Home › Engine / Hybrid System › 3UR-FE EMISSION CONTROL › AIR SWITCHING VALVE
RM27M0U _51 Engine / Hybrid System _049100 3UR-FE EMISSION CONTROL _0233982 AIR SWITCHING VALVE A

3UR-FE EMISSION CONTROL  AIR SWITCHING VALVE  INSTALLATION  


PROCEDURE

Hide 17363Q 1.INSTALL NO. 3 AIR TUBE

a.
U151442E02
2.01,0.271 2.24,0.448 0.229,0.177 10 true *1

Install a new gasket and the No. 3 air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Identification Color

NOTICE:

Make sure the gasket's claws are not caught between the air tube and air switching valve.


HINT:

The identification color on the flange is orange.



Hide 17362 2.INSTALL NO. 2 AIR TUBE

a.
U151441E02
2.094,0.229 2.302,0.417 0.208,0.188 10 true *1

Install a new gasket and the No. 2 air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Identification Color

NOTICE:

Make sure the gasket's claws are not caught between the air tube and air switching valve.


HINT:

The identification color on the flange is blue.



Hide 25710 3.INSTALL AIR SWITCHING VALVE ASSEMBLY

a.

Install the air switching valve assembly with the 3 bolts to the No. 1 heat exchanger cover.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the 2 air switching valve assembly connectors.


c.

Install the bracket to the air switching valve assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Connect the knock sensor connector.


Hide 17361 4.INSTALL AIR TUBE

a.

Connect the 2 No. 1 air hoses to the air tube.


b.

Connect the air tube to the air switching valve assembly, and install the air tube with the 2 bolts to the No. 1 heat exchanger cover.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A158575E08
1,0.219 0.75,0.219 0.75,0.219 0.385,1.01 true 1.375,1.917 2.083,1.667 2.083,1.667 2.688,1.667 true 2.719,1.573 2.927,1.74 0.208,0.167 10 false *1 1.031,0.125 1.281,0.302 0.25,0.177 10 true *2

Connect the air pump connector clamp holder.

Text in Illustration
*1 No. 2 Air Hose
*2 No. 3 Air Hose


d.

Attach the wire harness claw.


e.

Connect the air pump connector.


f.

Connect the No. 2 air hose and No. 3 air hose, and slide the 2 clamps to secure the hoses.


Hide 16279 5.INSTALL NO. 3 WATER BY-PASS PIPE

HINT:

Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.


a.
A307664E02
0.292,0.708 0.406,0.708 0.406,0.708 0.719,0.969 true 0.365,1.302 0.51,1.302 0.51,1.302 0.74,1.042 false 0.156,1.198 0.323,1.385 0.167,0.188 10 true *a 0.083,0.625 0.25,0.802 0.167,0.177 10 true *b

Install the No. 3 water by-pass pipe to the front water by-pass joint with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a Stopper
*b Protrusion

NOTICE:

Align the notch of the stopper with the protrusion of the front water by-pass joint.



Hide 16355 6.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the front water by-pass joint to the cylinder head with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the engine coolant temperature sensor connector.


Hide 16206 7.CONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass pipe sub-assembly with the 3 bolts to the timing chain cover and front water by-pass joint.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16264D 8.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the water by-pass joint, and slide the clamp to secure the hose.


Hide 16261 9.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Install the No. 1 water by-pass hose to the front water by-pass joint and water inlet housing, and slide the clamp to secure the hose.


Hide 16293 10.INSTALL NO. 10 WATER BY-PASS HOSE

a.
A307663E05
2.177,0.094 2.292,0.094 2.292,0.094 2.417,0.458 false 0.865,1.01 1.031,1.01 1.031,1.01 1.542,1.427 false 2.156,0.792 1.51,0.896 1.51,0.896 2.156,0.885 false 2.521,0.792 3.115,0.854 3.115,0.854 2.51,0.875 true 0.646,0.927 0.823,1.125 0.177,0.198 10 true *1 1.969,0.021 2.156,0.219 0.188,0.198 10 false *2 3.125,0.75 3.333,0.948 0.208,0.198 10 false *b 1.292,0.792 1.5,0.979 0.208,0.188 10 false *a

Install the No. 10 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hoses.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose
*a Paint Mark (Pink)
*b Paint Mark (White)

HINT:

Make sure that the color on the hose matches with the color on the separator case.



Hide 16297 11.INSTALL NO. 9 WATER BY-PASS HOSE

a.

Install the No. 9 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hoses.

HINT:

Make sure that the color on the hose matches with the color on the separator case.



Hide 12611 12.INSTALL NO. 1 ENGINE COVER

A158656

NOTICE:

Make sure that the No. 1 engine cover is level with the top surface of the intake port of the cylinder head for 1 and 2.


HINT:
·

Align the No. 1 engine cover cutouts with the air tube.

·

Align the No. 1 engine cover with the air switching valve surface and cylinder head wall.



Hide 77285D 13.CONNECT FUEL TUBE CLAMP

a.

Connect the fuel tube clamp to the bracket.


Hide 11212 14.INSTALL NO. 2 ENGINE COVER

A307709

NOTICE:

Make sure that the No. 2 engine cover is level with the top surface of the intake port if the cylinder head.


HINT:
·

Align the No. 2 engine cover cutout with the air tube.

·

Align the No. 2 engine cover with the front water by-pass joint and cylinder head wall.



Hide 17111 15.INSTALL INTAKE MANIFOLD

Hide 17104 16.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY