Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1 and EV2 signals) consists of a magnet and MRE (Magnetic Resistance Element).

The exhaust camshaft has 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0365
P0390
No VVT sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic)
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM


P0367
P0392
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM


P0368
P0393
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM



A217927E02
0.21,1.18 0.440,1.345 0.230,0.165 10 NE 0.137,1.731 0.441,1.882 0.304,0.151 10 EV1 0.141,2.093 0.440,2.238 0.299,0.145 10 EV2 2.847,1.272 3.184,1.421 0.336,0.149 10 GND 2.847,2.197 3.184,2.346 0.336,0.149 10 GND 2.847,1.824 3.184,1.973 0.336,0.149 10 GND 1.07,2.506 1.991,2.648 0.921,0.141 10 20 msec./DIV. 2.691,0.783 3.254,0.939 0.563,0.156 10 5 V/DIV. 0.061,0.068 2.369,0.246 2.308,0.178 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
Tester Connection Tool Setting Condition Specified Condition
D74-110 (NE+) - D74-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-69 (EV1+) - D74-68 (EV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
D74-64 (EV2+) - D74-65 (EV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

EV1+ and EV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the exhaust camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Related DTCs P0365: VVT sensor (for Bank 1) verify pulse input
P0365: VVT sensor (for Bank 1) chattering
P0367: VVT position sensor (for Bank 1) range check (low voltage)
P0368: VVT position sensor (for Bank 1) range check (high voltage)
P0390: VVT sensor (for Bank 2) verify pulse input
P0390: VVT sensor (for Bank 2) chattering
P0392: VVT position sensor (for Bank 2) range check (low voltage)
P0393: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main) VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration 5 seconds: P0365, P0390
4 seconds: Others
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All:
Monitor runs whenever following DTCs are not stored None

P0365, P0390 (Verify Pulse Input):
Engine speed 600 rpm or more
Battery voltage 8 V or more
Starter OFF
Ignition switch ON
Exhaust VVT sensor voltage 0.3 to 4.7 V
Exhaust VVT sensor range check low voltage fail (P0367, P0392) Not detected
Exhaust VVT sensor range check high voltage fail (P0368, P0393) Not detected

P0367, P0368, P0392, P0393 (Low Voltage, High Voltage):
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 2 seconds or more
Exhaust VVT sensor verify pulse input fail (P0365, P0390) Not detected
Battery voltage 8 V or more

TYPICAL MALFUNCTION THRESHOLDS

P0365, P0390 (Verify Pulse Input):
Exhaust VVT sensor signal No signal

P0367, P0392 (Low voltage):
Exhaust VVT sensor voltage Less than 0.3 V

P0368, P0393 (High voltage):
Exhaust VVT sensor voltage More than 4.7 V

COMPONENT OPERATING RANGE

VVT sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

A198821E06
0.763,1.233 1.197,1.451 0.434,0.218 10 Idling 0.092,1.617 1.354,1.814 1.262,0.198 10 Ignition Switch ON 1.768,1.487 1.994,1.646 0.226,0.159 10 [A] 3.283,1.078 3.476,1.271 0.193,0.193 10 [B] 2.935,2.29 4.212,2.474 1.276,0.184 10 10 seconds or more 4.823,2.914 5.039,3.107 0.216,0.193 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Idle the engine for 10 seconds [B].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A165014E02
0.593,3.888 0.923,4.065 0.330,0.177 10 D41 0.593,2.391 3.195,2.568 2.601,0.177 10 VVT Sensor for Exhaust Side (for Bank 1) 0.593,2.236 0.923,2.413 0.330,0.177 10 D40 0.593,4.044 3.263,4.220 2.670,0.177 10 VVT Sensor for Exhaust Side (for Bank 2) 1.442,1.186 1.750,1.339 0.308,0.152 10 VC2 1.442,2.847 1.750,2.999 0.308,0.152 10 VC2 1.848,1.277 1.990,1.454 0.142,0.177 10 3 4.845,1.277 5.081,1.454 0.236,0.177 10 66 4.849,1.659 5.085,1.836 0.236,0.177 10 69 4.849,2.042 5.085,2.219 0.236,0.177 10 68 1.428,1.572 1.753,1.724 0.326,0.152 10 EX+ 1.848,1.663 1.990,1.839 0.142,0.177 10 1 1.449,1.936 1.750,2.088 0.301,0.152 10 EX- 1.428,3.232 1.753,3.384 0.326,0.152 10 EX+ 1.449,3.596 1.750,3.749 0.301,0.152 10 EX- 5.127,1.186 5.598,1.339 0.471,0.152 10 VCV2 5.127,1.572 5.526,1.724 0.399,0.152 10 EV1+ 5.127,1.938 5.487,2.129 0.360,0.192 10 EV1- 4.849,3.322 5.085,3.498 0.236,0.177 10 64 4.849,3.704 5.085,3.881 0.236,0.177 10 65 5.127,3.234 5.526,3.387 0.399,0.152 10 EV2+ 5.127,3.6 5.487,3.792 0.360,0.192 10 EV2- 1.848,2.027 1.990,2.204 0.142,0.177 10 2 1.848,2.924 1.990,3.100 0.142,0.177 10 3 1.848,3.309 1.990,3.486 0.142,0.177 10 1 1.848,3.673 1.990,3.850 0.142,0.177 10 2 5.655,4.236 5.987,4.392 0.332,0.156 10 D74 5.655,4.372 6.022,4.527 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U151396E02
1.99,2.156 2.469,2.583 false 0.198,0.094 2.531,0.469 2.333,0.375 10 false Front view of wire harness connector: (to VVT Sensor) 0.271,1.875 0.573,2.073 0.302,0.198 10 false D40 0.271,2.219 0.563,2.396 0.292,0.177 10 false D41 0.177,2.552 1,2.75 0.823,0.198 10 false 1: for Bank 1 0.177,2.906 1,3.104 0.823,0.198 10 false 2: for Bank 2 2.51,2.563 2.833,2.771 0.323,0.208 10 false VC2 0.646,1.792 0.813,1.99 0.167,0.198 10 false *1 0.646,2.135 0.813,2.333 0.167,0.198 10 false *2

Disconnect the D40 or D41 VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Bank 1
Tester Connection Switch condition Specified Condition
D40-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V

Bank 2
Tester Connection Switch condition Specified Condition
D41-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the D40 or D41 VVT sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D40-1 (EX+) - D74-69 (EV1+) Always Below 1 Ω
D40-2 (EX-) - D74-68 (EV1-) Always Below 1 Ω
D41-1 (EX+) - D74-64 (EV2+) Always Below 1 Ω
D41-2 (EX-) - D74-65 (EV2-) Always Below 1 Ω
D40-1 (EX+) or D74-69 (EV1+) - Body ground Always 10 kΩ or higher
D40-2 (EX-) or D74-68 (EV1-) - Body ground Always 10 kΩ or higher
D41-1 (EX+) or D74-64 (EV2+) - Body ground Always 10 kΩ or higher
D41-2 (EX-) or D74-65 (EV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)
a.
A366136E02
0.469,1.667 1.01,1.875 0.542,0.208 10 false Normal 2.427,1.792 3.063,1.99 0.635,0.198 10 false Abnormal 1.542,1.563 2.271,1.771 0.729,0.208 10 false Clearance

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0365, P0367, P0368, P0390, P0392 or P0393 B

HINT:

If the engine does not start, replace the ECM.




A

END

B