Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CAMSHAFT(for Bank 1) › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234034 CAMSHAFT(for Bank 1) A

1UR-FE ENGINE MECHANICAL  CAMSHAFT(for Bank 1)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform " Inspection After Repairs" after replacing the No. 3 or No. 4 camshaft or camshaft timing gear LH or camshaft timing exhaust gear LH (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING CAP LH

HINT:

Perform "Inspection After Repairs" after replacing the No. 3 or No. 4 camshaft (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A217487E03
2.292,0.156 2.479,0.344 0.188,0.188 9 false L2 1.813,0.167 1.979,0.365 0.167,0.198 9 false L3 1.344,0.167 1.521,0.354 0.177,0.188 9 false L4 0.813,0.167 0.979,0.344 0.167,0.177 9 false L5 1.365,1.906 1.531,2.094 0.167,0.188 9 false L3

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.

Install the No. 3 and No. 4 camshafts to the camshaft housing.


c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
U151680E02
2.708,0.24 2.813,0.385 0.104,0.146 10 true 1 2.719,1.729 2.823,1.875 0.104,0.146 10 true 2 2.094,0.219 2.198,0.365 0.104,0.146 10 true 3 2.094,1.729 2.198,1.875 0.104,0.146 10 false 4 1.615,0.229 1.719,0.375 0.104,0.146 10 false 5 1.625,1.729 1.729,1.875 0.104,0.146 10 false 6 1.135,0.229 1.24,0.375 0.104,0.146 10 true 7 1.125,1.719 1.229,1.865 0.104,0.146 10 false 8 0.552,0.229 0.667,0.375 0.115,0.146 10 false 9 0.51,1.729 0.698,1.885 0.188,0.156 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11104A 2.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
U151458E02
1.479,0.625 1.76,0.76 1.76,0.76 1.885,0.76 false 1.281,1.646 1.698,1.646 false 1.906,0.125 3.115,0.333 1.208,0.208 10 false Valve Rocker Arm 1.938,0.698 2.979,0.938 1.042,0.24 10 false Valve Stem Cap 1.75,1.552 3.021,1.74 1.271,0.188 10 false Valve Lash Adjuster

Install the valve rocker arms as shown in the illustration.


b.
A380006E01
0.781,1.688 2.594,1.906 1.813,0.219 10 false Seal diameter: 3.5 to 4.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163732E06
0.917,2.583 1.813,2.938 1.813,2.938 2.51,2.573 false 1.51,0.552 1.615,0.708 0.104,0.156 10 true 1 1.042,0.552 1.146,0.708 0.104,0.156 10 true 2 2.156,0.552 2.26,0.708 0.104,0.156 10 true 3 0.406,0.563 0.51,0.719 0.104,0.156 10 true 4 2.802,0.552 2.948,0.719 0.146,0.167 10 true 5 1.604,0 1.708,0.156 0.104,0.156 10 false 6 1.521,1.885 1.625,2.042 0.104,0.156 10 false 7 1.042,0 1.146,0.156 0.104,0.156 10 false 8 1.031,1.885 1.135,2.042 0.104,0.156 10 false 9 2.135,0 2.323,0.156 0.188,0.156 10 false 10 2.083,1.885 2.271,2.042 0.188,0.156 10 false 11 0.354,0 0.542,0.156 0.188,0.156 10 false 12 0.365,1.885 0.552,2.042 0.188,0.156 10 false 13 3.208,0.531 3.396,0.688 0.188,0.156 10 false 14 2.646,1.844 2.833,2 0.188,0.156 10 false 15 0.052,1.406 0.24,1.563 0.188,0.156 10 false 16 2.979,1.438 3.167,1.594 0.188,0.156 10 false 17 1.302,2.094 1.49,2.271 0.188,0.177 10 false IN 2.875,2.125 3.146,2.26 0.271,0.135 10 false EX 1.448,2.927 2.125,3.094 0.677,0.167 10 false Knock Pin 2.5,2.073 2.781,2.25 0.281,0.177 10 false 3° 0.698,2.083 1.01,2.292 0.313,0.208 10 false 45° 3.208,0.021 3.396,0.177 0.188,0.156 10 false 18 2.885,0.021 3.021,0.188 0.135,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A163592E07
2.885,0.208 3,0.396 0.115,0.188 10 true 1 2.875,1.729 2.99,1.917 0.115,0.188 10 true 2 2.188,0.198 2.302,0.385 0.115,0.188 10 true 3 2.156,1.729 2.271,1.917 0.115,0.188 10 false 4 1.625,0.198 1.74,0.385 0.115,0.188 10 true 5 1.604,1.729 1.719,1.917 0.115,0.188 10 false 6 1.073,0.208 1.188,0.396 0.115,0.188 10 true 7 1.021,1.729 1.135,1.917 0.115,0.188 10 false 8 0.438,0.219 0.552,0.406 0.115,0.188 10 true 9 0.385,1.729 0.563,1.917 0.177,0.188 10 false 10

