Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).

The intake camshaft has 3 teeth on its outer circumference. When the camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0340
P0345
No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Jumped tooth of timing chain for intake camshaft

·

ECM


P0342
P0347
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Jumped tooth of timing chain for intake camshaft

·

ECM


P0343
P0348
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for intake camshaft circuit

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Jumped tooth of timing chain for intake camshaft

·

ECM



A217926E02
0.218,1.183 0.448,1.348 0.230,0.165 10 NE 0.145,1.733 0.449,1.885 0.304,0.151 10 VV1 0.149,2.105 0.448,2.251 0.299,0.145 10 VV2 2.85,1.275 3.186,1.424 0.336,0.149 10 GND 2.85,2.195 3.186,2.344 0.336,0.149 10 GND 2.85,1.818 3.186,1.967 0.336,0.149 10 GND 1.1,2.509 2.021,2.650 0.921,0.141 10 20 msec./DIV. 2.685,0.797 3.249,0.953 0.563,0.156 10 5 V/DIV. 0.102,0.078 2.419,0.234 2.318,0.156 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-110 (NE+) - D74-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-92 (VV1+) - D74-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-87 (VV2+) - D74-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the intake camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Related DTCs P0340: VVT sensor (for Bank 1) verify pulse input
P0340: VVT sensor (for Bank 1) range check (chattering)
P0342: VVT position sensor (for Bank 1) range check (low voltage)
P0343: VVT position sensor (for Bank 1) range check (high voltage)
P0345: VVT sensor (for Bank 2) verify pulse input
P0345: VVT sensor (for Bank 2) range check (chattering)
P0347: VVT position sensor (for Bank 2) range check (low voltage)
P0348: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main) VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration 5 seconds: P0340, P0345
4 seconds: Others
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs are not stored None

P0340, P0345 (Verify Pulse Input)
Engine speed 600 rpm or more
Battery voltage 8 V or more
Starter OFF
Ignition switch ON
VVT sensor voltage 0.3 to 4.7 V
VVT sensor range check low voltage fail (P0342, P0347) Not detected
VVT sensor range check high voltage fail (P0343, P0348) Not detected

P0342, P0343, P0347, P0348 (Low Voltage, High Voltage)
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345) Not detected
Battery Voltage 8 V or more

TYPICAL MALFUNCTION THRESHOLDS

P0340, P0345 (Verify pulse input):
VVT sensor signal No signal

P0342, P0347 (Low voltage):
VVT sensor voltage Less than 0.3 V

P0343, P0348 (High voltage):
VVT sensor voltage More than 4.7 V

COMPONENT OPERATING RANGE

VVT sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

A198821E06
0.763,1.233 1.197,1.451 0.434,0.218 10 Idling 0.092,1.617 1.354,1.814 1.262,0.198 10 Ignition Switch ON 1.768,1.487 1.994,1.646 0.226,0.159 10 [A] 3.283,1.078 3.476,1.271 0.193,0.193 10 [B] 2.935,2.29 4.212,2.474 1.276,0.184 10 10 seconds or more 4.823,2.914 5.039,3.107 0.216,0.193 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165014E03
0.593,3.888 0.923,4.065 0.330,0.177 10 D39 0.593,2.391 3.082,2.568 2.489,0.177 10 VVT Sensor (for Intake Side of Bank 1) 0.593,2.236 0.923,2.413 0.330,0.177 10 D37 0.593,4.044 3.083,4.220 2.490,0.177 10 VVT Sensor (for Intake Side of Bank 2) 1.529,1.186 1.750,1.339 0.222,0.152 10 VC 1.848,1.277 1.990,1.454 0.142,0.177 10 3 4.845,1.277 5.081,1.454 0.236,0.177 10 66 4.849,1.659 5.085,1.836 0.236,0.177 10 92 4.849,2.042 5.085,2.219 0.236,0.177 10 91 1.354,1.572 1.753,1.724 0.399,0.152 10 VVL+ 1.848,1.663 1.990,1.839 0.142,0.177 10 1 1.385,1.936 1.749,2.088 0.364,0.152 10 VVL- 5.127,1.186 5.598,1.339 0.471,0.152 10 VCV2 5.127,1.572 5.526,1.724 0.399,0.152 10 VV1+ 5.127,1.938 5.487,2.129 0.360,0.192 10 VV1- 4.849,3.322 5.085,3.498 0.236,0.177 10 87 4.849,3.704 5.085,3.881 0.236,0.177 10 88 5.127,3.234 5.526,3.387 0.399,0.152 10 VV2+ 5.127,3.6 5.487,3.792 0.360,0.192 10 VV2- 1.848,2.027 1.990,2.204 0.142,0.177 10 2 1.529,2.833 1.750,2.985 0.222,0.152 10 VC 1.848,2.924 1.990,3.100 0.142,0.177 10 3 1.354,3.218 1.753,3.370 0.399,0.152 10 VVR+ 1.848,3.309 1.990,3.486 0.142,0.177 10 1 1.385,3.582 1.749,3.735 0.364,0.152 10 VVR- 1.848,3.673 1.990,3.850 0.142,0.177 10 2 5.655,4.236 5.987,4.392 0.332,0.156 10 D74 5.655,4.372 6.022,4.527 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
U151398E01
0.04,0.004 2.372,0.354 2.332,0.350 10 Front view of wire harness connector: (to VVT Sensor) 0.263,1.585 0.548,1.732 0.286,0.147 10 D37 0.263,1.929 0.548,2.075 0.286,0.147 10 D39 0.653,1.577 0.809,1.752 0.156,0.174 10 *1 0.653,1.928 0.809,2.102 0.156,0.174 10 *2 2.508,2.429 2.733,2.585 0.225,0.156 10 VC 0.211,2.594 1.093,2.750 0.883,0.156 10 *1: for Bank 1 0.211,2.979 1.093,3.135 0.883,0.156 10 *2: for Bank 2 1.981,2.217 2.485,2.504 false

a.

Disconnect the D37 or D39 VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Bank 1
Tester Connection Switch condition Specified Condition
D37-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V

Bank 2
Tester Connection Switch condition Specified Condition
D39-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)
a.

Disconnect the D37 or D39 VVT sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D37-1 (VVL+) - D74-92 (VV1+) Always Below 1 Ω
D37-2 (VVL-) - D74-91 (VV1-) Always Below 1 Ω
D39-1 (VVR+) - D74-87 (VV2+) Always Below 1 Ω
D39-2 (VVR-) - D74-88 (VV2-) Always Below 1 Ω
D37-1 (VVL+) or D74-92 (VV1+) - Body ground Always 10 kΩ or higher
D37-2 (VVL-) or D74-91 (VV1-) - Body ground Always 10 kΩ or higher
D39-1 (VVR+) or D74-87 (VV2+) - Body ground Always 10 kΩ or higher
D39-2 (VVR-) or D74-88 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)
a.
BR03795E98
2.163,1.53 2.360,1.731 0.197,0.201 10 *c 0.49,1.765 0.757,1.973 0.267,0.208 10 *a 2.673,1.765 2.940,1.973 0.267,0.208 10 *b 2.833,1.978 3.414,2.144 0.581,0.165

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK INTAKE CAMSHAFT (TEETH)

NG

4.CHECK INTAKE CAMSHAFT (TEETH)
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Refer to the confirmation driving pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0340, P0342, P0343, P0345, P0347 or P0348 B

HINT:

If the engine does not start, replace the ECM.




A

END

B