Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit  P0552  Power Steering Pressure Sensor / Switch Circuit Low Input  P0553  Power Steering Pressure Sensor / Switch Circuit High Input  


DESCRIPTION

The power steering oil pressure sensor is turned ON when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.

DTC No. DTC Detection Condition Trouble Area
P0550 Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0552 Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0553 Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM



MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.

MONITOR STRATEGY

Related DTCs P0550: Power steering pressure sensor range check (Chattering)
P0552: Power steering pressure sensor range check (Low Resistance)
P0553: Power steering pressure sensor range check (High Resistance)
Required sensors/Components (Main) Power steering oil pressure sensor
Frequency of operation Continuous
Duration 0.5 seconds
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Starter OFF
Time after starter signal ON to OFF 2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

P0550
Power steering oil pressure sensor voltage Less than 0.28 V, or more than 4.9 V

P0552
Power steering oil pressure sensor voltage Less than 0.28 V

P0553
Power steering oil pressure sensor voltage More than 4.9 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 5 seconds [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0550, P0552 or P0553.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.


13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162851E07
5.041,0.56 5.354,0.725 0.313,0.165 10 PSP 5.527,2.965 5.812,3.130 0.286,0.165 10 D74 5.036,1.466 5.442,1.631 0.406,0.165 10 VCV1 1.903,0.56 2.216,0.725 0.313,0.165 10 PSP 1.985,1.47 2.215,1.635 0.230,0.165 10 VC 5.041,2.381 5.262,2.537 0.221,0.156 10 E2 5.527,3.129 5.886,3.303 0.360,0.174 10 ECM 4.783,0.471 4.967,0.627 0.184,0.156 10 72 4.783,1.367 4.967,1.523 0.184,0.156 10 67 4.783,2.292 4.967,2.448 0.184,0.156 10 98 2.318,0.462 2.446,0.618 0.128,0.156 10 2 2.304,1.382 2.414,1.543 0.110,0.161 10 1 2.304,2.288 2.423,2.444 0.119,0.156 10 3 2.002,2.389 2.206,2.537 0.205,0.149 10 E2 0.503,2.949 0.791,3.112 0.288,0.163 10 D46 0.503,3.11 2.798,3.280 2.295,0.170 10 Power Steering Oil Pressure Sensor

CAUTION / NOTICE / HINT

HINT:
·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
A379448E01
0.656,1.427 1.083,1.688 0.427,0.26 4.604,0.802 5.031,1.063 0.427,0.26 1.74,1.594 1.26,1.99 true 1.854,1.792 2.406,2.115 true 1.938,1.542 2.583,1.229 true 4.156,1.698 3.896,2.208 true 4.51,1.698 4.333,2.219 true 4.708,1.771 4.927,2.25 true 0.365,0.094 3.292,0.479 2.927,0.385 10 false Front view of wire harness connector: (to Power Steering Oil Pressure Sensor) 3.688,0.073 5.99,0.438 2.302,0.365 10 false Front view of wire harness connector: (to ECM) 0.74,1.469 1.083,1.667 0.344,0.198 10 false D46 1.042,2.01 1.354,2.208 0.313,0.198 10 false VC 2.469,2.063 2.781,2.26 0.313,0.198 10 false E2 2.646,1.156 3.031,1.354 0.385,0.198 10 false PSP 4.698,0.844 5.042,1.042 0.344,0.198 10 false D74 3.708,2.24 4.177,2.438 0.469,0.198 10 false VCV1 4.208,2.25 4.594,2.448 0.385,0.198 10 false PSP 4.854,2.25 5.167,2.448 0.313,0.198 10 false E2

a.

Disconnect the ECM connector.


b.

Disconnect the power steering oil pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D46-2 (PSP) - D74-72 (PSP) Always Below 1 Ω
D46-1 (VC) - D74-67 (VCV1) Always Below 1 Ω
D46-3 (E2) - D74-98 (E2) Always Below 1 Ω
D46-2 (PSP) or D74-72 (PSP) - Body ground Always 10 kΩ or higher
D46-1 (VC) or D74-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF POWER STEERING OIL PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the power steering oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D46-2 (PSP) - D46-3 (E2) Ignition switch ON 4.5 to 5.5 V




OK

3.REPLACE POWER STEERING OIL PRESSURE SENSOR

NG

3.REPLACE POWER STEERING OIL PRESSURE SENSOR
a.

Replace the power steering oil pressure sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

4.CONFIRM WHETHER DTC OUTPUT RECURS
4.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output



NEXT

END