1.INSTALL STUD BOLT
Install the timing chain cover stud bolt.
Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
Install the oil pan stud bolt.
Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.
2.INSTALL RING PIN
Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.
| Item | Ring Pin Diameter | Specified Condition |
|---|---|---|
| Ring pin A | 13 mm (0.512 in.) | 7.5 to 8.5 mm (0.295 to 0.335 in.) |
| Ring pin B | 11 mm (0.433 in.) | 3.6 to 4.6 mm (0.142 to 0.181 in.) |
11381A
3.INSTALL REAR CRANKSHAFT OIL SEAL
Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.
0 to 1.0 mm (0 to 0.0394 in.)
Keep the lip free from foreign matter.
Do not tap on the oil seal at an angle.
12109A
4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the drain pipe.
Install the oil drain pipe with the bolt.
11381
5.INSTALL ENGINE REAR OIL SEAL RETAINER
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 to 3.0 mm (0.0787 to 0.118 in.)
3.5 mm (0.138 in.)
Remove any oil from the contact surface.
Install the engine rear oil seal retainer within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the oil seal retainer with the 6 bolts.
Do not start the engine for at least 2 hours after installing.
When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.
15104
6.INSTALL OIL STRAINER SUB-ASSEMBLY
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the oil strainer.
Install the oil strainer with the 2 bolts.
Make sure the O-ring is not twisted or damaged.
12121
7.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Install the baffle plate with the 7 bolts.
12101
8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the oil pan with the 14 bolts and 2 nuts.
Do not start the engine for at least 2 hours after installing.
12102A
9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.156 in.)
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the oil pan with the 14 bolts and 2 nuts.
Do not start the engine for at least 2 hours after installing.
16877
10.INSTALL NO. 1 HEAT EXCHANGER COVER
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surface.
Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the heat exchanger cover with the 12 bolts and 2 nuts.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 20 mm (0.787 in.) | 8 mm (0.315 in.) |
| Bolt B | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt C | 16 mm (0.630 in.) | 6 mm (0.236 in.) |
Do not start the engine for at least 2 hours after installing.
12203A
11.INSTALL VENTILATION PIPE GASKET
Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.
Do not tap the gasket at an angle.
Do not tap the gasket excessively.
12209E
12.INSTALL OIL RETURN PIPE GASKET
Install a new oil return pipe gasket.
11445
13.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the 2 water jacket spacers as shown in the illustration.
Face the cutouts indicated by the arrows in illustration away from the engine.
Face the "up mark" as shown in the illustration.
11115
14.INSTALL CYLINDER HEAD GASKET RH
11116
15.INSTALL CYLINDER HEAD GASKET LH
11101
16.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH
11102
17.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH
13716
18.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem caps.
Install the 32 valve stem caps to the cylinder head.
13750
19.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the valve lash adjuster (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION).
Install the 32 valve lash adjusters to the cylinder head.
Install the lash adjuster at the same place it was removed from.
13801
20.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Apply engine oil to the lash adjuster tips and valve stem cap ends.
Install the 32 valve rocker arms as shown in the illustration.
21.INSTALL CAMSHAFT BEARING CAP RH
11103C
22.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
23.INSTALL CAMSHAFT BEARING CAP LH
11104A
24.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
13521A
25.INSTALL CRANKSHAFT TIMING GEAR KEY
Install the timing gear key.
The other timing gear key will be installed at a later step.
13550
26.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
13506
27.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH
13561
28.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH
13559
29.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH
13540
30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH
13560A
31.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
13506
32.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH
13559
33.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH
13540
34.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH
13561
35.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH
13050
36.TIGHTEN CAMSHAFT TIMING GEAR
37.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION
Temporarily install the pulley set bolt.
Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.
Remove the crankshaft pulley set bolt.
16322
38.INSTALL WATER INLET PIPE
11302
39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
16100
40.INSTALL WATER PUMP ASSEMBLY
11301C
41.INSTALL FRONT CRANKSHAFT OIL SEAL
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal to a depth between 0 to 1.0 mm (0 to 0.0394 in.) from the timing chain cover edge.
Keep the lip free from foreign matter.
Do not tap oil seal at an angle.
13521A
42.INSTALL CRANKSHAFT TIMING GEAR KEY
Install the crankshaft timing gear key to the crankshaft.
11193
43.INSTALL SPARK PLUG TUBE GASKET
Using a cutter knife, cut off the seal part of the removed gasket.
Using the removed gasket and a hammer, tap in a new gasket until it stops.
If the removed gasket does not fit on the new one, correct the removed one with pliers.
Apply a light coat of MP grease to the gasket lip.
Return the 4 ventilation baffle plate claws to the original positions.
15678A
44.INSTALL OIL CONTROL VALVE FILTER
LH:
Install the valve filter in the cylinder head cover.
Install a new gasket and the cylinder head cover spacer with the 3 bolts.
RH:
Install the valve filter in the cylinder head cover.
Install a new gasket and the cylinder head cover spacer with the 3 bolts.
11201
45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).
Install the cover gasket to the cylinder head cover.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the cylinder head cover washer with a new seal and the 14 bolts.
Do not start the engine for at least 2 hours after the installation.
11202
46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).
Install the cover gasket to the cylinder head cover.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the cylinder head cover washer with a new seal and the 14 bolts.
Do not start the engine for at least 2 hours after the installation.
15330B
47.INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY
LH:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
RH:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
15100R
48.INSTALL CRANKSHAFT POSITION SENSOR
Install the crankshaft position sensor with the bolt.
19312
49.INSTALL CRANKSHAFT POSITION SENSOR PROTECTOR
Install the sensor protector with the 2 bolts.
11102A
50.INSTALL CAMSHAFT POSITION SENSOR
Install the camshaft position sensor with the bolt.
51.INSTALL VVT SENSOR
LH:
Install the 2 VVT sensors with the 2 bolts.
RH:
Install the 2 VVT sensors with the 2 bolts.
19100P
52.INSTALL SPARK PLUG
Using a 16 mm plug wrench, install the 8 spark plugs.
12185
53.INSTALL OIL FILLER CAP HOUSING
Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.
Install the cap housing with the 2 bolts.
12108
54.INSTALL OIL FILLER CAP SUB-ASSEMBLY
13471
55.INSTALL CRANKSHAFT PULLEY
15671
56.INSTALL OIL FILTER BRACKET
57.INSTALL OIL FILTER ELEMENT