Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E02
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.758,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.049,5.101 1.166,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in OCV (for exhaust side of bank 1) circuit
(1 trip detection logic)
·

Open or short in OCV (for exhaust side of bank 1) circuit

·

OCV (for exhaust side of bank 1)

·

ECM


P0023 Open or short in OCV (for exhaust side of bank 2) circuit
(1 trip detection logic)
·

Open or short in OCV (for exhaust side of bank 2) circuit

·

OCV (for exhaust side of bank 2)

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0013: Exhaust camshaft OCV (for Bank 1)
P0023: Exhaust camshaft OCV (for Bank 2)
Required sensors/Components (Main) Exhaust camshaft OCV
Required sensors/Components (Related) -
Frequency of operation Continuous
Duration 1 second
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present None
All of following conditions met -
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

Case 1
One of following conditions met -
A. All of following conditions met -
Battery voltage 11 to 13 V
Target duty ratio Less than 70%
B. All of following conditions met -
Battery voltage 13 V or more
Target duty ratio Less than 80%

Case 2
Current cut status Not cut

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Output duty cycle 100% or more

Case 2
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

OCV duty-cycle 3 to 100%

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0013 or P0023.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162759E27
5.896,4.302 6.385,4.49 0.49,0.188 10 false ECM 0.24,1.813 2.427,2.042 2.188,0.229 10 false OCV (for Exhaust Side of Bank 1) 1.479,0.521 1.844,0.781 0.365,0.26 10 false 1 1.479,1.24 1.771,1.458 0.292,0.219 10 false 2 1.469,2.469 1.833,2.729 0.365,0.26 10 false 1 1.469,3.208 1.76,3.427 0.292,0.219 10 false 2 5.115,0.51 5.385,0.74 0.271,0.229 10 false 56 5.115,1.26 5.385,1.49 0.271,0.229 10 false 55 5.104,3.208 5.375,3.438 0.271,0.229 10 false 49 5.115,2.469 5.385,2.698 0.271,0.229 10 false 50 5.417,0.51 5.865,0.688 0.448,0.177 10 false OE1+ 5.427,1.24 5.813,1.427 0.385,0.188 10 false OE1- 5.417,2.469 5.875,2.677 0.458,0.208 10 false OE2+ 5.427,3.198 5.865,3.385 0.438,0.188 10 false OE2- 5.896,4.125 6.26,4.396 0.365,0.271 10 false D74 0.26,1.656 0.573,1.844 0.313,0.188 10 false D44 0.26,3.604 0.573,3.792 0.313,0.188 10 false D45 0.25,3.76 2.417,3.958 2.167,0.198 10 false OCV (for Exhaust Side of Bank 2)

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0023 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR DTC (DTC P0013 OR P0023)
a.

Connect the Techstream to the DLC3.


b.

Clear DTCs after recording the freeze frame data and DTC.


c.

Turn the ignition switch off.


d.

Allow the engine to idle and check for DTCs.


e.

Check that P0013 or P0023 is not present.

OK:

P0013 or P0023 is not present.




OK

NG

2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
a.
A160397E02
0.059,0 2.561,0.350 2.502,0.350 10 Component without harness connected: (Oil Control Valve)

Disconnect the OCV connector.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω




OK

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)

NG

REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
a.

Disconnect the OCV connector.

A379411E02
0.458,1.25 0.875,1.469 0.417,0.219 0.458,1.552 0.875,1.771 0.417,0.219 3.865,0.76 4.281,0.979 0.417,0.219 4.167,1.479 4.542,0.99 false 4.24,1.479 4.927,0.865 false 4.656,1.469 5.427,2.146 false 4.594,1.479 4.875,2.156 false 0.292,0.083 2.604,0.438 2.313,0.354 10 false Front view of wire harness connector: (to Oil Control Valve) 3.917,0.063 6.229,0.417 2.313,0.354 10 false Front view of wire harness connector: (to ECM) 0.542,1.281 0.896,1.458 0.354,0.177 10 false D44 0.542,1.583 0.896,1.76 0.354,0.177 10 false D45 0.938,1.271 1.188,1.448 0.25,0.177 10 false *1 0.938,1.552 1.188,1.729 0.25,0.177 10 false *2 3.948,0.792 4.302,0.969 0.354,0.177 10 false D74 4.417,0.781 4.854,0.99 0.438,0.208 10 false OE2- 4.979,0.708 5.417,0.917 0.438,0.208 10 false OE2+ 0.25,2.083 1.323,2.271 1.073,0.188 10 false *1: for Bank 1 0.26,2.406 1.333,2.594 1.073,0.188 10 false *2: for Bank 2 4.875,2.188 5.313,2.396 0.438,0.208 10 false OE1- 5.458,2.146 5.896,2.354 0.438,0.208 10 false OE1+


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D44-1 - D74-56 (OE1+) Always Below 1 Ω
D44-2 - D74-55 (OE1-) Always Below 1 Ω
D45-1 - D74-50 (OE2+) Always Below 1 Ω
D45-2 - D74-49 (OE2-) Always Below 1 Ω
D44-1 or D74-56 (OE1+) - Body ground Always 10 kΩ or higher
D44-2 or D74-55 (OE1-) - Body ground Always 10 kΩ or higher
D45-1 or D74-50 (OE2+) - Body ground Always 10 kΩ or higher
D45-2 or D74-49 (OE2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR