943,4.605 4.683,4.761 0.739,0.156 10 Purge VSV 3.813,4.034 3.928,4.204 0.114,0.170 10 1 4.6,4.038 4.714,4.208 0.114,0.170 10 2 3.313,6.856 4.775,7.040 1.461,0.184 10 Integration Relay 1.408,5.374 2.064,5.544 0.656,0.170 10 EFI NO. 2 2.557,5.893 3.213,6.062 0.656,0.170 10 EFI NO. 1 3.664,6.417 3.931,6.573 0.267,0.156 10 EFI 2.238,5.756 2.456,5.923 0.218,0.166 10 1C 2.296,5.584 2.411,5.740 0.114,0.156 10 1 1.464,6.611 1.953,6.795 0.489,0.184 10 Battery 2.249,5.262 2.464,5.414 0.215,0.152 10 1B 2.725,6.663 2.940,6.816 0.215,0.152 10 1B 4.525,6.108 4.740,6.260 0.215,0.152 10 1B 2.293,5.096 2.407,5.258 0.114,0.162 10 4 4.574,5.937 4.689,6.106 0.114,0.170 10 2 2.527,6.663 2.641,6.819 0.114,0.156 10 3

CAUTION / NOTICE / HINT

NOTICE:

The Techstream is required to conduct the following diagnostic troubleshooting procedure.


HINT:
·

Using the Techstream monitor results enables the EVAP (Evaporative Emission) system to be checked.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



CONFIRMATION DRIVING PATTERN

HINT:

After a repair, check Monitor Status by performing the Key-off Monitor Confirmation and Purge Flow Monitor Confirmation described below.


Key-off monitor confirmation


a.

Preconditions

The monitor will not run unless:
·

The vehicle has been driven for 10 minutes or more (in a city area or on a freeway).

·

The fuel tank is less than 90% full.

·

The elevation is less than 2432 m (8000 ft.).

·

The engine coolant temperature is between 4.4°C and 35°C (40°F and 95°F).

·

The intake air temperature is between 4.4°C and 35°C (40°F and 95°F).

·

The vehicle remains stationary (the vehicle speed is 0 mph [0 km/h]).



b.

Monitor Conditions

1.

Allow the engine to idle for at least 5 minutes.

2.

Turn the ignition switch off and wait for 5 hours (7 or 9.5 hours).

HINT:

Do not start the engine until checking Monitor Status. If the engine is started, the steps described above must be repeated.




c.

Monitor Status

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Evaporative System.

5.

Check the Monitor Status displayed on the Techstream.

HINT:

If INCMP (incomplete) is displayed, the monitor is not complete. Make sure that the preconditions have been met, and then perform the operations listed under Monitor Conditions again.





Purge flow monitor confirmation (P0441)


HINT:

Perform this monitor confirmation after the Key-off Monitor Confirmation shows COMPL (complete).


a.

Preconditions

The monitor will not run unless:
·

The vehicle has been driven for 10 minutes or more (in a city area or on a freeway).

·

The engine coolant temperature is between 4.4°C and 35°C (40°F and 95°F).

·

The intake air temperature is between 4.4°C and 35°C (40°F and 95°F).



b.

Monitor Conditions

1.

Release the pressure from the fuel tank by removing and reinstalling the fuel tank cap.

2.

Warm the engine up until the engine coolant temperature is higher than 75°C (167°F).

3.

Increase the engine speed to 3000 rpm once.

4.

Allow the engine to idle and turn the A/C on for 1 minute.



c.

Monitor Status

1.

Turn the ignition switch off (if ON or if the engine is running).

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Monitor.

5.

Check the Monitor Status displayed on the Techstream.

HINT:

If INCMP (incomplete) is displayed, the monitor is not complete. Make sure that the preconditions have been met, and then perform the operations listed under Monitor Conditions again





MONITOR RESULT

PROCEDURE

1.CONFIRM DTC
a.

Turn the ignition switch off and wait for 10 seconds.


b.

Turn the ignition switch to ON.


c.

Turn the ignition switch off and wait for 10 seconds.


d.

Connect the Techstream to the DLC3.


e.

Turn the ignition switch to ON and turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm DTCs and freeze frame data.

If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.


A235785E17
2.865,0.313 3.385,0.542 0.521,0.229 10 false P0441 2.365,0.208 2.885,0.438 0.521,0.229 10 false P043E 2.365,0.458 2.885,0.688 0.521,0.229 10 false P043F 1.74,0.271 2.271,0.583 0.531,0.313 10 false DTCs 3.365,0.323 3.885,0.552 0.521,0.229 10 false P0451 3.813,0.323 4.333,0.552 0.521,0.229 10 false P0452 4.302,0.333 4.823,0.563 0.521,0.229 10 false P0453 4.781,0.333 5.302,0.563 0.521,0.229 10 false P0455 5.26,0.333 5.781,0.563 0.521,0.229 10 false P0456 5.719,0.219 6.24,0.448 0.521,0.229 10 false P2401 5.719,0.469 6.24,0.698 0.521,0.229 10 false P2402 6.198,0.333 6.635,0.542 0.438,0.208 10 false P2419 6.677,0.344 7.135,0.531 0.458,0.188 10 false P2420 0.135,0.885 2.021,1.083 1.885,0.198 10 false Reference orifice clogged 0.125,1.219 2.01,1.417 1.885,0.198 10 false Reference orifice high-flow 0.115,1.51 2,1.708 1.885,0.198 10 false Purge VSV stuck open 0.115,1.833 2,2.031 1.885,0.198 10 false Purge VSV stuck closed 0.104,2.188 2.073,2.542 1.969,0.354 10 false Canister pressure sensor signal fixed 0.115,2.833 2.104,3.167 1.99,0.333 10 false Canister pressure sensor signal noise 0.125,3.49 1.938,3.854 1.813,0.365 10 false Canister pressure sensor low output 0.104,4.135 1.979,4.49 1.875,0.354 10 false Canister pressure sensor high output 0.115,4.792 2,4.99 1.885,0.198 10 false Gross leak 0.115,5.104 2,5.302 1.885,0.198 10 false Small leak 0.094,5.427 2.146,5.625 2.052,0.198 10 false Leak detection pump stuck OFF 0.115,5.729 2.094,5.927 1.979,0.198 10 false Leak detection pump stuck ON 0.125,6.052 2.01,6.25 1.885,0.198 10 false Vent valve stuck closed 0.125,6.365 2.063,6.563 1.938,0.198 10 false Vent valve stuck open (vent) 0.073,0.531 1.698,0.823 1.625,0.292 10 false Malfunctioning Areas

NOTICE:

If the reference pressure difference between the first and second checks is greater than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) are stored.



NEXT

2.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
2.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


c.

After Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

HINT:

If no pending DTCs are displayed, perform Monitor Confirmation (see "Diagnostic Help" menu). After this confirmation, check for pending DTCs. If no DTCs are displayed, the EVAP system is normal.




NEXT

3.PERFORM EVAPORATIVE SYSTEM CHECK (MANUAL MODE)
3.PERFORM EVAPORATIVE SYSTEM CHECK (MANUAL MODE)
U151691E02
0.979,3.146 1.115,3.406 false 5.26,3.698 5.073,3.406 false 6.146,3.333 5.969,3.063 false 0.406,0.604 1.188,0.813 0.781,0.208 10 false Purge VSV 0.406,1.052 1.208,1.26 0.802,0.208 10 false Vent Valve 0.115,1.385 1.115,1.74 1,0.354 10 false Leak Detection Pump 0.063,2 1.177,2.208 1.115,0.208 10 false EVAP Pressure 0.229,2.219 0.938,2.427 0.708,0.208 10 false Positive 0.229,2.51 0.979,2.719 0.75,0.208 10 false Negative 0.031,2.844 1.031,3.208 1,0.365 10 false First Reference Pressure 0.448,3.969 0.781,4.135 0.333,0.167 10 false Step 0.125,4.281 1.146,4.49 1.021,0.208 10 false Time (Seconds) 0.25,4.49 1.063,4.698 0.813,0.208 10 false (Reference) 1.615,4.302 1.823,4.51 0.208,0.208 10 false 60 3.698,2.229 4.635,2.438 0.938,0.208 10 false Gross Leak 3.698,2.979 4.635,3.188 0.938,0.208 10 false Small Leak 4.104,3.542 4.833,3.75 0.729,0.208 10 false No Leak 3.323,4.292 4.75,4.458 1.427,0.167 10 false Within 15 minutes 2.469,4.302 2.75,4.5 0.281,0.198 10 false 360 5.104,4.292 5.313,4.5 0.208,0.208 10 false 10 5.667,4.292 5.885,4.5 0.219,0.208 10 false 60 5.135,3.688 6.323,4 1.188,0.313 10 true Normal Pressure 5.094,4.031 5.354,4.24 0.26,0.208 10 false 4/6 5.646,4.031 5.917,4.24 0.271,0.208 10 false 5/6 3.813,4.031 4.188,4.24 0.375,0.208 10 false 3/6 2.49,4.031 2.865,4.24 0.375,0.208 10 false 2/6 1.625,4.031 2,4.24 0.375,0.208 10 false 1/6 3.865,1.51 4.25,1.719 0.385,0.208 10 false ON 3.865,1 4.25,1.208 0.385,0.208 10 false ON 5.073,0.458 5.458,0.667 0.385,0.208 10 false ON 5.646,0.344 6.583,0.563 0.938,0.219 10 false ON: Open 6.24,0.708 7.125,0.927 0.885,0.219 10 false OFF: Closed 5.677,0.917 6.615,1.135 0.938,0.219 10 false ON: Closed 6.323,1.26 7.063,1.479 0.74,0.219 10 false OFF: Vent 0.052,0.031 1.958,0.24 1.906,0.208 10 false EVAP System Check: 6.552,4.031 6.813,4.24 0.26,0.208 10 false 6/6 6.156,3.052 7.146,3.573 0.99,0.521 10 false [Second Reference Pressure] x 0.2

NOTICE:
·

In the Evaporative System Check (Manual Mode), perform the series of 6 Evaporative System Check steps manually using the Techstream.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Manual Mode.



NEXT

4.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6)
4.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6)
U115320E02
0.969,3.146 1.104,3.406 false 1.76,2.979 1.656,2.583 false 1.958,1.938 1.76,2.292 false 0.354,0.563 1.167,0.771 0.813,0.208 10 false Purge VSV 0.385,1.052 1.167,1.271 0.781,0.219 10 false Vent Valve 0.167,1.406 1.177,1.75 1.01,0.344 10 false Leak Detection Pump 0.115,1.948 1.208,2.156 1.094,0.208 10 false EVAP Pressure 0.208,2.198 0.938,2.406 0.729,0.208 10 false Positive 0.208,2.542 0.948,2.75 0.74,0.208 10 false Negative 0.063,2.917 1.063,3.281 1,0.365 10 false First Reference Pressure 1.677,3 2.031,3.208 0.354,0.208 10 false OK 2,1.792 4.042,2.177 2.042,0.385 10 true Canister Pressure Sensor Noise 1.635,4.323 1.844,4.51 0.208,0.188 10 false 60 3.896,1.51 4.292,1.719 0.396,0.208 10 false ON 3.906,1.021 4.302,1.229 0.396,0.208 10 false ON 5.073,0.49 5.469,0.698 0.396,0.208 10 false ON 1.604,3.927 1.938,4.135 0.333,0.208 10 false 1/6 0.292,3.927 0.74,4.135 0.448,0.208 10 false Step 0.146,4.208 1.167,4.417 1.021,0.208 10 false Time (Seconds) 0.292,4.469 1.115,4.677 0.823,0.208 10 false (Reference) 5.677,0.396 6.74,0.615 1.063,0.219 10 false ON: Open 6.198,0.719 7.063,0.927 0.865,0.208 10 false OFF: Closed 5.635,0.927 6.635,1.135 1,0.208 10 false ON: Closed 6.188,1.26 6.917,1.469 0.729,0.208 10 false OFF: Vent

a.

Check the EVAP pressure in step 1/6.

Result
DTC*1 Test Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure Not yet determined A
P0451 EVAP pressure fluctuates by 0.3 kPa-g (2.25 mmHg-g) or more Canister pressure sensor noise B
(P0452 or P0453)*2
·

EVAP pressure is below 42.1 kPa-a (315.85 mmHg-a) or 123.8 kPa-a (928.28 mmHg-a) or more

·

EVAP pressure deviates 10 kPa (75 mmHg) from actual atmosphere pressure *3


Canister pressure sensor or its circuit has malfunction C

·

*1: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.

