77641A
1.INSTALL NO. 1 FUEL TANK PROTECTOR (w/ Cover)
Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.
Attach the 4 clamps to install a new No. 1 fuel tank protector.
77020A
2.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
77213B
3.INSTALL FUEL TANK TO FILLER PIPE HOSE
Install the fuel tank to filler pipe hose to the fuel tank assembly.
77697A
4.INSTALL NO. 2 FUEL TANK HEAT INSULATOR (for 144 L (38 US gal) Fuel Tank)
Install the No. 2 fuel tank heat insulator with the 3 clips.
77697
5.INSTALL NO. 1 FUEL TANK HEAT INSULATOR
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank heat insulator with the 4 clips and nut.
for 144 L (38 US gal) Fuel Tank:
Install the No. 1 fuel tank heat insulator with the 2 clips and 2 nuts.
6.INSTALL FUEL PRESSURE SWITCHING VALVE ASSEMBLY
Install the fuel pressure switching valve assembly with the 2 tube joint clips.
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the tube joint clips are on the collars of the fuel tube joints.
After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.
77204A
7.INSTALL FUEL TANK RETURN TUBE
Install the fuel tank return tube with the tube joint clip.
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the tube joint clips are on the collars of the fuel tube joints.
After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.
77201
8.INSTALL INLET FUEL TANK PIPE SUB-ASSEMBLY
Install the inlet fuel tank pipe sub-assembly with the 2 nuts.
77100
9.INSTALL FUEL TANK ASSEMBLY
Set the fuel tank assembly on an engine lifter and raise the fuel tank assembly.
Connect the wire harness clamp, fuel pump connector and fuel pressure switching valve connector to the fuel tank assembly.
Be careful not to cut the wiring.
w/ Cover:
Attach the 3 claws to install the No. 2 fuel tank protector.
Raise the engine lifter.
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 pins and 2 clips.
Connect the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 bolts.
for 144 L (38 US gal) Fuel Tank:
Install the 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly with the 3 pins and 3 clips.
Connect the 2 No. 1 fuel tank band sub-assemblies and No. 2 fuel tank band sub-assembly with the 3 bolts.
77754
10.CONNECT OUTLET NO. 1 CANISTER HOSE
Connect the outlet No. 1 canister hose to the inlet fuel tank pipe sub-assembly.
Attach the hose to the No. 1 breather tube clamp.
77213B
11.CONNECT FUEL TANK TO FILLER PIPE HOSE
Connect the fuel tank to filler pipe hose to the inlet fuel tank pipe sub-assembly.
Connect the fuel tank breather tube to the inlet fuel tank pipe sub-assembly.
Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
Attach the fuel tank to filler pipe hose and fuel tank breather tube to the No. 1 breather tube clamp.
12.CONNECT WIRE HARNESS
Attach the harness clamp to the fuel tank assembly.
13.CONNECT VENT LINE HOSE
Connect the vent line hose and push down on the retainer.
Before connecting the hose, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.
After connecting, check if the hose and the connector are securely connected by pulling on them.
77204A
14.CONNECT FUEL TANK RETURN TUBE
for 100 L (26.4 US gal) Fuel Tank:
Connect the fuel tank main tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
for 144 L (38 US gal) Fuel Tank:
Connect the fuel tank main tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Push down the retainer.
77209D
15.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
for 100 L (26.4 US gal) Fuel Tank:
Connect the fuel tank return tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.
for 144 L (38 US gal) Fuel Tank:
Connect the fuel tank return tube.
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Push the parts together firmly until a "click" sound is heard.
Push down the retainer.
77606
16.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
for 100 L (26.4 US gal) Fuel Tank:
Install the No. 1 fuel tank protector sub-assembly with the 2 bolts and 2 nuts.
for 144 L (38 US gal) Fuel Tank:
Install the No. 1 fuel tank protector sub-assembly with the 6 nuts.
Connect the fuel pressure switching valve with the bolt.
77310A
17.INSTALL FUEL TANK CAP
28800
18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
19.INSPECT FOR FUEL LEAK