Home › Engine / Hybrid System › 1UR-FE LUBRICATION › OIL PUMP
RM27M0U _51 Engine / Hybrid System _049115 1UR-FE LUBRICATION _0234076 OIL PUMP A

1UR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 16322 1.INSTALL WATER INLET PIPE

a.

Apply soapy water to 2 new O-rings and install them to the water inlet pipe.


b.

Install the water inlet pipe to the No. 1 heat exchanger cover.


Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new oil pump gasket.


b.

Install the oil pump gasket to the cylinder block.


c.

Apply a light coat of engine oil to a new O-ring.


d.

Install the O-ring to the oil pan sub-assembly.


e.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A380068E01
1.323,2 1.438,2.094 1.438,2.094 1.583,2.094 true 4.354,1.906 4.219,1.979 4.219,1.979 4.042,1.979 true 2.5,0.625 2.635,0.792 0.135,0.167 10 false A 2.823,0.625 2.958,0.792 0.135,0.167 10 false A 1.01,1.333 1.146,1.5 0.135,0.167 10 true C 1.625,2.021 1.99,2.198 0.365,0.177 10 true B - B 0.74,2.417 0.875,2.583 0.135,0.167 10 false B 0.948,3.073 1.083,3.24 0.135,0.167 10 false C 3.073,1.896 3.208,2.063 0.135,0.167 10 true C 2.125,1.813 2.26,1.979 0.135,0.167 10 true D 4.792,2.313 4.927,2.479 0.135,0.167 10 false B 3.635,1.896 4,2.073 0.365,0.177 10 true A - A 4.052,3.052 4.188,3.219 0.135,0.167 10 false C 0.75,3.854 0.854,4.021 0.104,0.167 10 false : 0.75,4.135 0.854,4.302 0.104,0.167 10 false : 0.75,4.448 0.854,4.615 0.104,0.167 10 false : 0.854,3.875 1.021,4.042 0.167,0.167 10 false *a 0.854,4.156 1.021,4.323 0.167,0.167 10 false *b 0.865,4.448 1.031,4.615 0.167,0.167 10 false *c 6.313,4.344 6.677,4.521 0.365,0.177 10 true B - B 4.802,4.354 5.167,4.531 0.365,0.177 10 true A - A 4.135,3.448 4.615,3.625 0.479,0.177 10 true 7.0 mm 5.781,3.417 6.26,3.594 0.479,0.177 10 true 7.0 mm 5.552,0.385 6.927,0.573 1.375,0.188 10 false A: 20.0 mm (0.787 in.) 5.552,0.688 6.927,0.875 1.375,0.188 10 false B: 26.0 mm (1.02 in.) 5.552,0.99 6.927,1.177 1.375,0.188 10 false C: 16.0 mm (0.630 in.) 5.563,1.281 6.938,1.469 1.375,0.188 10 false D: 18.0 mm (0.709 in.)

Text in Illustration
*a Continuous Line Area *b Dashed Line Area
*c Diagonal Line Area - -

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A150825E11
1.771,1.219 2.406,0.833 2.406,0.833 2.667,0.833 true 2.708,1.74 2.927,1.906 0.219,0.167 10 false *b 2.75,0.75 3.302,0.917 0.552,0.167 10 false *c 0.156,1.646 0.875,1.813 0.719,0.167 10 false 2.0 (0.079) 0.167,1.323 0.875,1.49 0.708,0.167 10 false 3.2 (0.126) 0.167,0.604 0.875,0.771 0.708,0.167 10 false 6.0 (0.236) 1.052,1.75 1.281,1.917 0.229,0.167 10 false 8.0 0.167,1.135 0.896,1.302 0.729,0.167 10 false 4.0 (0.157) 2.115,1.75 2.417,1.906 0.302,0.156 10 false 12.0 1.604,1.75 1.917,1.927 0.313,0.177 10 false 10.0 1.615,2.917 1.813,3.083 0.198,0.167 10 false *b 0.927,2.521 1.135,2.688 0.208,0.167 10 false *a 0.958,1.948 1.438,2.125 0.479,0.177 10 false (0.315) 1.542,1.958 2.021,2.146 0.479,0.188 10 false (0.394) 2.083,1.958 2.573,2.135 0.49,0.177 10 false (0.472) 0.74,0.313 0.938,0.5 0.198,0.188 10 false *a

Apply Seal Packing As Follows:
Area Seal Packing Diameter Application Position from Inside Edge of Cover
Continuous Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 2.5 mm (0.0984 in.)
Dashed Line Area 6.4 mm (0.252 in.) or more, or within OK area shown in illustration 7.0 mm (0.276 in.)
Diagonal Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 5.5 mm (0.217 in.)



Text in Illustration
*a Seal Packing Thickness
*b Seal Packing Width
*c OK Area

NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing.




f.
A210031

Align the oil pump drive rotor spline and crankshaft as shown in the illustration and install the timing chain cover sub-assembly.


g.
U151643E02
2.698,0.823 2.844,1 0.146,0.177 10 false B 1.802,0.469 1.969,0.625 0.167,0.156 10 false *1 2.208,0.188 2.354,0.365 0.146,0.177 10 false A 1.781,2.021 1.938,2.229 0.156,0.208 10 true E 2.833,1.948 2.979,2.125 0.146,0.177 10 false D 1.26,1.708 1.406,1.885 0.146,0.177 10 false C 2.563,2.708 2.708,2.885 0.146,0.177 10 false A 2.208,3.01 2.354,3.188 0.146,0.177 10 false A 1.792,3.063 1.938,3.24 0.146,0.177 10 false A 1.458,3.063 1.604,3.24 0.146,0.177 10 false A 1.052,3 1.198,3.177 0.146,0.177 10 false A 0.198,1.865 0.344,2.042 0.146,0.177 10 false A 0.229,1 0.375,1.177 0.146,0.177 10 false A 1.365,0.375 1.51,0.552 0.146,0.177 10 false A 1.083,0.219 1.229,0.396 0.146,0.177 10 false A 3.125,1.854 3.271,2.031 0.146,0.177 10 false A 3.104,1.021 3.25,1.198 0.146,0.177 10 false A 0.823,2.604 0.969,2.781 0.146,0.177 10 false B 0.75,2.344 0.896,2.521 0.146,0.177 10 false B 2.625,2.417 2.771,2.594 0.146,0.177 10 false B 2.208,1.448 2.354,1.625 0.146,0.177 10 false D 2.375,1.323 2.521,1.5 0.146,0.177 10 false D 1.01,1.323 1.156,1.5 0.146,0.177 10 true E 0.406,2.01 0.552,2.188 0.146,0.177 10 false F 1.656,0.698 1.802,0.875 0.146,0.177 10 false F 0.854,1.042 1,1.219 0.146,0.177 10 false F 0.615,2 0.76,2.177 0.146,0.177 10 false D

Temporarily install the 26 bolts and nut.

Standard Bolt:
Item Length Thread Diameter
Bolt A 25 mm (0.984 in.) 8 mm (0.315 in.)
Bolt B 55 mm (2.17 in.) 8 mm (0.315 in.)
Bolt C 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt D 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt E 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt F 80 mm (3.15 in.) 10 mm (0.394 in.)


Text in Illustration
*1 Nut

NOTICE:

Make sure that there is no oil on the bolt threads.



h.
A214837E03
2.135,1.146 2.25,1.313 0.115,0.167 10 true 1 0.896,1.656 1.01,1.823 0.115,0.167 10 false 2 0.927,0.688 1.042,0.854 0.115,0.167 10 true 3

Tighten the 3 bolts in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.
A210020E02
1.938,0.052 2.083,0.25 0.146,0.198 10 true A 3.229,1.146 3.375,1.344 0.146,0.198 10 true B 0.771,0.5 0.917,0.698 0.146,0.198 10 true A 0.479,1.396 0.625,1.594 0.146,0.198 10 true A 2.885,1.74 3.031,1.938 0.146,0.198 10 true B

Temporarily install the fan bracket assembly with the 5 bolts to the timing chain cover sub-assembly.

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 80 mm (3.15 in.) 10 mm (0.394 in.)



j.

Temporarily install the V-ribbed belt tensioner assembly with the bolt and 6 mm hexagon bolt to the timing chain cover sub-assembly.


k.
U115393E01
1.635,0.042 1.76,0.219 0.125,0.177 10 false 4 2.281,0.719 2.406,0.896 0.125,0.177 10 false 5 2.865,1.385 2.99,1.563 0.125,0.177 10 false 6 2.99,1.146 3.115,1.323 0.125,0.177 10 false 7 2.438,0.292 2.563,0.469 0.125,0.177 10 true 8 1.375,0 1.5,0.177 0.125,0.177 10 false 9 0.177,1.063 0.365,1.24 0.188,0.177 10 false 10 2.646,1.552 2.833,1.729 0.188,0.177 10 false 11

Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


l.
A214839E03
0.635,1.906 0.833,2.083 0.198,0.177 10 false 12 1.75,0.677 1.948,0.854 0.198,0.177 10 false 13 0.646,2.104 0.844,2.281 0.198,0.177 10 false 19 2.542,2.677 2.74,2.854 0.198,0.177 10 false 18 2.625,2.396 2.823,2.573 0.198,0.177 10 false 17 1.531,2.031 1.729,2.208 0.198,0.177 10 true 16 1.073,1.552 1.271,1.729 0.198,0.177 10 true 15 2.063,1.75 2.26,1.927 0.198,0.177 10 true 14 0.698,2.323 0.896,2.5 0.198,0.177 10 false 20 1.458,0.458 1.656,0.635 0.198,0.177 10 false 28 0.271,1.021 0.469,1.198 0.198,0.177 10 false 27 0.323,1.906 0.521,2.083 0.198,0.177 10 false 26 2.177,3.042 2.375,3.219 0.198,0.177 10 false 25 1.448,3.073 1.646,3.25 0.198,0.177 10 false 22 1.781,3.073 1.979,3.25 0.198,0.177 10 false 24 1.031,3.021 1.229,3.198 0.198,0.177 10 false 23 0.792,2.594 0.99,2.771 0.198,0.177 10 false 21 2.469,1.677 2.667,1.854 0.198,0.177 10 true 30 1.063,0.219 1.26,0.396 0.198,0.177 10 false 29 3.031,1.031 3.229,1.208 0.198,0.177 10 false 34 3.219,1.771 3.417,1.948 0.198,0.177 10 false 33 2.198,0.188 2.396,0.365 0.198,0.177 10 false 32 1.917,0.427 2.115,0.604 0.198,0.177 10 false 31

Tighten the 22 bolts and nut labeled 12 to 34 in several steps in the sequence shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
A210033E02
1.26,0.396 0.865,1.573 0.865,1.573 2.094,0.396 false 0.771,1.625 0.938,1.844 0.167,0.219 10 false A

After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.



Hide 11202 4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Install 5 new gaskets to the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


b.

Install the cylinder head cover gasket LH to the cylinder head cover sub-assembly LH.

NOTICE:

Remove any oil from the contact surface.



c.
A291560

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A210022E02
1.927,1.521 2.052,1.688 0.125,0.167 10 true A

Install the cylinder head cover sub-assembly LH and a new seal washer with the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.

Install 5 new gaskets to the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


b.

Install the cylinder head cover gasket RH to the cylinder head cover sub-assembly RH.

NOTICE:

Remove any oil from the contact surface.



c.
A291561

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A210024E03
1.417,1.448 1.552,1.615 0.135,0.167 10 true A

Install the cylinder head cover sub-assembly RH and a new seal washer with the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 19500 6.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 8 ignition coils with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17363Q 7.CONNECT NO. 3 AIR TUBE

a.