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13560A 3.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

U151670E02
2.167,1.781 2,1.781 2,1.781 1.813,2.167 false 1.271,2.813 1.479,2.813 1.479,2.813 2.115,2.313 false 2.563,0.292 2.938,0.438 0.375,0.146 10 false Push 2.208,1.677 2.448,1.844 0.24,0.167 10 false Pin 0.635,2.708 1.167,2.875 0.531,0.167 10 false Plunger

a.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

While pushing down the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 4.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear LH or camshaft timing exhaust gear LH (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A160665E05
1.01,0.75 1.115,1.156 1.115,1.156 1.292,1.156 true 1.115,0.656 1.115,0.146 true 0.875,0.708 0.875,0.146 0.875,0.146 1.396,0.146 true 1.438,0.063 2.708,0.24 1.271,0.177 10 false Orange Mark Plate 1.323,1.063 2.146,1.271 0.823,0.208 10 true Timing Mark

Align the No. 1 chain's orange mark plates with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


b.
A149462E10
2.385,1.281 1.792,1.688 true 1.688,1.49 1.146,1.438 true 0.375,1.344 1.167,1.521 0.792,0.177 10 false Timing Mark 2.448,1.208 3.167,1.531 0.719,0.323 10 false Orange Mark Plate

Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


c.
A160666E07
0.813,0.792 1,0.125 1,0.125 1.115,0.125 true 2.146,0.115 2.25,0.115 2.25,0.115 2.469,0.667 true 0.781,1.094 1.583,1.896 1.583,1.896 2.469,0.99 true 1.25,0.031 2.083,0.24 0.833,0.208 10 false Timing Mark 0.875,1.906 2.021,2.083 1.146,0.177 10 true Yellow Mark Plate

Align the No. 2 chain's yellow mark plates with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

HINT:

The crankshaft timing gear and camshaft exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket to the crankshaft.


e.

Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear.

NOTICE:

Because the gears' timing mark positions may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.



g.

Remove the pin from the No. 2 chain tensioner.


Hide 13559 5.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH

A214800

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain and install the chain tensioner.


Hide 13540 6.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

A148260E01
2.712,1.388 3.255,1.572 0.543,0.184 10 Plunger 0.1,0.606 0.973,0.794 0.873,0.188 10 Stopper Plate 2.425,1.1 2.682,1.467 2.682,1.467 1.951,1.72 false 1.996,0.979 1.174,0.693 1.174,0.693 1.361,1.403 false

a.

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A214606

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13561 7.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

A214801

a.

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Remove the hexagon wrench from the No. 1 chain tensioner.


Hide 13050 8.TIGHTEN CAMSHAFT TIMING GEAR LH

a.
A214802E04
2.885,0.365 3.208,0.542 0.323,0.177 10 true Hold 0.74,0.115 1.083,0.302 0.344,0.188 10 false Turn

Using a wrench to hold the hexagonal portion of the No. 3 camshaft, tighten the camshaft timing gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


b.
A214803E04
0.875,0.208 1.208,0.417 0.333,0.208 10 true Turn 3,0.75 3.323,0.896 0.323,0.146 10 false Hold

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the camshaft timing exhaust gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 11302 10.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Install the timing chain cover (See page Engine / Hybrid System>1UR-FE LUBRICATION>OIL PUMP>INSTALLATION).