Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When either of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A160257E01
2.954,2.753 5.064,2.960 2.110,0.207 10 Temperature Sensor (Thermistor) 1.929,0.681 2.184,0.845 0.255,0.163 10 +B 1.878,1.033 2.969,1.179 1.091,0.145 10 Power Transistor 2.18,1.424 3.342,1.595 1.162,0.171 10 Hot Wire (Heater) 5.974,2.76 7.117,2.932 1.143,0.171 10 Hot Wire (Heater) 1.357,2.631 1.593,1.889 false 2.142,1.492 1.962,1.924 false 2.574,2.013 3.560,2.207 0.986,0.194 10 Output Voltage 4.646,2.733 5.424,1.969 false 6.322,2.003 6.116,2.746 false 1.323,1.911 1.487,2.075 0.164,0.165 10 A 2.133,1.904 2.299,2.072 0.165,0.168 10 B 4.967,3.273 6.151,3.439 1.184,0.165 10 Cold Film Element 0.474,2.638 1.658,2.803 1.184,0.165 10 Cold Film Element 5.507,3.235 5.794,1.968 false

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter voltage is below 0.2 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


P0103 Mass air flow meter voltage is higher than 4.9 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM



HINT:

When either of these DTCs is stored, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/sec.) Malfunction
Approximately 0.0
·

Open in Mass Air Flow (MAF) meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and stores a DTC.

Example:

When the sensor output voltage remains at less than 0.2 V, or more than 4.9 V for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P0102: MAF meter range check (Low voltage)
P0103: MAF meter range check (High voltage)
Required Sensors/Components (Main) MAF meter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration 3 seconds
MIL Operation Immediate: Engine speed less than 4000 rpm
2 driving cycles: Engine speed 4000 rpm or more
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None

TYPICAL MALFUNCTION THRESHOLDS

P0102
MAF meter voltage Less than 0.2 V

P0103
MAF meter voltage More than 4.9 V

COMPONENT OPERATING RANGE

MAF meter voltage 0.4 V to 2.2 V

CONFIRMATION DRIVING PATTERN

A228075E01
1.086,1.046 1.714,1.216 0.628,0.170 10 4000 rpm 1.359,1.914 1.717,2.098 0.357,0.184 10 Idling 0.533,2.202 1.709,2.351 1.177,0.149 10 Ignition Switch ON 2.172,2.069 2.369,2.245 0.198,0.177 10 [A] 3.167,1.795 3.364,1.972 0.198,0.177 10 [B] 4,3.098 4.198,3.275 0.198,0.177 10 [C] 6.158,3.098 6.355,3.275 0.198,0.177 10 [E] 4.743,0.71 4.940,0.886 0.198,0.177 10 [D] 2.9,2.818 3.570,2.974 0.670,0.156 10 5 seconds 4.498,0.303 5.167,0.459 0.670,0.156 10 5 seconds

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Run the engine at an engine speed of 4000 rpm or more for 5 seconds [D].

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0102 or P0103.

15.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.



