Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal sensor assembly and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A308494E07
0.357,0.478 2.532,0.671 2.174,0.193 10 Accelerator Pedal Position Sensor 0.357,1.272 2.457,1.632 2.100,0.360 10 Master Cylinder Pressure Sensor (Brake Actuator Assembly) 0.367,2.496 2.180,2.716 1.813,0.221 10 Stop Light Switch Assembly 0.376,3.28 1.985,3.649 1.610,0.369 10 Vehicle Speed Sensor or Wheel Speed Sensor 2.754,0.693 3.929,1.052 1.174,0.360 10 Actual Accelerator Pedal Angle 2.834,1.711 3.851,2.043 1.017,0.332 10 Master Cylinder Pressure 3.02,2.701 3.667,2.903 0.647,0.202 10 ON/OFF 2.852,3.719 3.832,3.912 0.980,0.193 10 Vehicle Speed 5.69,1.856 7.008,2.414 1.319,0.559 10 Effective Accelerator Pedal Angle for System Control

Activation Conditions:
·

Vehicle is running at or above the specified speed.

·

When the accelerator pedal and brake pedal are depressed.


NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

Driving torque is restricted.


HINT:

When this control is activated, the accelerator opening value is forcibly reduced to a fixed value. Therefore, the Accelerator Position value in the Data List is fixed regardless of the actual accelerator opening value (Accel Sens. No.1 Volt %).



Deactivation Conditions:
·

When the brake pedal or the accelerator pedal returns to some degree.



CAUTION / NOTICE / HINT

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving, make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Accelerator Position in the Data List and Accel Sens. No.1 Volt % values diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No.1 Volt % is changing, check that this control is activated (use the Techstream data saving function to record data while driving the vehicle, and then confirm it after driving is completed).



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: System Select / Health Check.


d.

Check DTCs.

Result
Result Proceed to
No DTC output A
DTC output B



A

2.READ VALUE USING TECHSTREAM (MASTER CYLINDER SENSOR)

B

GO TO DTC CHART

2.READ VALUE USING TECHSTREAM (MASTER CYLINDER SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List / Master Cylinder Sensor.


e.

Read the value displayed on the Techstream.

Tester Display Measurement Item/Range Normal Condition
Master Cylinder Sensor Master cylinder pressure sensor reading/
Min.: 0.00 V, Max.: 5.00 V
·

Brake pedal released: 0.30 to 0.90 V

·

Reading increases when brake pedal is depressed




f.

Check that the brake fluid pressure value of the "Master Cylinder Sensor" observed on the Techstream changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the Techstream increases.




OK

3.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH AND ST1)

NG

INSPECT BRAKE ACTUATOR ASSEMBLY

3.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH AND ST1)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.


d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
Techstream Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON




OK

4.INSPECT BRAKE PEDAL

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

4.INSPECT BRAKE PEDAL
a.

Inspect and adjust the brake pedal (See page Brake>BRAKE>BRAKE PEDAL>ADJUSTMENT).

HINT:

If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.




OK

5.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL

5.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.


d.

Read the value displayed on the Techstream.

OK:
Techstream Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator Pedal
Released → Depressed → Released
Values smoothly change following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).




OK

6.READ VALUE USING TECHSTREAM (VEHICLE SPEED)

NG

6.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Read the value displayed on the Techstream.

Standard:
Techstream Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.




OK

7.READ VALUE USING TECHSTREAM (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO VEHICLE SPEED SENSOR "A"

7.READ VALUE USING TECHSTREAM (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


e.

Read the value displayed on the Techstream.

Standard:
Techstream Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.




OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR