Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › KNOCK SENSOR
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233917 KNOCK SENSOR A

3UR-FE ENGINE CONTROL  KNOCK SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89615 1.INSTALL KNOCK SENSOR

HINT:

Perform "Inspection After Repairs" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A152496E13
0.948,0.75 1.135,0.958 0.188,0.208 10 true *a 0.948,1.115 1.104,1.323 0.156,0.208 10 true *b 2.542,0.75 2.698,0.958 0.156,0.208 10 false *c 2.792,1.208 2.948,1.417 0.156,0.208 10 true *d 0.167,1.292 0.385,1.479 0.219,0.188 10 true *e 0.083,2.229 0.323,2.427 0.24,0.198 10 false *a 0.625,2.438 0.823,2.625 0.198,0.188 10 false *f 0.083,2.99 0.281,3.167 0.198,0.177 10 false *e 1.438,2.896 1.76,3.052 0.323,0.156 10 false 10° 1.49,3.073 1.813,3.229 0.323,0.156 10 false 2° 2.115,2.896 2.438,3.052 0.323,0.156 10 false 10° 1.896,2.229 2.146,2.427 0.25,0.198 10 false *c 0.375,4.052 0.698,4.208 0.323,0.156 10 false 10° 0.146,3.385 0.396,3.573 0.25,0.188 10 false *b 1.948,3.375 2.208,3.542 0.26,0.167 10 false *d 3.042,4.063 3.333,4.219 0.292,0.156 10 false 10° 1.698,2.99 1.896,3.167 0.198,0.177 10 false *e 3,2.458 3.198,2.646 0.198,0.188 10 false *f 2.167,3.063 2.49,3.219 0.323,0.156 10 false 2° 0.417,4.24 0.74,4.396 0.323,0.156 10 false 2° 1.208,3.635 1.406,3.823 0.198,0.188 10 false *f 2.302,3.625 2.5,3.813 0.198,0.188 10 false *f 0.146,4.313 0.396,4.5 0.25,0.188 10 false *g 1.781,4.292 2.031,4.479 0.25,0.188 10 false *g 3.094,4.229 3.344,4.385 0.25,0.156 10 false 2°

Install the 4 knock sensors with the 4 bolts so that the knock sensors are angled as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*a Bank 2 Sensor 1
*b Bank 1 Sensor 1
*c Bank 2 Sensor 2
*d Bank 1 Sensor 2
*e Front
*f Upper
*g Rear

NOTICE:

The acceptable installation angle of the knock sensor is between 10° upward and 2° downward from the horizontal position.



b.

Connect the 4 knock sensor connectors.


Hide 12215 2.INSTALL SEPARATOR CASE

a.

Install the separator case with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16293 3.CONNECT NO. 10 WATER BY-PASS HOSE

a.
A313315E02
1.396,0.448 1.438,0.198 1.438,0.198 1.51,0.198 false 1.792,1.583 1.573,1.885 1.573,1.885 1.5,1.885 true 1.281,1.792 1.469,1.958 0.188,0.167 10 true *a 1.51,0.094 1.698,0.26 0.188,0.167 10 false *a

Connect the No. 10 water by-pass hose to the separator case, and slide the clamp to secure the hose.

Text in Illustration
*a White Mark

HINT:

Make sure the hose color matches the connection area color.



Hide 16297 4.CONNECT NO. 9 WATER BY-PASS HOSE

a.
A313316E02
1.396,0.448 1.438,0.198 1.438,0.198 1.51,0.198 false 1.813,1.302 1.531,1.688 1.531,1.688 1.469,1.688 true 1.24,1.594 1.469,1.781 0.229,0.188 10 true *a 1.51,0.094 1.698,0.26 0.188,0.167 10 false *a

Connect the No. 9 water by-pass hose to the separator case, and slide the clamp to secure the hose.

Text in Illustration
*a Pink Mark

HINT:

Make sure the hose color matches the connection area color.



Hide 17111 7.INSTALL INTAKE MANIFOLD