19500
1.INSTALL IGNITION COIL ASSEMBLY
89615
2.INSTALL KNOCK SENSOR
12215
3.INSTALL SEPARATOR CASE
82121
4.INSTALL ENGINE WIRE
Connect the 3 clamps and 4 knock sensor connectors.
17363Q
5.INSTALL NO. 3 AIR TUBE
17362
6.INSTALL NO. 2 AIR TUBE
25710
7.INSTALL AIR SWITCHING VALVE ASSEMBLY
16206
8.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
16323
9.INSTALL WATER INLET HOUSING
17361
10.INSTALL AIR TUBE
83530
11.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
16603
12.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16173
13.INSTALL WATER PUMP PULLEY
12611
14.INSTALL NO. 1 ENGINE COVER
11212
15.INSTALL NO. 2 ENGINE COVER
16355
16.INSTALL FRONT WATER BY-PASS JOINT
16261G
17.INSTALL NO. 1 WATER BY-PASS HOSE
16206A
18.INSTALL NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)
23901
19.INSTALL FUEL TUBE SUB-ASSEMBLY
23902
20.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY
Install the No. 2 fuel tube with the 2 bolts.
17111
21.INSTALL INTAKE MANIFOLD
44763A
22.INSTALL NO. 1 TUBE
Install the No. 1 tube with the 2 bolts.
12262
23.CONNECT VENTILATION HOSE ASSEMBLY
23807
24.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
23808
25.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
12315
26.INSTALL NO. 1 ENGINE MOUNTING BRACKET LH
Install the mounting bracket with the 4 bolts.
12311
27.INSTALL NO. 1 ENGINE MOUNTING BRACKET RH
Install the mounting bracket with the 4 bolts.
12361
28.INSTALL FRONT ENGINE MOUNTING INSULATOR RH
Install the mounting insulator with the nut.
11415A
29.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the drain cocks.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the water drain cocks.
Further tighten the drain cocks within 360° so that the drain cock pipes are within the range shown in the illustration.
Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.
Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.
Install the water drain cock plugs to the water drain cocks.
12362A
30.INSTALL FRONT ENGINE MOUNTING INSULATOR LH
Install the mounting insulator with the nut.
23801P
31.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
Install the No. 1 fuel pipe (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>PRECAUTION).
32.INSTALL ENGINE WIRE
Install the engine wire.
Engine Rear Side:
Install the 3 wires with the 3 bolts.
Connect the 5 clamps.
Connect the 3 connectors.
Engine RH Side:
Connect the 9 clamps.
Connect the oil pressure sender gauge connector.
Connect the throttle sensor connector.
Connect the fuel injector connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connectors.
Engine LH Side:
Connect the 8 clamps and install the engine wire with the bolt.
Connect the fuel injector connector.
Connect the engine coolant temperature sensor connector.
Connect the purge VSV connector.
Connect the vacuum switching valve connector (for ACIS).
Connect the camshaft position sensor connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connector.