Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  ACIS Control Circuit  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A165943E07
1.042,0.344 1.417,0.813 false 2.135,0.521 1.854,1.094 false 5.49,0.25 5.344,0.448 false 0.063,0.26 1.042,0.438 0.979,0.177 10 false Intake Manifold 2.219,0.427 2.667,0.625 0.448,0.198 10 false IACV 2.792,2.438 3.146,2.604 0.354,0.167 10 false ECM 3.552,2.531 5.073,2.698 1.521,0.167 10 false Throttle Position Sensor 2.156,3.104 3.885,3.271 1.729,0.167 10 false Crankshaft Position Sensor 5.573,0.135 5.969,0.302 0.396,0.167 10 false Close 6.021,1.385 6.438,1.563 0.417,0.177 10 false Open 2.865,0.167 4.698,0.354 1.833,0.188 10 false Throttle Valve Position (deg.) 5.813,1.885 7.094,2.083 1.281,0.198 10 false Engine Speed (rpm)

WIRING DIAGRAM

A164741E12
5.99,3.365 6.396,3.552 0.406,0.188 10 false ECM 5.531,0.781 5.927,0.958 0.396,0.177 10 false ACIS 5.531,2.313 5.99,2.479 0.458,0.167 10 false MREL 5.25,0.604 5.438,0.76 0.188,0.156 10 false 62 5.188,0.792 5.5,0.969 0.313,0.177 10 false D74 5.24,2.229 5.438,2.385 0.198,0.156 10 false 34 5.188,2.417 5.49,2.594 0.302,0.177 10 false A24 3.49,1.083 3.802,1.271 0.313,0.188 10 false D62 3.49,1.229 4.448,1.427 0.958,0.198 10 false VSV for ACIS 4.25,0.667 4.354,0.833 0.104,0.167 10 false 2 3.51,0.667 3.615,0.833 0.104,0.167 10 false 1 1.594,0.927 2.313,1.104 0.719,0.177 10 false EFI NO. 2 2.74,2.188 3.396,2.354 0.656,0.167 10 false EFI NO. 1 3.823,2.719 4.135,2.906 0.313,0.188 10 false EFI 2.906,3.188 3.99,3.365 1.083,0.177 10 false Integration Relay 4.542,2.406 4.802,2.583 0.26,0.177 10 false 1B 4.552,2.052 4.792,2.219 0.24,0.167 10 false 1B 4.604,2.229 4.719,2.396 0.115,0.167 10 false 2 4.604,1.875 4.719,2.042 0.115,0.167 10 false 4 2.188,2.417 2.458,2.604 0.271,0.188 10 false 1B 2.24,2.24 2.354,2.406 0.115,0.167 10 false 3 2.198,2.052 2.448,2.219 0.25,0.167 10 false 1C 2.24,1.875 2.344,2.031 0.104,0.156 10 false 1 0.792,2.875 1.26,3.052 0.469,0.177 10 false Battery

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE VSV FOR ACIS)
A067588E26
0.469,1.458 0.323,1.698 false 0.667,1.313 0.906,1.792 false 1.979,1.448 1.833,1.688 false 2.177,1.292 2.5,1.76 false 0.479,0.042 1.438,0.25 0.958,0.208 10 false VSV is ON 1.969,0.042 3.063,0.25 1.094,0.208 10 false VSV is OFF 0.531,0.292 0.917,0.49 0.385,0.198 10 false Air 2.021,0.375 2.354,0.573 0.333,0.198 10 false Air 2.771,0.365 3.375,0.573 0.604,0.208 10 false Air Filter 2.313,1.76 2.844,1.969 0.531,0.208 10 false Port E 1.573,1.708 2.094,1.917 0.521,0.208 10 false Port F 0.688,1.823 1.24,2.021 0.552,0.198 10 false Port E 0.042,1.729 0.542,1.917 0.5,0.188 10 false Port F

a.

Disconnect the vacuum hose from port F on the vacuum switching valve (for ACIS).


b.

Connect the Techstream to the DLC3.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control.


e.

Operate the VSV for ACIS.


f.

Check the VSV air flow when switching the VSV.

OK:
Test Condition Specified Condition
VSV is ON Air from port E flows out through port F
VSV is OFF Air from port E flows out through air filter




OK

2.CHECK VACUUM HOSES (VACUUM SWITCHING VALVE - INTAKE AIR CONTROL VALVE, INTAKE MANIFOLD)

NG

4.INSPECT VACUUM SWITCHING VALVE (FOR ACIS)
2.CHECK VACUUM HOSES (VACUUM SWITCHING VALVE - INTAKE AIR CONTROL VALVE, INTAKE MANIFOLD)

OK

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

NG

REPAIR OR REPLACE VACUUM HOSES

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)
a.

Inspect the intake air control valve (See page Engine / Hybrid System>3UR-FBE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.INSPECT VACUUM SWITCHING VALVE (FOR ACIS)
a.


OK

5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM AND INTEGRATION RELAY)

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACIS)

5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM AND INTEGRATION RELAY)
a.

Remove the EFI NO. 2 fuse from the engine room relay block.


b.

Check the EFI NO. 2 fuse.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse Always Below 1 Ω



d.

Reinstall the EFI NO. 2 fuse.


e.

Disconnect the D62 intake air control valve connector.


f.

Disconnect the D74 ECM connector.


g.

Remove the integration relay from the engine room relay block (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>EFI RELAY>ON-VEHICLE INSPECTION).


h.

Disconnect the 1B integration relay connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D62-2 - D74-62 (ACIS) Always Below 1 Ω
D62-1 - 1B-4 Always Below 1 Ω
D62-2 or D74-62 (ACIS) - Body ground Always 10 kΩ or higher
D62-1 or 1B-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR