Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P1340  Camshaft Position Sensor "A" (Bank 1 Sensor 2)  P1342  Camshaft Position Sensor "A" Low Input (MRE)  P1343  Camshaft Position Sensor "A" High Input (MRE)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magnetic Resistance Element).

The camshaft drive gear (LH) has 3 teeth on its inner circumference. When the camshaft gear rotates, air gap changes between the protrusion on the teeth and MRE. The change affects the magnetic field and results in changes in the resistance of the MRE.

The crankshaft position sensor plate has 34 teeth and is installed to the rear end of the crankshaft. The crankshaft position sensor generates 34 signals at every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

DTC Code DTC Detection Condition Trouble Area
P1340 No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing plate LH

·

ECM


No camshaft position sensor signal to ECM with engine speed 600 rpm or more
P1342 Output voltage of camshaft position sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
P1343 Output voltage of camshaft position sensor more than 4.7 V for 4 seconds
(1 trip detection logic)

MONITOR DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE.

The camshaft drive gear has 3 teeth on its inner circumference. When the camshaft gear rotates, air gap changes between the protrusion on the teeth and the MRE. The change affects the magnetic field and results in changes in the resistance of the MRE. The crankshaft position sensor plate has 34 teeth and outputs 34 signals at every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

MONITOR STRATEGY

Related DTCs P1340: Camshaft position sensor verify pulse input
P1340: Camshaft position / Crankshaft position misalignment
P1342: Camshaft position sensor range check (low voltage)
P1343: Camshaft position sensor range check (high voltage)
Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor, Engine speed sensor
Frequency of Operation Continuous
Duration 4 seconds:
P1340 camshaft position sensor verify pulse input
P1342: Camshaft position sensor range check (low voltage)
P1343: Camshaft position sensor range check (high voltage)
5 seconds:
P1340 camshaft position / crankshaft position misalignment
MIL Operation 2 driving cycles: P1340 camshaft position sensor verify pulse input
Immediate: P1340 camshaft position / crankshaft position misalignment and P1342, P1343 camshaft position sensor range check
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P1340 camshaft position sensor verify pulse input:
Monitor runs whenever following DTCs not present None
Starter ON (Not starter ON again)
Minimal battery voltage while starter ON Less than 11 V

P1340 camshaft position / crankshaft position misalignment:
Monitor runs whenever following DTCs not present P0342, P0343 (VVT sensor)
P1342, P1343 (Camshaft position sensor)
Engine RPM 600 rpm or more
Starter OFF
Camshaft position sensor range check fail (P1342, P1343) Not detected
Camshaft position sensor range 0.3 to 4.7 V

P1342, P1343 camshaft position sensor range check:
Monitor runs whenever following DTCs not present P0340, P1340 (Camshaft position sensor)
Time after ignition switch off to ON 2 seconds or more
Camshaft position sensor verify pulse input fail (P1340) Not detected
Battery voltage 8 V or more
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P1340 camshaft position sensor verify pulse input:
Camshaft position signal No signal

P1340 camshaft position / crankshaft position misalignment:
Camshaft position and crankshaft position phase Misaligned

P1342 camshaft position sensor range check:
Camshaft position sensor voltage Less than 0.3 V

P1343 camshaft position sensor range check:
Camshaft position sensor voltage Higher than 4.7 V

COMPONENT OPERATING RANGE

Camshaft position sensor signal
·

Camshaft position sensor voltage fluctuates when the camshaft rotates

·

3 signals per revolution of crankshaft



CONFIRMATION DRIVING PATTERN

A198821E06
0.763,1.233 1.197,1.451 0.434,0.218 10 Idling 0.092,1.617 1.354,1.814 1.262,0.198 10 Ignition Switch ON 1.768,1.487 1.994,1.646 0.226,0.159 10 [A] 3.283,1.078 3.476,1.271 0.193,0.193 10 [B] 2.935,2.29 4.212,2.474 1.276,0.184 10 10 seconds or more 4.823,2.914 5.039,3.107 0.216,0.193 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P1340, P1342 or P1343.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165785E01
5.311,0.997 5.710,1.153 0.399,0.156 10 VCV2 5.311,1.543 5.539,1.699 0.229,0.156 10 G2 5.311,2.086 5.600,2.242 0.289,0.156 10 G2- 5.038,0.923 5.229,1.079 0.191,0.156 10 66 5.038,1.46 5.229,1.616 0.191,0.156 10 90 5.038,1.997 5.229,2.153 0.191,0.156 10 89 2.44,0.998 2.670,1.150 0.230,0.151 10 VC 2.44,1.541 2.670,1.692 0.230,0.151 10 G2 2.44,2.078 2.670,2.229 0.230,0.151 10 G- 2.745,0.918 2.887,1.073 0.142,0.155 10 3 2.745,1.455 2.887,1.610 0.142,0.155 10 1 2.745,1.992 2.887,2.147 0.142,0.155 10 2 5.795,2.623 6.090,2.779 0.295,0.156 10 D74 5.795,2.763 6.136,2.919 0.341,0.156 10 ECM 1.329,2.354 1.555,2.510 0.225,0.156 10 D6 1.329,2.494 2.981,2.660 1.651,0.165 10 Camshaft Position Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
U151397E02
1.99,2.188 2.479,2.74 false 0.594,2.104 0.844,2.302 0.25,0.198 10 false D6 0.333,0.167 2.698,0.531 2.365,0.365 10 false Front view of wire harness connector: (to Camshaft Position Sensor) 2.438,2.781 2.781,2.948 0.344,0.167 10 false VC

a.

Disconnect the D6 camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D6-3 (VC) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
a.

Disconnect the D6 camshaft position sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D6-1 (G2) - D74-90 (G2) Always Below 1 Ω
D6-2 (G-) - D74-89 (G2-) Always Below 1 Ω
D6-1 (G2) or D74-90 (G2) - Body ground Always 10 kΩ or higher
D6-2 (G-) or D74-89 (G2-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SENSOR INSTALLATION
BR03795E98
2.163,1.53 2.360,1.731 0.197,0.201 10 *c 0.49,1.765 0.757,1.973 0.267,0.208 10 *a 2.673,1.765 2.940,1.973 0.267,0.208 10 *b 2.833,1.978 3.414,2.144 0.581,0.165

a.

Check the camshaft position sensor installation.

OK:

The camshaft position sensor is installed properly.




OK

4.INSPECT CAMSHAFT TIMING PLATE (SIGNAL PLATE TOOTH)

NG

4.INSPECT CAMSHAFT TIMING PLATE (SIGNAL PLATE TOOTH)
a.

Check the teeth of the signal plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

5.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

6.CONFIRM WHETHER DTC OUTPUT RECURS
6.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P1340, P1342 and/or P1343 are output B

HINT:

If the engine does not start, replace the ECM.




A

END

B