Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT
RM27M0U _51 Engine / Hybrid System _049106 3UR-FE ENGINE MECHANICAL _0234028 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 15781 2.REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)

Hide 15671 3.REMOVE OIL FILTER BRACKET (w/ Oil Cooler)

Hide 15671 4.REMOVE OIL FILTER BRACKET (w/o Oil Cooler)

Hide 12108 6.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 12185 7.REMOVE OIL FILLER CAP HOUSING

a.
A161903

Remove the 2 bolts, filler cap housing and gasket.


Hide 19100P 8.REMOVE SPARK PLUG

Hide 9.REMOVE VVT SENSOR

a.
A161904

LH:

Remove the 2 bolts and 2 VVT sensors.


b.
A161905

RH:

Remove the 2 bolts and 2 VVT sensors.


Hide 11102A 10.REMOVE CAMSHAFT POSITION SENSOR

a.
A161906

Remove the bolt and camshaft position sensor.


Hide 19312 11.REMOVE CRANK POSITION SENSOR PROTECTOR

A161907

a.

Remove the 2 bolts and sensor protector.


Hide 15100R 12.REMOVE CRANKSHAFT POSITION SENSOR

a.
A161908

Remove the bolt and crankshaft position sensor.


Hide 15330B 13.REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

a.
A161909

LH:

Remove the 2 bolts and 2 oil control valves.


b.
A161910

RH:

Remove the 2 bolts and 2 oil control valves.


Hide 11202 14.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 15678A 16.REMOVE OIL CONTROL VALVE FILTER

A164313E06
2.479,0.885 2.479,1.302 false 2.813,0.104 2.969,0.104 2.969,0.104 3.125,0.885 false 1.688,0.417 2.146,0.417 2.146,0.417 2.792,0.792 false 2.313,1.302 2.708,1.542 0.396,0.24 10 false Filter 1.208,0.344 1.75,0.531 0.542,0.188 10 true Gasket 1,0.052 2.854,0.26 1.854,0.208 10 true Cylinder Head Cover Spacer

a.

LH:

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


b.
A164314E07
0.917,0.781 0.917,1.208 false 0.281,0.781 0.635,0.104 0.635,0.104 0.771,0.104 false 0.583,0.708 0.76,0.406 0.76,0.406 1.854,0.417 true 0.75,1.25 1.125,1.458 0.375,0.208 10 false Filter 1.958,0.313 2.458,0.521 0.5,0.208 10 true Gasket 0.802,0.052 2.656,0.26 1.854,0.208 10 true Cylinder Head Cover Spacer

RH:

Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.


Hide 11193 17.REMOVE SPARK PLUG TUBE GASKET

U151527E02
1.563,0.375 1.729,0.375 1.729,0.375 1.927,1.219 true 2.167,1.292 2.458,1.625 0.292,0.333 10 true Pry 1.167,0.271 1.646,0.719 0.479,0.448 10 true Tape

a.

Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.


b.

Using a screwdriver, pry out the gaskets.

NOTICE:

Be careful not to damage the cylinder head cover.


HINT:
·

Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.

·

Tape the screwdriver tip before use.




Hide 16100 18.REMOVE WATER PUMP ASSEMBLY

Hide 11302 19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 21.REMOVE FRONT CRANKSHAFT OIL SEAL

a.

Place the timing chain cover on wooden blocks.


b.
A163996E03
1.177,2.031 0.802,0.875 true 0.802,0.875 2.219,2.042 true 1.552,1.063 0.802,0.875 true 0.177,0.625 0.75,0.979 0.573,0.354 10 true Wooden Block

Place the oil pump on a wooden block.


c.

Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 22.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.

Temporarily tighten the pulley set bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.


A160654E03
3.5,4.823 4.031,5.063 4.031,5.063 4.031,5.177 false 3.656,4.396 4.052,4.01 4.052,4.01 4.177,4.01 true 0.635,0.313 0.448,0.313 0.448,0.313 0.552,0.896 false 1.5,0.333 1.719,0.333 1.719,0.333 1.667,0.802 false 5.646,0.323 5.49,0.323 5.49,0.323 5.563,0.813 true 6.521,0.333 6.771,0.333 6.771,0.333 6.708,0.948 true 0.542,5.594 0.813,6.135 0.813,6.135 1.354,5.594 false 0.323,4.417 0.219,4.417 0.219,4.417 0.521,5.354 false 0.531,3.385 1.042,4.094 1.042,4.094 1.375,3.479 false 5.823,5.604 6.083,6.177 6.083,6.177 6.552,5.604 false 5.323,4.667 5.073,4.667 5.073,4.667 5.542,5.271 false 6.365,4.438 6.875,4.438 6.875,4.438 6.615,5.365 false 5.479,3.646 6,4.063 6,4.063 6.469,3.438 false 0.604,3.208 0.354,2.385 0.354,2.385 0.458,2.385 false 1.74,3.188 2.042,2.385 2.042,2.385 1.906,2.385 false 5.417,3.229 5.177,2.458 5.177,2.458 5.281,2.458 true 6.563,3.281 6.865,2.479 6.865,2.479 6.729,2.479 true 1.396,5.365 1.74,4.938 1.74,4.938 1.635,4.938 false 1.667,5.26 2.083,4.688 2.083,4.688 1.99,4.688 false 1.813,5.292 1.99,5.5 1.99,5.5 1.99,5.771 false 5.385,5.292 5.281,5.438 5.281,5.438 5.281,5.667 false 5.563,4.906 5.448,4.906 5.448,4.906 5.823,5.375 false 3.656,5.198 4.51,5.365 0.854,0.167 10 false Timing Mark 4.208,3.917 4.521,4.115 0.313,0.198 10 false Key 0.688,0.25 1.521,0.427 0.833,0.177 10 false Timing Mark 5.708,0.25 6.542,0.427 0.833,0.177 10 false Timing Mark 0.198,6.167 1.573,6.375 1.375,0.208 10 false Timing Mark Position 0.521,4.115 1.792,4.375 1.271,0.26 10 true Knock Pin Position 5.396,4.573 6.625,4.823 1.229,0.25 10 false Approximately 45° 5.604,4.813 6.833,5.063 1.229,0.25 10 false Approximately 32° 5.5,6.208 6.875,6.417 1.375,0.208 10 false Timing Mark Position 5.427,4.094 6.677,4.302 1.25,0.208 10 true Knock Pin Position 0.552,2.302 1.927,2.479 1.375,0.177 10 false Timing Mark Position 5.354,2.396 6.729,2.573 1.375,0.177 10 false Timing Mark Position 0.365,4.365 1.594,4.615 1.229,0.25 10 true Approximately 2° 0.51,4.865 1.74,5.115 1.229,0.25 10 false Approximately 16° 0.844,4.625 2.073,4.875 1.229,0.25 10 false Approximately 45° 1.708,5.792 2.198,6.167 0.49,0.375 10 false Toward Ceiling 5.031,5.667 5.521,6.042 0.49,0.375 10 false Toward Ceiling 5.167,4.333 6.396,4.583 1.229,0.25 10 true Approximately 18° 3.094,1.052 4.115,1.427 1.021,0.375 10 false Toward Ceiling


Hide 13540 23.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

A160732E02
1.167,1.219 1.604,0.313 true 2.917,1.219 2.281,0.333 true 1.021,1.344 1.177,1.646 false 2.26,1.656 2.656,1.26 false 1.698,0.229 2.281,0.448 0.583,0.219 10 false Plunger 1.198,1.563 2.094,1.76 0.896,0.198 10 true Stopper Plate

a.

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A160733

Remove the 2 bolts, chain tensioner and gasket.


Hide 13559 24.REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH

A178535

Hide 13561 25.REMOVE NO. 1 CHAIN VIBRATION DAMPER LH

A178536

a.

