Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P106A  Evaporative Emission System Pressure Sensor - Manifold Absolute Pressure Correlation  P106B  Evaporative Emission System Pressure Sensor - Secondary Air Injection Pressure Sensor Correlation  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
P106A The pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the manifold absolute pressure sensor (MAP*) differ by 7 kPa (54 mmHg) or more
(2 trip detection logic)
·

Canister pressure sensor (canister pump module)

·

Manifold absolute pressure sensor


P106B The pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the pressure sensor of either air switching valve (for Bank 1 or Bank 2) (Air Pump Pressure (Absolute)* or Air Pump2 Pressure (Absolute)*) differ by 6.98 kPa (52 mmHg) or more
(2 trip detection logic)
·

Canister pressure sensor (canister pump module)

·

Air switching valve (Bank 1)

·

Air switching valve (Bank 2)



HINT:

*: Name of Data List item


MONITOR DESCRIPTION

This DTC is stored when a deviation from pressure sensor characteristics is detected.

The pressure sensors* are checked 55 minutes after the ignition switch is turned off. If the pressures detected by the pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

HINT:
·

*: P106A checks the canister pressure sensor and manifold absolute pressure sensor. P106B checks the canister pressure sensor and the pressure sensor of the air switching valves (Bank 1 and Bank 2).

·

Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.



MONITOR STRATEGY

Related DTCs P106A: Evaporative emission system pressure sensor - manifold absolute pressure correlation
P106B: Evaporative emission system pressure sensor - secondary air injection system pressure sensor correlation
Required Sensors/Components (Main)
·

Canister pressure sensor

·

Manifold absolute pressure sensor

·

Pressure sensor (Air switching valve (Bank 1 or Bank 2))


Required Sensors/Components (Related) -
Frequency of Operation Once per drive cycle
Duration Less than 65 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P106A:
Monitor runs whenever following DTCs not present P0107, P0108 (Manifold absolute pressure)
P0401 (EGR system)
P0452, P0453 (EVAP system, Evaporative emission system pressure sensor)
Time elapsed after engine stop 50 minutes
Time after ECM started by soak-timer 60 seconds or more
Battery voltage 10.5 V or more
Intake air temperature -10°C (14°F) or more
Engine coolant temperature -10°C (14°F) or more

P106B:
Monitor runs whenever following DTCs not present P0452, P0453 (EVAP system)
P2431, P2432, P2433, P2436, P2437, P2438 (Secondary air injection system pressure sensor)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary air injection system)
Time elapsed after engine stop 50 minutes
Time after ECM started by soak-timer 60 seconds or more
Battery voltage 10.5 V or more
Intake air temperature -10°C (14°F) or more
Engine coolant temperature -10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS

P106A:
Difference between EVAP pressure and manifold absolute pressure More than 7.22 kPa (54 mmHg)

P106B:
Difference between EVAP pressure (Vapor Pressure Pump*) and secondary air pressure sensor (bank 1) (Air Pump Pressure (Absolute)*) More than 6.98 kPa (52 mmHg)
Difference between EVAP pressure (Vapor Pressure Pump*) and secondary air pressure sensor (bank 2) (Air Pump2 Pressure (Absolute)*) More than 6.98 kPa (52 mmHg)

HINT:

*: Name of Data List item


CONFIRMATION DRIVING PATTERN

A215924E13
0.25,1.771 1.458,1.979 1.208,0.208 10 false Ignition Switch ON 1.031,1.229 1.458,1.438 0.427,0.208 10 false Idling 2.781,2.646 3.625,2.854 0.844,0.208 10 false 10 seconds 4.365,2.635 5.146,2.844 0.781,0.208 10 false 55 minutes 2.198,1.885 2.479,2.094 0.281,0.208 10 false [A] 3,1.115 3.281,1.333 0.281,0.219 10 false [B] 4.667,2.094 4.99,2.313 0.323,0.219 10 false [C] 6.052,2.865 6.313,3.073 0.26,0.208 10 false [D]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR) [A].

4.

Start the engine.

5.

Idle the engine for 10 seconds [B].

6.

Turn the ignition switch off.

7.

Soak the vehicle for 55 minutes [C].

8.

Turn the ignition switch ON and turn the Techstream on.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs [D].

11.

If a pending DTC is output, the system is malfunctioning.

HINT:

If no pending DTC is output, perform the steps below.


12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P106A or P106B.

14.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.



15.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P106A, P106B)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P106A is output A
P106B is output B
P106A and P106B are output C
P106A, P106B and other DTCs are output D

HINT:

If any DTCs other than P106A or P106B are output, perform troubleshooting for those DTCs first.




A

2.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

B

3.READ VALUE USING TECHSTREAM (AIR PUMP PRESSURE (ABSOLUTE) AND AIR PUMP2 PRESSURE (ABSOLUTE))

C

6.REPLACE CANISTER PUMP MODULE

D

2.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.READ VALUE USING TECHSTREAM (AIR PUMP PRESSURE (ABSOLUTE) AND AIR PUMP2 PRESSURE (ABSOLUTE))
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Vapor Pressure Pump.


e.

Read the value.

Result
Result Proceed to
Difference between Air Pump Pressure (Absolute) and Vapor Pressure Pump is more than 3.5 kPa (26 mmHg) A
Difference between Air Pump2 Pressure (Absolute) and Vapor Pressure Pump is more than 3.5 kPa (26 mmHg) B



A

4.REPLACE AIR SWITCHING VALVE (FOR BANK 1)

B

5.REPLACE AIR SWITCHING VALVE (FOR BANK 2)
4.REPLACE AIR SWITCHING VALVE (FOR BANK 1)
a.


NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE AIR SWITCHING VALVE (FOR BANK 2)
a.


NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



A289733E10
1.677,2.938 1.479,3.323 1.479,3.323 1.354,3.323 false 3.74,1.708 3.104,3.042 3.104,3.042 2.969,3.042 false 4.771,2.135 4.844,2.375 4.844,2.375 4.938,2.375 false 4.573,4.125 4.792,4.354 4.792,4.354 4.875,4.354 false 5.146,1.448 5.313,1.042 5.313,1.042 5.448,1.042 false 4.01,2.958 4.135,2.792 4.135,2.792 4.24,2.792 false 2.74,2.938 2.948,3.125 0.208,0.188 10 false *2 4.24,2.729 4.427,2.917 0.188,0.188 10 false *6 4.958,2.25 5.146,2.438 0.188,0.188 10 false *4 4.927,4.25 5.146,4.438 0.219,0.188 10 false *5 5.083,2.813 5.271,3 0.188,0.188 10 false *a 3.74,0.813 3.927,1 0.188,0.188 10 false *a 1.135,3.208 1.354,3.396 0.219,0.188 10 false *1 5.5,0.948 5.74,1.115 0.24,0.167 10 false *3

Text in Illustration
*1 Fuel Tank *2 Fuel Tank Vent Hose
*3 Canister Assembly *4 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
*5 Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) *6 Canister Outlet Hose
*a Inspection Area (check for disconnection and/or cracks) - -



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Compare the Data List items Air Pump Pressure (Absolute) and Vapor Pressure Pump, Air Pump2 Pressure (Absolute) and Vapor Pressure Pump, and Vapor Pressure Pump and MAP.


f.

Confirm that the difference between Vapor Pressure Pump and MAP, and between Vapor Pressure Pump, Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute) is 3.5 kPa (26 mmHg) or less.



NEXT

END