·

*2: If the canister pressure sensor circuit has an open or short, DTC P0452 or P0453 is stored 0.5 seconds after the ignition switch is turned to ON.


HINT:

*3: Canister pressure sensor standard output range is 70 to 110 kPa-a (525 to 825 mmHg-a). This varies by weather.




A

5.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6 TO 2/6)

B

38.REPAIR CANISTER PUMP MODULE

C

12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT)
5.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6 TO 2/6)
U151389E02
0.979,3.156 1.115,3.417 false 2.667,2.75 2.26,3.458 false 0.375,0.583 1.125,0.802 0.75,0.219 10 false Purge VSV 0.417,1 1.135,1.208 0.719,0.208 10 false Vent Valve 0.177,1.313 1.146,1.688 0.969,0.375 10 false Leak Detection Pump 0.125,1.865 1.219,2.073 1.094,0.208 10 false EVAP Pressure 0.25,2.156 0.896,2.365 0.646,0.208 10 false Positive 0.25,2.521 0.958,2.729 0.708,0.208 10 false Negative 0.052,2.917 1.052,3.333 1,0.417 10 false First Reference Pressure 0.448,3.917 0.813,4.104 0.365,0.188 10 false Step 0.104,4.25 1.115,4.458 1.01,0.208 10 false Time (Seconds) 0.281,4.469 1.115,4.677 0.833,0.208 10 false (Reference) 1.615,4.292 1.844,4.5 0.229,0.208 10 false 60 1.615,3.958 1.979,4.177 0.365,0.219 10 false 1/6 2.51,3.958 2.896,4.177 0.385,0.219 10 false 2/6 2.708,2.646 4.76,3.021 2.052,0.375 10 true Leak Detection Pump Stuck ON 3.833,1.49 4.198,1.698 0.365,0.208 10 false ON 3.833,1.021 4.198,1.229 0.365,0.208 10 false ON 5.083,0.469 5.448,0.677 0.365,0.208 10 false ON 6.219,0.365 6.906,0.573 0.688,0.208 10 false ON: Open 6.219,0.719 7.083,0.927 0.865,0.208 10 false OFF: Closed 6.219,0.917 7.094,1.125 0.875,0.208 10 false ON: Closed 6.219,1.25 7.01,1.458 0.792,0.208 10 false OFF: Vent 2.49,4.292 2.813,4.479 0.323,0.188 10 false 360

a.

Check the EVAP pressure in steps 1/6 and 2/6.

Result
DTC* Test Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure during step 1/6. Then decreases to reference pressure. Not yet determined A
P2402 Small difference between EVAP pressures during steps 1/6 and 2/6 Leak detection pump stuck ON B

*: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.


HINT:

The first reference pressure is the value determined in step 2/6.




A

6.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6)

B

33.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
6.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6)
U151391E02
0.979,3.156 1.115,3.417 false 3.729,3.177 3.229,3.354 false 3.198,2.646 2.844,2.698 false 3.125,1.802 2.667,2.427 false 2,2.073 2.292,1.781 false 3.469,3.875 2.99,3.875 false 0.302,0.563 1.052,0.792 0.75,0.229 10 false Purge VSV 0.417,0.979 1.156,1.188 0.74,0.208 10 false Vent Valve 0.177,1.302 1.198,1.688 1.021,0.385 10 false Leak Detection Pump 0.115,1.854 1.156,2.063 1.042,0.208 10 false EVAP Pressure 0.198,2.146 1.052,2.354 0.854,0.208 10 false Positive 0.198,2.5 1.052,2.708 0.854,0.208 10 false Negative 0.115,2.802 1.104,3.146 0.99,0.344 10 false First Reference Pressure 1.417,2.063 2.271,2.271 0.854,0.208 10 false 4 seconds 2.573,4.063 2.958,4.281 0.385,0.219 10 false 2/6 3.844,4.083 4.156,4.26 0.313,0.177 10 false 3/6 3.469,4.302 4.896,4.51 1.427,0.208 10 false Within 15 minutes 2.479,4.302 2.813,4.51 0.333,0.208 10 false 360 0.354,3.99 0.719,4.198 0.365,0.208 10 false Step 0.281,4.469 1.167,4.677 0.885,0.208 10 false (Reference) 0.115,4.25 1.135,4.458 1.021,0.208 10 false Time (Seconds) 3.781,3.094 4.177,3.302 0.396,0.208 10 false OK 3.292,2.573 4.896,2.792 1.604,0.219 10 false Vent Valve Stuck Closed 3.125,1.781 5.229,2.417 2.104,0.635 10 true Leak Detection Pump Stuck OFF Reference Orifice High-flow 3.854,1.469 4.208,1.677 0.354,0.208 10 false ON 3.854,0.99 4.208,1.198 0.354,0.208 10 false ON 5.073,0.448 5.427,0.656 0.354,0.208 10 false ON 6.24,0.344 6.917,0.552 0.677,0.208 10 false ON: Open 6.24,0.708 7.083,0.927 0.844,0.219 10 false OFF: Closed 6.24,1.25 6.948,1.479 0.708,0.229 10 false OFF: Vent 6.24,0.906 7,1.125 0.76,0.219 10 false ON: Closed 3.531,3.833 5.271,4.01 1.74,0.177 10 true Reference Orifice Clogged

HINT:

Make a note of the pressures observed in steps (a) and (b) below.


(a) Check the EVAP pressure 4 seconds after the leak detection pump is activated*.

*: The leak detection pump begins to operate as step 1/6 finishes and step 2/6 starts.

(b) Check the EVAP pressure again when it has stabilized. This pressure is the reference pressure.

Result
DTC* Test Result Suspected Trouble Area Proceed to
- EVAP pressure in step (b) between -4.85 kPa-g and -1.057 kPa-g (-36.4 mmHg-g and -7.93 mmHg-g) Not yet determined A
P043F and P2401 EVAP pressure in step (b) -1.057 kPa-g (-7.93 mmHg-g) or higher
·

Reference orifice high-flow

·

Leak detection pump stuck OFF


B
P043E EVAP pressure in step (b) below -4.85 kPa-g (-36.4 mmHg-g) Reference orifice clogged C
P2419 EVAP pressure in step (a) higher than -0.25 kPa-g (-1.88 mmHg-g)
·

Vent valve stuck closed

·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)


D

*: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.



A

7.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6 TO 3/6)

B

11.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)

C

38.REPAIR CANISTER PUMP MODULE

D

13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
7.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6 TO 3/6)
U115323E02
0.969,3.135 1.104,3.406 false 3.438,2.719 3.052,3.427 false 0.354,0.583 1.146,0.792 0.792,0.208 10 false Purge VSV 0.396,1.01 1.156,1.219 0.76,0.208 10 false Vent Valve 0.167,1.323 1.208,1.719 1.042,0.396 10 false Leak Detection Pump 0.125,1.865 1.208,2.073 1.083,0.208 10 false EVAP Pressure 0.271,2.125 0.969,2.333 0.698,0.208 10 false Positive 0.25,2.521 1.042,2.729 0.792,0.208 10 false Negative 0.031,2.906 1.031,3.271 1,0.365 10 false First Reference Pressure 0.365,4 0.719,4.208 0.354,0.208 10 false Step 0.719,4.229 1.177,4.438 0.458,0.208 10 false Time 0.229,4.458 1.052,4.677 0.823,0.219 10 false (Reference) 3.823,1.01 4.208,1.219 0.385,0.208 10 false ON 3.813,1.521 4.198,1.729 0.385,0.208 10 false ON 5.073,0.479 5.458,0.688 0.385,0.208 10 false ON 6.292,0.344 7,0.552 0.708,0.208 10 false ON: Open 6.271,0.927 7.083,1.135 0.813,0.208 10 false ON: Closed 6.271,0.708 7.115,0.917 0.844,0.208 10 false OFF: Closed 6.333,1.271 7.094,1.479 0.76,0.208 10 false OFF: Vent 3.49,2.583 4.698,3.042 1.208,0.458 10 false Vent Valve Stuck Open (vent) 3.781,4.01 4.094,4.219 0.313,0.208 10 false 3/6 2.479,4.031 2.802,4.24 0.323,0.208 10 false 2/6 3.406,4.323 4.896,4.531 1.49,0.208 10 false Within 15 minutes

a.

Check the EVAP pressure increase in step 3/6.

Result
DTC* Test Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 2/6 to step 3/6 Not yet determined A
P2420 No variation in EVAP pressure despite proceeding from step 2/6 to step 3/6
·

Vent valve stuck open (vent)

·

Canister (charcoal filter inside canister) clogged


B
P0451 No variation in EVAP pressure during steps 1/6 through 3/6
·

Canister pressure sensor output value stuck

·

Vent valve broken (valve split in two)

·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)


C

*: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.




A

8.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)

B

27.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)

C

15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
8.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)
U115324E02
0.969,3.135 1.104,3.396 false 0.354,0.552 1.073,0.76 0.719,0.208 10 false Purge VSV 0.406,1.094 1.146,1.313 0.74,0.219 10 false Vent Valve 0.167,1.448 1.188,1.823 1.021,0.375 10 false Leak Detection Pump 0.083,1.958 1.167,2.167 1.083,0.208 10 false EVAP Pressure 0.208,2.24 0.896,2.448 0.688,0.208 10 false Positive 0.208,2.542 0.979,2.75 0.771,0.208 10 false Negative 0.021,2.927 1.042,3.302 1.021,0.375 10 false First Reference Pressure 0.354,4.021 0.719,4.229 0.365,0.208 10 false Step 0.781,4.146 1.177,4.354 0.396,0.208 10 false Time 0.365,4.417 1.188,4.625 0.823,0.208 10 false (Reference) 3.854,1.01 4.219,1.219 0.365,0.208 10 false ON 3.854,1.521 4.219,1.729 0.365,0.208 10 false ON 5.073,0.458 5.438,0.667 0.365,0.208 10 false ON 6.26,0.354 6.969,0.563 0.708,0.208 10 false ON: Open 6.26,0.708 7.135,0.917 0.875,0.208 10 false OFF: Closed 6.26,0.927 7.042,1.135 0.781,0.208 10 false ON: Closed 6.333,1.271 7.063,1.479 0.729,0.208 10 false OFF: Vent 3.823,4.052 4.156,4.26 0.333,0.208 10 false 3/6 3.417,4.302 4.771,4.51 1.354,0.208 10 false Within 15 minutes

a.

Wait until the EVAP pressure change over 40 seconds is less than 0.1 kPa-g (0.75 mmHg-g).


b.

Measure the EVAP pressure and record it.

HINT:

A few minutes are required for the EVAP pressure to become stable. When there is little fuel in the fuel tank, it may take up to 15 minutes.




NEXT

9.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 4/6)
9.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 4/6)
U115325E02
0.969,3.135 1.104,3.396 false 4.677,2.094 5.177,2.729 false 4.719,3.031 5.167,3.688 false 0.396,0.552 1.156,0.729 0.76,0.177 10 false Purge VSV 0.396,1.125 1.188,1.344 0.792,0.219 10 false Vent Valve 0.156,1.406 1.125,1.771 0.969,0.365 10 false Leak Detection Pump 0.115,1.906 1.219,2.115 1.104,0.208 10 false EVAP Pressure 0.198,2.188 1.083,2.396 0.885,0.208 10 false Positive 0.198,2.521 1.146,2.729 0.948,0.208 10 false Negative 0.354,3.823 1.042,4.031 0.688,0.208 10 false Step 3.125,2.802 4.729,2.99 1.604,0.188 10 false Purge VSV Stuck Closed 5.063,0.49 5.417,0.698 0.354,0.208 10 false ON 3.896,1.021 4.25,1.229 0.354,0.208 10 false ON 3.906,1.531 4.26,1.74 0.354,0.208 10 false ON 0.125,4.24 1.198,4.448 1.073,0.208 10 false Time (Seconds) 0.302,4.479 1.177,4.688 0.875,0.208 10 false (Reference) 4.427,1.917 4.802,2.125 0.375,0.208 10 false OK 5.094,3.823 5.438,4.031 0.344,0.208 10 false 4/6 5.104,4.323 5.406,4.51 0.302,0.188 10 false 10 5.667,0.354 6.604,0.563 0.938,0.208 10 false ON: Open 5.667,0.927 6.677,1.135 1.01,0.208 10 false ON: Closed 6.198,0.719 7.073,0.927 0.875,0.208 10 false OFF: Closed 6.292,1.26 7.073,1.469 0.781,0.208 10 false OFF: Vent 0.052,2.917 1.073,3.26 1.021,0.344 10 false First Reference Pressure

a.

Check the EVAP pressure in step 4/6.

Result
DTC*1 Test Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6 Not yet determined A
P0441*2 EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6
·

Purge VSV

·

Purge VSV circuit

·

Problems in EVAP hose between purge VSV and intake manifold

·

Problems in EVAP hose between canister and purge VSV

·

ECM


B
P0441 Variation in EVAP pressure less than 0.3 kPa-g (2.25 mmHg-g) for 10 seconds after proceeding from step 3/6 to step 4/6
·

Purge VSV stuck closed

·

Purge VSV circuit

·

Canister (charcoal filter inside canister) clogged

·

Problems in EVAP hose between purge VSV and intake manifold

·

Problems in EVAP hose between canister and purge VSV

·

ECM


C

·

*1: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.

·

*2: This result suggests that due to purge line blockage or purge VSV malfunction, the DTC was stored by the purge flow monitor while the engine was running, or that key-off monitor test result were nearly borderline values.




A

10.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 5/6)

B

22.INSPECT EVAP HOSE (PURGE VSV - CANISTER)

C

17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
10.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 5/6)
U151710E02
6.292,3.844 6.156,3.729 false 6.094,2.708 5.938,2.885 false 0.938,3.302 1.094,3.469 false 0.313,0.563 1.135,0.76 0.823,0.198 10 false Purge VSV 0.375,1.052 1.115,1.24 0.74,0.188 10 false Vent Valve 0.135,1.417 1.125,1.75 0.99,0.333 10 false Leak Detection Pump 0.063,1.896 1.115,2.104 1.052,0.208 10 false EVAP Pressure 0.354,2.146 0.958,2.333 0.604,0.188 10 false Positive 0.292,2.542 0.927,2.74 0.635,0.198 10 false Negative 0.094,3.052 1.135,3.417 1.042,0.365 10 false First Reference Pressure 0.271,3.927 0.729,4.115 0.458,0.188 10 false Step 0.031,4.146 1.135,4.344 1.104,0.198 10 false Time (Seconds) 0.135,4.448 0.958,4.615 0.823,0.167 10 false (Reference) 5.073,0.5 5.427,0.688 0.354,0.188 10 false ON 3.771,1.021 4.125,1.208 0.354,0.188 10 false ON 3.771,1.531 4.125,1.719 0.354,0.188 10 false ON 3.573,2.26 4.354,2.448 0.781,0.188 10 false Gross Leak 3.656,3 4.438,3.208 0.781,0.208 10 false Small Leak 4.125,3.583 4.74,3.75 0.615,0.167 10 false No Leak 6.156,2.531 7.135,3.135 0.979,0.604 10 false [Second Reference Pressure] x 0.2 6.271,1.26 7.042,1.479 0.771,0.219 10 false OFF: Vent 6.229,0.938 7.063,1.125 0.833,0.188 10 false ON: Closed 6.365,0.302 7.073,0.51 0.708,0.208 10 false ON: Open 6.219,0.719 7.094,0.906 0.875,0.188 10 false OFF: Closed 6.365,3.823 7.052,4.344 0.688,0.521 10 true [Second Reference Pressure] 5.646,4.073 5.906,4.24 0.26,0.167 10 false 5/6 5.667,4.302 5.958,4.51 0.292,0.208 10 false 60

a.

Check the EVAP pressure in step 5/6.


b.

Compare the EVAP pressure from step 3/6 and the second reference pressure (step 5/6).

Result
DTC* Test Result Suspected Trouble Area Proceed to
- EVAP pressure (step 3/6) lower than second reference pressure (step 5/6) Not yet determined (no leakage from EVAP system) A
P0441 and P0455 EVAP pressure (step 3/6) higher than [second reference pressure (step 5/6) x 0.2]
·

Purge VSV stuck open

·

EVAP gross leak


B
P0456 EVAP pressure (step 3/6) higher than second reference pressure (step 5/6) EVAP small leak B

*: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.




A

43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS

B

17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
11.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6)
U113559E03
0.979,3.156 1.115,3.417 false 3.781,1.875 3.417,2.438 false 3.625,2.781 3.323,3.042 false 5.073,0.469 5.469,0.677 0.396,0.208 10 false ON 3.844,1 4.24,1.208 0.396,0.208 10 false ON 3.844,1.51 4.24,1.719 0.396,0.208 10 false ON 3.833,1.781 5.219,2.156 1.385,0.375 10 true Leak Detection Pump Stuck OFF 3.677,2.646 4.813,3.042 1.135,0.396 10 false Reference Orifice High-flow 3.5,4.333 4.813,4.531 1.313,0.198 10 false Within 15 minutes 3.875,3.99 4.198,4.208 0.323,0.219 10 false 3/6 2.479,3.99 2.792,4.198 0.313,0.208 10 false 2/6 0.354,0.583 1.115,0.792 0.76,0.208 10 false Purge VSV 0.354,0.969 1.146,1.177 0.792,0.208 10 false Vent Valve 0.156,1.344 1.125,1.719 0.969,0.375 10 false Leak Detection Pump 0.063,1.844 1.198,2.052 1.135,0.208 10 false EVAP Pressure 0.208,2.135 0.906,2.344 0.698,0.208 10 false Positive 0.198,2.521 0.948,2.729 0.75,0.208 10 false Negative 0.063,2.938 1.073,3.333 1.01,0.396 10 false First Reference Pressure 0.375,3.958 0.74,4.167 0.365,0.208 10 false Step 0.75,4.156 1.177,4.365 0.427,0.208 10 false Time 0.333,4.427 1.188,4.646 0.854,0.219 10 false (Reference) 6.25,0.344 6.948,0.552 0.698,0.208 10 false ON: Open 6.25,0.906 7.021,1.115 0.771,0.208 10 false ON: Closed 6.24,0.708 7.104,0.917 0.865,0.208 10 false OFF: Closed 6.25,1.26 7,1.469 0.75,0.208 10 false OFF: Vent

a.

Check the EVAP pressure in step 3/6.

Result
DTC* Test Result Suspected Trouble Area Proceed to
P043F EVAP pressure less than [reference pressure] measured in step 2/6 Reference orifice high-flow A
P2401 EVAP pressure almost same as [reference pressure] measured in step 2/6 Leak detection pump stuck OFF B

*: These DTCs are already stored in the ECM when the vehicle arrives and are confirmed in the Confirm DTC procedures above.


HINT:

The first reference pressure is the value determined in step 2/6.




A

38.REPAIR CANISTER PUMP MODULE

B

31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT)
a.

Check the canister pressure sensor circuit, referring to DTC P0451 canister pressure sensor circuit inspection procedure (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0451).



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
A287416E09
2.083,0.229 1.656,0.563 false 2.073,0.698 1.74,0.583 false 2.115,0.104 2.792,0.344 0.677,0.24 10 false VLVB (+) 2.115,0.635 2.813,0.854 0.698,0.219 10 false VGND (-) 0.125,0.063 0.281,0.24 0.156,0.177 10 false *a

a.

Turn the ignition switch off.


b.

Disconnect the R12 canister pump module connector.


c.

Apply battery voltage to the VLVB and VGND terminals of the canister pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Condition Tester Result Suspected Trouble Area Proceed to
Apply battery voltage to terminals VLVB and VGND Operating
·

Wire harness or connector between vent valve and ECM

·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)

·

ECM


A
Not operating Vent valve B

Text in Illustration
*a Component without harness connected
(Canister Pump Module)



A

14.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)

B

38.REPAIR CANISTER PUMP MODULE
14.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
a.

Disconnect the ECM connector.


b.

Disconnect the canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (VPMP) - R12-1 (VGND) Always Below 1 Ω
A24-30 (VPMP) or R12-1 (VGND) - Body ground Always 10 kΩ or higher


Result
Result Suspected Trouble Area Proceed to
OK
·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)

·

ECM


A
NG Wire harness or connector between ECM and canister pump module B



A

15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
a.

Disconnect the canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.


Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
R12-4 (MGND) - Body ground Always Below 1 Ω
·

Canister pump module

·

Wire harness or connector between canister pump module and ECM

·

ECM


A
10 kΩ or higher Wire harness or connector between canister pump module and body ground B


A

16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-49 (MPMP) - R12-3 (MTRB) Always Below 1 Ω
A24-49 (MPMP) or R12-3 (MTRB) - Body ground Always 10 kΩ or higher



Result
Result Suspected Trouble Area Proceed to
OK
·

Canister pump module

·

ECM


A
NG Wire harness or connector between ECM and canister pump module B


A

45.REPLACE CANISTER PUMP MODULE

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
a.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.


b.
A214696E05
0.601,0.366 0.827,0.529 0.225,0.163 10 *1 1.871,2.759 2.096,2.943 0.225,0.184 10 *2 1.121,0.443 1.76,1.4 false 2.508,2.25 2.3,2.847 false 0.815,0.443 1.121,0.443 false 2.078,2.843 2.307,2.843 false

Disconnect the hose (connected to the canister) from the purge VSV.


c.

Start the engine.


d.

Using the Techstream, turn off the purge VSV (Activate the VSV for EVAP Control: OFF).


e.

Use your finger to confirm that the purge VSV has no suction.


f.

Using the Techstream, turn on the purge VSV (Activate the VSV for EVAP Control: ON).


g.

Use your finger to confirm that the purge VSV has suction.

Result
Test Result Suspected Trouble Area Proceed to
No suction when purge VSV turned OFF, and suction applied when turned ON Blockage in the purge line is considered (based on result of step 9):
·

Problems with EVAP hose between canister and purge VSV

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Leakage is considered (based on result of step 10):
·

Fuel cap

·

Leakage from EVAP line, fuel tank, or canister assembly


B
Suction applied when purge VSV turned OFF Purge VSV stuck open C
No suction when purge VSV turned ON
·

Purge VSV stuck closed

·

Problems with EVAP hose between purge VSV and intake manifold


D

Text in Illustration
*1 Purge VSV
*2 Hose (to Canister)



A

18.INSPECT EVAP HOSE (PURGE VSV - CANISTER)

B

20.CHECK FUEL TANK CAP ASSEMBLY

C

21.INSPECT PURGE VSV

D

23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)
18.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
a.

Check for blockages in the EVAP purge line between the purge VSV and canister.

OK:

No blockages in the EVAP purge line between the purge VSV and canister.




OK

19.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)

NG

44.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER)
19.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)
a.

Check for filter blockage in the canister assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>INSPECTION).

OK:

No blockages in the canister assembly.




OK

47.REPLACE ECM

NG

48.REPLACE CANISTER ASSEMBLY
20.CHECK FUEL TANK CAP ASSEMBLY
a.

Check that the fuel tank cap is correctly installed and confirm that the fuel tank cap meets OEM specifications.


b.

Tighten the fuel tank cap firmly (only one click sound is heard).

HINT:

If an EVAP tester is available, check the fuel tank cap using the tester.

1.

Remove the fuel tank cap and install it to a fuel tank cap adapter.

2.

Connect an EVAP tester pump hose to the adapter, and pressurize the fuel tank cap to between 3.2 and 3.7 kPa (24 and 28 mmHg) using an EVAP tester pump.

3.

Seal the adapter and wait for 2 minutes.

4.

Check the pressure. If the pressure is 2 kPa (15 mmHg) or higher, the fuel tank cap is normal.



Result
Test Result Suspected Trouble Area Proceed to
Fuel tank cap correctly installed - A
Fuel tank cap loose
·

Fuel tank cap improperly installed

·

Defective fuel tank cap

·

Fuel tank cap does not meet OEM specifications


B
Defective fuel tank cap - B
No fuel tank cap - C



A

37.LOCATE EVAP PART WHICH IS LEAKING

B

35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY

C

36.REPLACE FUEL TANK CAP ASSEMBLY
21.INSPECT PURGE VSV
a.

Turn the ignition switch off.


b.

Disconnect the purge VSV connector.


c.
A214697E04
0.861,0.47 1.048,0.633 0.187,0.163 10 *1 2.034,2.699 2.263,2.883 0.229,0.184 10 *2 1.212,0.553 1.826,1.366 false 2.531,2.174 2.339,2.787 false 1.047,0.557 1.216,0.557 false 2.231,2.783 2.339,2.783 false

Disconnect the hose (connected to the canister) from the purge VSV.


d.

Start the engine.


e.

Use your finger to confirm that the purge VSV has no suction.

Result
Test Result Suspected Trouble Area Proceed to
No suction
·

Wire harness or connector between purge VSV and ECM (short to ground)

·

ECM


A
Suction applied Purge VSV B

Text in Illustration
*1 Purge VSV
*2 Hose (to Canister)
*3 Connector



A

26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

B

39.REPLACE PURGE VSV
22.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
a.

Check for blockages in the EVAP purge line between the purge VSV and canister.

OK:

No blockages in the EVAP purge line between the purge VSV and canister.




OK

23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)

NG

44.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER)
23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)
a.
A214698E05
0.65,0.265 0.864,0.428 0.215,0.163 10 *1 1.242,2.723 1.469,2.907 0.227,0.184 10 *2 1.053,0.343 1.76,1.4 false 0.784,2.036 1.042,2.822 false 1.042,2.822 1.202,2.822 false 0.862,0.347 1.053,0.347 false

Disconnect the hose (connected to the intake manifold) from the purge VSV.


b.

Start the engine.


c.

Use your finger to confirm that the hose has suction.

Result
Test Result Suspected Trouble Area Proceed to
Suction applied EVAP hose between purge VSV and intake manifold normal
·

Purge VSV

·

Purge VSV power source

·

Wire harness or connector between purge VSV and ECM


A
No suction
·

Intake manifold port

·

EVAP hose between purge VSV and intake manifold


B

Text in Illustration
*1 Purge VSV
*2 Hose (to Intake Manifold)



A

24.INSPECT PURGE VSV

B

34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
24.INSPECT PURGE VSV
A218158E02
0.063,0.003 0.239,0.186 0.177,0.183 10 *1 1.481,1.108 1.657,1.290 0.177,0.183 10 *2 0.198,0.825 0.374,1.008 0.177,0.183 10 *3

a.

Remove the purge VSV.


b.

Apply battery voltage to the terminals of the purge VSV.


c.

Using an air gun, confirm that air flows from port A to port B.

Result
Test Result Condition Suspected Trouble Area Proceed to
Air flows Battery voltage is applied to purge VSV terminals Purge VSV normal
·

Purge VSV power source

·

Wire harness or connector between purge VSV and ECM


A
No air flow Battery voltage is applied to purge VSV terminals Purge VSV B

Text in Illustration
*1 Purge VSV
*2 Port A
*3 Port B



A

25.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)

B

39.REPLACE PURGE VSV
25.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)
U151380E02
0.177,0.021 2.563,0.406 2.385,0.385 10 false *a 0.615,1.031 0.958,1.229 0.344,0.198 10 false D29

a.

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Switch Condition Specified Condition Suspected Trouble Area Proceed to
D29-1 - Body ground Ignition switch ON 11 to 14 V Purge VSV power source normal
·

Wire harness or connector between purge VSV and ECM


A
Ignition switch ON Other than result above Wire harness or connectors between purge VSV and battery B


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)



A

26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the purge VSV connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-63 (PRG) - D29-2 Always Below 1 Ω
D74-63 (PRG) or D29-2 - Body ground Always 10 kΩ or higher




OK

47.REPLACE ECM

NG

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
27.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)
U151754E01
4.279,0.033 4.456,0.228 0.177,0.195 10 *a 4.802,2.083 5.347,2.239 0.545,0.156 10 VLVB 4.987,2.055 5.405,1.504 false 5.521,0.62 5.820,0.790 0.299,0.170 10 R12

a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Switch Condition Specified Condition Suspected Trouble Area Proceed to
R12-5 (VLVB) - Body ground Ignition switch ON 11 to 14 V
·

Wire harness or connector between vent valve and ECM

·

Vent valve

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Ignition switch ON Below 3 V Power source wire harness of vent valve B


Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)



A

28.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
28.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
A287416E09
2.083,0.229 1.656,0.563 false 2.073,0.698 1.74,0.583 false 2.115,0.104 2.792,0.344 0.677,0.24 10 false VLVB (+) 2.115,0.635 2.813,0.854 0.698,0.219 10 false VGND (-) 0.125,0.063 0.281,0.24 0.156,0.177 10 false *a

a.

Turn the ignition switch off.


b.

Disconnect the R12 canister pump module connector.


c.

Apply battery voltage to the VLVB and VGND terminals of the canister pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Condition Tester Result Suspected Trouble Area Proceed to
Apply battery voltage to terminals VLVB and VGND Operating
·

Wire harness or connector between vent valve and ECM

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Not operating Vent valve B

Text in Illustration
*a Component without harness connected
(Canister Pump Module)



A

29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

38.REPAIR CANISTER PUMP MODULE
29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-30 (VPMP) - R12-1 (VGND) Always Below 1 Ω
A24-30 (VPMP) or R12-1 (VGND) - Body ground Always 10 kΩ or higher


Result
Result Suspected Trouble Area Proceed to
OK
·

Canister (charcoal filter inside canister) clogged

·

ECM


A
NG Wire harness or connector between ECM and canister pump module B



A

30.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
30.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)
a.

Check for filter blockage in the canister assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>INSPECTION).

OK:

No blockages in the canister assembly.




OK

47.REPLACE ECM

NG

48.REPLACE CANISTER ASSEMBLY
31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
U151755E01
4.366,0.06 4.542,0.255 0.177,0.195 10 *a 6.257,1.97 6.691,2.126 0.434,0.156 10 MTRB 5.751,1.375 6.203,1.958 false 5.551,0.605 5.850,0.775 0.299,0.170 10 R12

a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
R12-3 (MTRB) - Body ground Ignition switch ON 9 to 14 V
·

Wire harness or connector between leak detection pump and body ground

·

Leak detection pump


A
Below 3 V
·

Wire harness or connector between leak detection pump and ECM

·

ECM


B


Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)



A

32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)

B

33.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
R12-4 (MGND) - Body ground Always Below 1 Ω Leak detection pump A
Always 10 kΩ or higher Wire harness or connector between canister pump module and body ground B




A

38.REPAIR CANISTER PUMP MODULE

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
33.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Disconnect the canister pump module connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-49 (MPMP) - R12-3 (MTRB) Always Below 1 Ω
A24-49 (MPMP) or R12-3 (MTRB) - Body ground Always 10 kΩ or higher



Result
Result Suspected Trouble Area Proceed to
OK ECM A
NG Wire harness or connector between ECM and canister pump module B


A

47.REPLACE ECM

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
a.

Stop the engine.


b.

Disconnect the EVAP hose from the intake manifold.


c.

Start the engine.


d.

Use your finger to confirm that the port of the intake manifold has suction.


Result
Test Result Suspected Trouble Area Proceed to
Suction applied EVAP hose between intake manifold and purge VSV A
No suction Intake manifold B


A

41.REPAIR OR REPLACE EVAP PURGE LINE (INTAKE MANIFOLD - PURGE VSV)

B

42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY
HINT:
·

When reinstalling the fuel tank cap, tighten it until a click sound is heard.

·

When replacing the fuel tank cap, use a fuel tank cap that meets OEM specifications and tighten it until a click sound is heard.




NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
36.REPLACE FUEL TANK CAP ASSEMBLY
HINT:

When replacing the fuel tank cap, use a fuel tank cap that meets OEM specifications and tighten it until a click sound is heard.



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
37.LOCATE EVAP PART WHICH IS LEAKING
A292303E01
0.784,3.647 1.002,3.830 0.218,0.184 10 *1 2.157,3.647 2.375,3.830 0.218,0.184 10 *2 4.493,2.112 4.712,2.296 0.218,0.184 10 *3 4.286,2.038 4.381,2.189 false 4.381,2.189 4.476,2.189 false

Text in Illustration
*1 EVAP Tester *2 Adapter
*3 Canister Outlet Hose - -

a.

Disconnect the canister outlet hose.


b.

Connect an EVAP tester to the canister pump module with an adapter.


c.

Pressurize the EVAP system to between 3.2 and 3.7 kPa (24 and 28 mmHg).


d.

Apply soapy water to the piping and connecting parts of the EVAP system.


e.

Look for areas where bubbles appear. Bubbles indicate the leak point.


f.

Repair or replace the leak point.

HINT:

Disconnect the hose between the canister and fuel tank from the canister. Block the canister side and conduct an inspection. In this way, the fuel tank can be excluded as an area suspected of causing fuel leaks.




NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
38.REPAIR CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



A289733E10
1.677,2.938 1.479,3.323 1.479,3.323 1.354,3.323 false 3.74,1.708 3.104,3.042 3.104,3.042 2.969,3.042 false 4.771,2.135 4.844,2.375 4.844,2.375 4.938,2.375 false 4.573,4.125 4.792,4.354 4.792,4.354 4.875,4.354 false 5.146,1.448 5.313,1.042 5.313,1.042 5.448,1.042 false 4.01,2.958 4.135,2.792 4.135,2.792 4.24,2.792 false 2.74,2.938 2.948,3.125 0.208,0.188 10 false *2 4.24,2.729 4.427,2.917 0.188,0.188 10 false *6 4.958,2.25 5.146,2.438 0.188,0.188 10 false *4 4.927,4.25 5.146,4.438 0.219,0.188 10 false *5 5.083,2.813 5.271,3 0.188,0.188 10 false *a 3.74,0.813 3.927,1 0.188,0.188 10 false *a 1.135,3.208 1.354,3.396 0.219,0.188 10 false *1 5.5,0.948 5.74,1.115 0.24,0.167 10 false *3

Text in Illustration
*1 Fuel Tank *2 Fuel Tank Vent Hose
*3 Canister Assembly *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *6 Canister Outlet Hose
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
39.REPLACE PURGE VSV

NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
40.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
41.REPAIR OR REPLACE EVAP PURGE LINE (INTAKE MANIFOLD - PURGE VSV)

NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
a.

Check that the EVAP purge port of the intake manifold is not clogged. If necessary, replace the intake manifold.



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
a.

Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
44.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER)

NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
45.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



A289733E10
1.677,2.938 1.479,3.323 1.479,3.323 1.354,3.323 false 3.74,1.708 3.104,3.042 3.104,3.042 2.969,3.042 false 4.771,2.135 4.844,2.375 4.844,2.375 4.938,2.375 false 4.573,4.125 4.792,4.354 4.792,4.354 4.875,4.354 false 5.146,1.448 5.313,1.042 5.313,1.042 5.448,1.042 false 4.01,2.958 4.135,2.792 4.135,2.792 4.24,2.792 false 2.74,2.938 2.948,3.125 0.208,0.188 10 false *2 4.24,2.729 4.427,2.917 0.188,0.188 10 false *6 4.958,2.25 5.146,2.438 0.188,0.188 10 false *4 4.927,4.25 5.146,4.438 0.219,0.188 10 false *5 5.083,2.813 5.271,3 0.188,0.188 10 false *a 3.74,0.813 3.927,1 0.188,0.188 10 false *a 1.135,3.208 1.354,3.396 0.219,0.188 10 false *1 5.5,0.948 5.74,1.115 0.24,0.167 10 false *3

Text in Illustration
*1 Fuel Tank *2 Fuel Tank Vent Hose
*3 Canister Assembly *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *6 Canister Outlet Hose
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

46.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
46.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing an Evaporative System Check, keep the fuel temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


c.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

Result
Result Proceed to
EVAP system DTCs are output A
DTC is not output
(Pending DTC is not output)
B



A

47.REPLACE ECM

B

END

47.REPLACE ECM

NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
48.REPLACE CANISTER ASSEMBLY
a.

Replace the canister assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister, check the canister pump module interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



A289733E10
1.677,2.938 1.479,3.323 1.479,3.323 1.354,3.323 false 3.74,1.708 3.104,3.042 3.104,3.042 2.969,3.042 false 4.771,2.135 4.844,2.375 4.844,2.375 4.938,2.375 false 4.573,4.125 4.792,4.354 4.792,4.354 4.875,4.354 false 5.146,1.448 5.313,1.042 5.313,1.042 5.448,1.042 false 4.01,2.958 4.135,2.792 4.135,2.792 4.24,2.792 false 2.74,2.938 2.948,3.125 0.208,0.188 10 false *2 4.24,2.729 4.427,2.917 0.188,0.188 10 false *6 4.958,2.25 5.146,2.438 0.188,0.188 10 false *4 4.927,4.25 5.146,4.438 0.219,0.188 10 false *5 5.083,2.813 5.271,3 0.188,0.188 10 false *a 3.74,0.813 3.927,1 0.188,0.188 10 false *a 1.135,3.208 1.354,3.396 0.219,0.188 10 false *1 5.5,0.948 5.74,1.115 0.24,0.167 10 false *3

Text in Illustration
*1 Fuel Tank *2 Fuel Tank Vent Hose
*3 Canister Assembly *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *6 Canister Outlet Hose
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing an Evaporative System Check, keep the fuel temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


c.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.

HINT:

If no pending DTCs are found, the repair has been successfully completed.




NEXT

END