Install a new gasket to the No. 3 air tube.


b.
U151671E02
1.479,3.125 1.729,3.125 1.729,3.125 1.917,2.917 false 1.229,2.406 1.583,2.406 1.583,2.406 1.875,2.219 false 1.25,2.771 1.635,2.771 1.635,2.771 2.073,2.615 false 1.052,2.323 1.219,2.5 0.167,0.177 10 false *1 1.042,2.708 1.208,2.875 0.167,0.167 10 false *a 1.26,3.063 1.427,3.229 0.167,0.167 10 false *2

Connect the No. 3 air tube with the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 No. 3 Air Tube
*2 Exhaust Manifold
*a Claw

NOTICE:

Make sure the gasket's claws are not caught between the No. 3 air tube and exhaust manifold.



c.

Install the wire harness clamp bracket with the bolt to the cylinder head cover sub-assembly RH.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17364A 8.CONNECT NO. 4 AIR TUBE

a.

Install a new gasket to the No. 4 air tube.


b.
A214883E02
0.509,2.206 0.693,2.379 0.184,0.173 10 *2 0.66,3.05 0.853,3.215 0.193,0.165 10 *a 2.655,2.292 2.529,2.292 2.529,2.292 2.283,2.588 false 0.749,2.294 0.929,2.294 0.929,2.294 1.17,2.569 false 0.902,3.151 1.147,3.151 1.147,3.151 1.544,2.767 false 2.684,2.197 2.868,2.371 0.184,0.173 10 *1

Connect the No. 4 air tube with the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 No. 4 Air Tube
*2 Exhaust Manifold
*a Claw

NOTICE:

Make sure the gasket's claws are not caught between the No. 4 air tube and exhaust manifold.



c.

Install the wire harness clamp bracket with the bolt to the cylinder head cover sub-assembly LH.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13471 9.INSTALL CRANKSHAFT PULLEY

a.
A164230E07
0.179,0.536 0.363,0.707 0.184,0.172 10 *a 0.626,1.593 0.820,1.756 0.194,0.163 10 *b 2.365,1.739 2.716,1.909 0.350,0.170 10 SST 2.032,1.354 2.322,1.813 false 2.322,1.813 1.814,1.466 false

Align the key groove of the crankshaft pulley with the crankshaft pulley set key, and slide on the crankshaft pulley to install it.

Text in Illustration
*a Hold
*b Turn


b.

Using SST, install the crankshaft pulley set bolt.

SST
09213-70011  
09330-00021  

Torque:
300 N*m (3059 kgf*cm, 221 ft.*lbf)


Hide 16603 10.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly to the timing chain cover sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16279 12.INSTALL NO. 3 WATER BY-PASS PIPE

HINT:

Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.


a.
A308526E02
0.938,1.573 1.063,1.573 1.063,1.573 1.271,1.156 false 0.885,1.073 1.188,1.073 false 0.677,0.969 0.875,1.125 0.198,0.156 10 true *a 0.708,1.479 0.906,1.635 0.198,0.156 10 true *b

Install the No. 3 water by-pass pipe to the front water by-pass joint with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a Stopper
*b Protrusion

NOTICE:

Align the notch of the stopper with the protrusion of the front water by-pass joint.



Hide 16355 13.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the front water by-pass joint to the cylinder head with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the No. 2 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.


Hide 16293 14.CONNECT NO. 10 WATER BY-PASS HOSE

a.
A380084E01
1.76,1.854 1.76,1.979 1.76,1.979 2.104,2.042 false 1.354,1.979 1.354,2.073 1.354,2.073 0.938,2.083 false 0.656,1.125 0.833,1.125 0.833,1.125 1.313,1.594 true 1.26,0.313 1.396,0.313 1.396,0.313 1.51,0.552 true 2.115,1.948 2.302,2.125 0.188,0.177 10 false *b 0.74,1.958 0.927,2.135 0.188,0.177 10 false *a 1.052,0.24 1.24,0.417 0.188,0.177 10 true *2

Connect the No. 10 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose
*a Paint Mark (Orange)
*b Paint Mark (Yellow)


Hide 16297 15.CONNECT NO. 9 WATER BY-PASS HOSE

a.

Connect the No. 9 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.


Hide 16323 16.INSTALL WATER INLET HOUSING

a.
A162555E05
0.493,0.13 0.681,0.305 0.188,0.174 10 *1 0.729,0.228 0.789,0.228 false 0.789,0.228 1.21,0.79 false

Install a new gasket to the timing chain cover sub-assembly.

Text in Illustration
*1 Gasket


b.

Install the water inlet housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16281F 17.CONNECT NO. 5 WATER BY-PASS HOSE

Hide 16296 18.CONNECT NO. 8 WATER BY-PASS HOSE

Hide 16206 19.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass hose to the water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


b.

Install the water by-pass pipe sub-assembly to the cylinder head cover sub-assembly RH with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 20.INSTALL AIR TUBE SUB-ASSEMBLY RH

a.

Install the air tube sub-assembly RH to the cylinder head cover sub-assembly RH with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16261G 21.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 44320 25.CONNECT VANE PUMP ASSEMBLY

A163333E10
1.667,1.854 1.49,1.854 1.49,1.854 0.896,1.635 true 1.708,1.771 1.885,1.948 0.177,0.177 10 true *a

a.

Connect the vane pump assembly to the timing chain cover sub-assembly with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Text in Illustration
*a Spacer

HINT:

Before performing the following procedures, move the spacer until the vane pump assembly can be installed.



Hide 11452 26.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15671 27.INSTALL OIL FILTER BRACKET

a.

Apply a light coat of engine oil to 2 new O-rings.


b.

Install the 2 O-rings to the timing chain cover sub-assembly.


c.

Install the oil filter bracket to the timing chain cover sub-assembly with the 2 nuts and 2 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 83520 28.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 88320 30.CONNECT COOLER COMPRESSOR ASSEMBLY

a.
A163332E01
2.93,1.786 3.058,1.951 0.128,0.165 10 2 3.071,1.054 3.199,1.219 0.128,0.165 10 3 2.779,1.349 2.907,1.514 0.128,0.165 10 1 2.254,1.782 2.382,1.947 0.128,0.165 10 4

Connect the cooler compressor assembly with the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the 2 bolts and 2 nuts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts and nuts in the order shown in the illustration to connect the cooler compressor assembly.



Hide 31.CONNECT HEATER HOSE AND NO. 1 WATER BY-PASS PIPE

a.

Connect the No. 1 water by-pass pipe with the 2 bolts to the cylinder head cover sub-assembly RH.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the heater hose to the water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


Hide 17343 32.CONNECT NO. 3 AIR INJECTION SYSTEM HOSE

a.

Connect the No. 3 air injection system hose to the air tube sub-assembly RH, and slide the clamp to secure the hose.


Hide 33.CONNECT ENGINE WIRE

a.

Connect the wire harness clamp bracket to the timing chain cover sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Engine Room RH Side:

i.

Connect the 9 clamps.


ii.

Connect the 2 air pump connectors.


iii.

Install the ground wire RH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iv.

Connect the noise filter connector.


v.

Connect the 2 VVT sensor connectors.


vi.

Connect the injector connector.


vii.

Connect the 4 ignition coil connectors.


viii.

Connect the 2 camshaft timing oil control valve connectors.


ix.

Connect the power steering oil pressure switch connector and solenoid valve connector.


x.

for 4WD:

Connect the clamp and junction connector.



c.

Engine Room LH Side:

i.

Connect the cooler compressor connector.


ii.

Connect the 6 clamps.


iii.

Connect the camshaft position sensor connector.


iv.

Connect the 2 camshaft timing oil control valve connectors.


v.

Connect the engine coolant temperature sensor connector.


vi.

Install the ground wire LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vii.

Connect the noise filter connector.


viii.

Connect the 2 VVT sensor connectors.


ix.

Connect the 4 ignition coil connectors.


x.

Connect the injector connector.


xi.

Connect the 2 wire harness clamps.


xii.

Connect the 4 air injection control driver connectors.


xiii.

Connect the 2 connectors and attach the 2 clamps to the engine room junction block.


xiv.

Install the engine room relay block cover.



Hide 25710 34.INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 2)

Hide 25710 36.INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 1)

Hide 17111 37.INSTALL INTAKE MANIFOLD

Hide 16400 38.INSTALL RADIATOR ASSEMBLY

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL