Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT
RM27M0U _51 Engine / Hybrid System _049106 3UR-FE ENGINE MECHANICAL _0234028 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE WIRE

A259653

a.

Engine LH Side:

i.

Disconnect the 2 camshaft timing control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the 2 VVT sensor connectors.


iv.

Disconnect the camshaft position sensor connector.


v.

Disconnect the vacuum switching valve connector (for ACIS).


vi.

Disconnect the purge VSV connector.


vii.

Disconnect the engine coolant temperature sensor connector.


viii.

Disconnect the fuel injector connector.


ix.

Remove the bolt and disconnect the 8 clamps.



b.
A259650

Engine RH Side:

i.

Disconnect the 2 camshaft timing control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the 2 VVT sensor connectors.


iv.

Disconnect the fuel injector connector.


v.

Disconnect the throttle sensor connector.


vi.

Disconnect the oil pressure sender gauge connector.


vii.

Disconnect the 9 clamps.



c.
A259651

Engine Rear Side:

i.

Disconnect the 3 connectors.


ii.

Disconnect the 5 clamps.


iii.

Remove the 3 bolts and disconnect the 3 wires.



d.

Remove the engine wire.


Hide 23801P 2.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

A308965

a.

Remove the No. 1 fuel pipe (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 11415A 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A163838E01
0.081,0.108 0.376,0.319 0.295,0.211 10 RH: 0.081,1.779 0.404,1.990 0.323,0.211 10 LH:

a.

Remove the 2 water drain cock plugs from the water drain cocks.


b.

Remove the 2 water drain cocks from the cylinder block.


Hide 12361 4.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A163786

Remove the nut and mounting insulator.


Hide 12362A 5.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.
A163787

Remove the nut and mounting insulator.


Hide 12311 6.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

A160649

a.

Remove the 4 bolts and mounting bracket.


Hide 12315 7.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

A160648

a.

Remove the 4 bolts and mounting bracket.


Hide 23808 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH

Hide 23807 9.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH

Hide 12262 10.DISCONNECT VENTILATION HOSE ASSEMBLY

Hide 44763A 11.REMOVE NO. 1 TUBE

A163943

a.

Remove the 2 bolts and No. 1 tube.


Hide 23902 13.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A256359

Remove the 2 bolts and No. 2 fuel tube.


Hide 23902 14.REMOVE FUEL TUBE SUB-ASSEMBLY

A256360

Hide 16206A 15.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 16261G 16.REMOVE NO. 1 WATER BY-PASS HOSE

Hide 16355 17.REMOVE FRONT WATER BY-PASS JOINT

Hide 16603 21.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16307A 22.REMOVE FAN BRACKET SUB-ASSEMBLY

Hide 16620 23.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 83530 24.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 16206 27.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 82121 31.REMOVE ENGINE WIRE

A306987

a.

Disconnect the 4 knock sensor connectors.


b.

Disconnect the 3 clamps. Then remove the engine wire.


Hide 19500 34.REMOVE IGNITION COIL ASSEMBLY