The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Disconnect the fuel injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | H1-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | F1-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | H2-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | F2-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 5 | H3-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 6 | F3-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 7 | H4-2 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 8 | F4-2 - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Inspect the fuel injector (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Disconnect the fuel injector connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | H1-1 - Body ground | Always | 10 kΩ or higher |
| H1-1 - D74-86 (#10) | Always | Below 1 Ω | |
| No. 2 | F1-1 - Body ground | Always | 10 kΩ or higher |
| F1-1 - D74-109 (#20) | Always | Below 1 Ω | |
| No. 3 | H2-1 - Body ground | Always | 10 kΩ or higher |
| H2-1 - D74-85 (#30) | Always | Below 1 Ω | |
| No. 4 | F2-1 - Body ground | Always | 10 kΩ or higher |
| F2-1 - D74-108 (#40) | Always | Below 1 Ω | |
| No. 5 | H3-1 - Body ground | Always | 10 kΩ or higher |
| H3-1 - D74-84 (#50) | Always | Below 1 Ω | |
| No. 6 | F3-1 - Body ground | Always | 10 kΩ or higher |
| F3-1 - D74-107 (#60) | Always | Below 1 Ω | |
| No. 7 | H4-1 - Body ground | Always | 10 kΩ or higher |
| H4-1 - D74-83 (#70) | Always | Below 1 Ω | |
| No. 8 | F4-1 - Body ground | Always | 10 kΩ or higher |
| F4-1 - D74-106 (#80) | Always | Below 1 Ω |
OK
NG
Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| INJ fuse | Always | Below 1 Ω |
| IG2 MAIN fuse | Always | Below 1 Ω |
OK
NG
Inspect the integration relay (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>IGNITION RELAY NO. 2>ON-VEHICLE INSPECTION).
OK
NG