Remove the 2 bolts and chain vibration damper.


Hide 13506 26.REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH

A160655E03
1.865,2.208 1.958,1.844 1.958,1.844 2.104,1.844 false 1.292,2.927 1.583,2.927 1.583,2.927 2.135,2.396 false 2.156,1.771 2.417,1.938 0.26,0.167 10 false Pin 0.688,2.823 1.25,3 0.563,0.177 10 false Plunger 2.198,0.5 2.625,0.844 0.427,0.344 10 true Push

a.

While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


b.
A160656E03
1.031,0.042 1.375,0.229 0.344,0.188 10 false Turn 2.854,0.333 3.26,0.563 0.406,0.229 10 true Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Be careful not to damage the cylinder head with the wrench.

·

Do not disassemble the camshaft timing gear.




c.
A160657E03
1.896,0.708 2.292,1.01 0.396,0.302 10 true Turn 3.031,0.729 3.354,0.896 0.323,0.167 10 false Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:

Be careful not to damage the cylinder head with the wrench.



d.

Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.


e.

Remove the No. 1 and No. 2 chains from the gears.


Hide 13560A 27.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

A148225

a.

Remove the 2 bolts and chain tensioner.


Hide 13540 28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

A150062E03
1.073,0.729 1.5,0.594 true 2.125,0.615 2.802,0.719 true 1,0.938 2.021,1.646 2.021,1.646 2.677,1 true 1.552,0.51 2.042,0.667 0.49,0.156 9 true Plunger 1.385,1.656 2.177,1.833 0.792,0.177 9 true Stopper Plate

a.

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A150146

Remove the 2 bolts and chain tensioner.


Hide 13559 29.REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH

A178486

Hide 13561 30.REMOVE NO. 1 CHAIN VIBRATION DAMPER RH

A160658

a.

Remove the 2 bolts and vibration damper.


Hide 13506 31.REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH

A160659E03
1.323,2.625 1.385,2.333 1.385,2.333 1.479,2.333 false 1.01,2.74 1.01,2.927 false 1.531,2.25 1.781,2.427 0.25,0.177 10 false Pin 0.729,2.906 1.281,3.104 0.552,0.198 10 false Plunger 2.125,0.719 2.531,1.104 0.406,0.385 10 true Push

a.

While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


b.
A160660E01
2.387,0.03 2.762,0.216 0.375,0.186 10 Turn 1.219,0 1.532,0.170 0.313,0.170 10 Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Be careful not to damage the cylinder head with the wrench.

·

Do not disassemble the camshaft timing gear.




c.
A160661E03
0.344,0.688 0.688,0.875 0.344,0.188 10 false Hold 1.552,0.458 1.917,0.75 0.365,0.292 10 true Turn

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:

Be careful not to damage the cylinder head with the wrench.



d.

Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.


e.

Remove the No. 1 and No. 2 chains from the gears.


Hide 13550 32.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A148224

a.

Remove the 2 bolts and chain tensioner.


Hide 13521A 33.REMOVE CRANKSHAFT TIMING GEAR KEY

A145630

a.

Using a screwdriver, remove the 2 timing gear keys from the crankshaft.


Hide 34.REMOVE CAMSHAFT BEARING CAP LH

A163591E04
0.896,2.583 1.771,2.896 1.771,2.896 2.49,2.552 false 1.406,2.927 2.104,3.104 0.698,0.177 10 false Knock Pin 1.292,2.135 1.5,2.323 0.208,0.188 10 false IN 2.865,2.135 3.083,2.302 0.219,0.167 10 false EX 0.708,2.094 1.073,2.333 0.365,0.24 10 false 45° 2.479,2.063 2.792,2.271 0.313,0.208 10 false 3°

a.

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.


b.
A163592E08
0.417,1.729 0.531,1.917 0.115,0.188 10 false 1 0.438,0.198 0.552,0.385 0.115,0.188 10 true 2 1.021,1.729 1.135,1.917 0.115,0.188 10 false 3 1.063,0.198 1.177,0.385 0.115,0.188 10 true 4 1.604,1.74 1.719,1.927 0.115,0.188 10 false 5 1.625,0.198 1.74,0.385 0.115,0.188 10 true 6 2.167,1.74 2.281,1.927 0.115,0.188 10 false 7 2.167,0.198 2.281,0.385 0.115,0.188 10 true 8 2.865,1.729 2.979,1.917 0.115,0.188 10 true 9 2.854,0.208 3.031,0.396 0.177,0.188 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.
A163593E05
3.313,0.135 3.417,0.292 0.104,0.156 10 false 1 3.292,1.667 3.396,1.823 0.104,0.156 10 false 2 0.094,1.417 0.198,1.573 0.104,0.156 10 false 3 2.75,1.781 2.854,1.938 0.104,0.156 10 false 4 3.292,0.51 3.396,0.667 0.104,0.156 10 false 5 0.479,1.875 0.583,2.031 0.104,0.156 10 false 6 0.469,0 0.573,0.156 0.104,0.156 10 false 7 2.198,1.865 2.302,2.021 0.104,0.156 10 false 8 2.229,0 2.333,0.156 0.104,0.156 10 false 9 1.031,1.875 1.219,2.031 0.188,0.156 10 false 10 1.052,0.01 1.24,0.167 0.188,0.156 10 true 11 1.531,1.865 1.719,2.021 0.188,0.156 10 false 12 1.604,0 1.792,0.156 0.188,0.156 10 false 13 2.823,0.542 3.01,0.698 0.188,0.156 10 true 14 0.406,0.542 0.594,0.698 0.188,0.156 10 true 15 2.167,0.531 2.354,0.688 0.188,0.156 10 true 16 1.042,0.542 1.229,0.698 0.188,0.156 10 true 17 1.5,0.542 1.688,0.698 0.188,0.156 10 true 18

Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 6 bearing caps.

HINT:

Arrange the removed parts in the correct order.



e.

Remove the No. 3 and No. 4 camshafts.

HINT:

Arrange the removed parts in the correct order.



Hide 11104A 35.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A163594

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.


HINT:

Tape the screwdriver tip before use.



Hide 36.REMOVE CAMSHAFT BEARING CAP RH

A160683E04
0.698,2.604 1.552,2.875 1.552,2.875 2.083,2.688 false 0.417,2.073 0.74,2.25 0.323,0.177 10 false 55° 1.833,2.104 2.156,2.281 0.323,0.177 10 false 70° 1.188,2.906 1.865,3.094 0.677,0.188 10 false Knock Pin 2.563,2.115 2.76,2.271 0.198,0.156 10 false IN 1,2.104 1.271,2.302 0.271,0.198 10 false EX

a.

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.


b.
A160684E10
0.365,0.188 0.479,0.344 0.115,0.156 10 false 1 0.365,1.646 0.479,1.802 0.115,0.156 10 true 2 0.958,0.208 1.073,0.365 0.115,0.156 10 true 3 1,1.625 1.115,1.781 0.115,0.156 10 true 4 1.542,0.208 1.656,0.365 0.115,0.156 10 false 5 1.552,1.646 1.667,1.802 0.115,0.156 10 true 6 2.115,0.229 2.229,0.385 0.115,0.156 10 true 7 2.125,1.656 2.24,1.813 0.115,0.156 10 true 8 2.802,0.198 2.917,0.354 0.115,0.156 10 true 9 2.771,1.646 2.958,1.802 0.188,0.156 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.
A160685E06
3.24,1.76 3.333,1.917 0.094,0.156 10 false 1 3.208,0.073 3.302,0.229 0.094,0.156 10 false 2 0.146,0.5 0.24,0.656 0.094,0.156 10 true 3 2.604,0.125 2.698,0.281 0.094,0.156 10 false 4 3.156,1.531 3.25,1.688 0.094,0.156 10 false 5 0.302,0.063 0.396,0.219 0.094,0.156 10 false 6 0.302,1.948 0.396,2.104 0.094,0.156 10 false 7 2.021,0.063 2.115,0.219 0.094,0.156 10 false 8 2.063,1.938 2.156,2.094 0.094,0.156 10 false 9 0.875,0.052 1.063,0.208 0.188,0.156 10 false 10 0.896,1.938 1.083,2.094 0.188,0.156 10 false 11 1.375,0.073 1.563,0.229 0.188,0.156 10 false 12 1.448,1.938 1.635,2.094 0.188,0.156 10 false 13 2.646,1.375 2.833,1.531 0.188,0.156 10 true 14 0.25,1.365 0.438,1.521 0.188,0.156 10 true 15 0.885,1.375 1.073,1.531 0.188,0.156 10 true 17 1.5,1.375 1.688,1.531 0.188,0.156 10 true 18 1.99,1.365 2.177,1.521 0.188,0.156 10 true 16

Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 6 bearing caps.

HINT:

Arrange the removed parts in the correct order.



e.

Remove the No. 1 and No. 2 camshafts.

HINT:

Arrange the removed parts in the correct order.



Hide 11103C 37.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

A160735

a.

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.


HINT:

Tape the screwdriver tip before use.



Hide 13801 38.REMOVE VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 32 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 39.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 32 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 40.REMOVE VALVE STEM CAP

a.

Remove the 32 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11116 43.REMOVE CYLINDER HEAD GASKET LH

Hide 11115 44.REMOVE CYLINDER HEAD GASKET RH

Hide 11445 45.REMOVE CYLINDER BLOCK WATER JACKET SPACER

A161997

a.

Remove the 2 water jacket spacers from the cylinder head.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



Hide 12209E 46.REMOVE OIL RETURN PIPE GASKET

a.
A161914

Using a screwdriver, pry out the oil return pipe gasket.

HINT:

Tape the screwdriver tip before use.



Hide 12203A 47.REMOVE VENTILATION PIPE GASKET

a.
A161915

Using a screwdriver, pry out the ventilation pipe gasket.

HINT:

Tape the screwdriver tip before use.



Hide 16877 48.REMOVE NO. 1 HEAT EXCHANGER COVER

a.
A161916E04
2.448,1.771 2.75,2.177 0.302,0.406 9 true Nut 0.646,1.896 0.948,2.167 0.302,0.271 9 true Nut

Remove the 12 bolts and 2 nuts.


b.
A164347

Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.



Hide 12102A 49.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A160720E03
2.885,0.531 3.156,0.708 0.271,0.177 10 false Nut 1.448,1.698 1.719,1.875 0.271,0.177 10 true Nut

Remove the 14 bolts and 2 nuts.


b.
A120816

Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 12101 50.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

a.
A160721E05
2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.813 1.438,1.125 0.292,0.313 10 true Nut

Remove the 14 bolts and 2 nuts.

HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



b.
A160722E01
0.053,0 0.702,0.183 0.649,0.183 10 LH Side: 0.053,1.544 0.688,1.727 0.635,0.183 10 RH Side:

Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.


HINT:

Tape the screwdriver tip before use.



Hide 12121 51.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A160723

Remove the 7 bolts and baffle plate.


Hide 15104 52.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A160724

Remove the 2 bolts, oil strainer and O-ring.


Hide 11381 53.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A145612

Remove the 6 bolts and oil seal retainer.


b.
A380017

Using a screwdriver, pry out the oil seal retainer.

HINT:

Tape the screwdriver tip before use.



Hide 12109A 54.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY

a.
A160728

Remove the bolt and oil drain pipe.


b.

Remove the O-ring.


Hide 11381A 55.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A145614E01
2.581,0.779 3.154,1.116 0.573,0.336 10 Wooden Block 2.249,1.066 2.53,0.945 false

Place the oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the oil seal.


Hide 56.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 57.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.