16.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A164719E01
6.245,3.419 6.595,3.584 0.350,0.165 10 ECM 5.812,1.084 6.051,1.249 0.239,0.165 10 VG 4.825,1.084 5.064,1.249 0.239,0.165 10 VG 5.812,1.588 6.126,1.754 0.313,0.165 10 E2G 4.747,1.588 5.061,1.754 0.313,0.165 10 E2G 5.812,2.859 6.237,3.024 0.424,0.165 10 MREL 5.495,2.963 5.789,3.134 0.295,0.171 10 A24 5.495,1.69 5.789,1.873 0.295,0.184 10 D74 5.495,1.185 5.789,1.369 0.295,0.184 10 D74 5.542,1.009 5.726,1.174 0.184,0.165 10 74 5.542,1.503 5.726,1.668 0.184,0.165 10 75 5.542,2.784 5.726,2.949 0.184,0.165 10 34 5.14,1.084 5.268,1.268 0.128,0.184 10 3 5.134,1.601 5.243,1.785 0.110,0.184 10 2 3.729,0.776 3.839,0.959 0.110,0.184 10 1 3.888,0.785 4.109,0.950 0.221,0.165 10 +B 3.813,2.102 4.034,2.286 0.221,0.184 10 D7 3.813,2.261 5.127,2.426 1.313,0.165 10 Mass Air Flow Meter 3.113,0.991 3.778,1.156 0.665,0.165 10 EFI NO. 2 1.123,0.738 1.789,0.904 0.665,0.165 10 EFI NO. 1 2.694,0.869 2.915,1.034 0.221,0.165 10 1B 2.694,1.209 2.915,1.375 0.221,0.165 10 1B 1.559,1.634 1.780,1.800 0.221,0.165 10 1B 0.796,0.864 1.017,1.029 0.221,0.165 10 1C 2.739,0.71 2.849,0.866 0.110,0.156 10 4 2.739,1.047 2.849,1.203 0.110,0.156 10 2 1.376,1.635 1.485,1.791 0.110,0.156 10 3 0.852,0.701 0.962,0.857 0.110,0.156 10 1 2.085,0.491 2.334,0.656 0.248,0.165 10 EFI 1.859,1.843 2.945,2.027 1.086,0.184 10 Integration Relay 0.577,2.803 1.066,2.986 0.489,0.184 10 Battery

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
U151426E01
0.083,0.091 2.434,0.455 2.350,0.364 10 Front view of wire harness connector: (to MAF Meter) 0.999,2.69 1.411,2.828 0.413,0.139 10 +B (+) 1.364,2.033 1.264,2.69 false 0.449,1.915 0.661,2.054 0.211,0.139 10 D7

a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D7-1 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
U151537E02
1.521,1.531 0.833,1.958 false 1.76,1.521 2.448,1.927 false 1.469,3.865 1.75,4.406 false 1.385,3.865 1.031,4.406 false 0.458,1.396 0.729,1.573 0.271,0.177 10 false D7 0.49,1.875 0.833,2.052 0.344,0.177 10 false E2G 2.5,1.844 2.781,2.083 0.281,0.24 10 false VG 0.125,2.917 0.448,3.094 0.323,0.177 10 false D74 1.667,4.427 2.073,4.625 0.406,0.198 10 false E2G 0.917,4.427 1.135,4.604 0.219,0.177 10 false VG 0.156,0.094 2.49,0.438 2.333,0.344 10 false Front view of wire harness connector: (to MAF Meter) 0.146,2.167 2.479,2.51 2.333,0.344 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VG) - D74-74 (VG) Always Below 1 Ω
D7-2 (E2G) - D74-75 (E2G) Always Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle inspection for mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter, referring to the inspection for mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the Techstream on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
U151427E01
0.083,0.056 2.448,0.435 2.364,0.378 10 Front view of wire harness connector: (to MAF Meter) 1.901,2.66 2.212,2.826 0.311,0.166 10 E2G 1.613,1.999 2.006,2.655 false 0.449,1.881 0.661,2.020 0.211,0.139 10 D7

a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
U151537E02
1.521,1.531 0.833,1.958 false 1.76,1.521 2.448,1.927 false 1.469,3.865 1.75,4.406 false 1.385,3.865 1.031,4.406 false 0.458,1.396 0.729,1.573 0.271,0.177 10 false D7 0.49,1.875 0.833,2.052 0.344,0.177 10 false E2G 2.5,1.844 2.781,2.083 0.281,0.24 10 false VG 0.125,2.917 0.448,3.094 0.323,0.177 10 false D74 1.667,4.427 2.073,4.625 0.406,0.198 10 false E2G 0.917,4.427 1.135,4.604 0.219,0.177 10 false VG 0.156,0.094 2.49,0.438 2.333,0.344 10 false Front view of wire harness connector: (to MAF Meter) 0.146,2.167 2.479,2.51 2.333,0.344 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VG) - D74-74 (VG) Always Below 1 Ω
D7-2 (E2G) - D74-75 (E2G) Always Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-1 (+B) - 1B-4 Always Below 1 Ω
D7-1 (+B) or 1B-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR