Home › Engine / Hybrid System › 1UR-FE COOLING › WATER PUMP
RM27M0U _51 Engine / Hybrid System _049113 1UR-FE COOLING _0234064 WATER PUMP A

1UR-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL WATER PUMP ASSEMBLY

a.
A215872E02
1.75,0.01 1.885,0.156 0.135,0.146 10 false A 1.948,0.104 2.083,0.25 0.135,0.146 10 false A 2.458,1.5 2.615,1.688 0.156,0.188 10 true B 2.281,0.031 2.406,0.188 0.125,0.156 10 false C 2.854,1.406 2.99,1.573 0.135,0.167 10 true C 0.208,0.927 0.333,1.083 0.125,0.156 10 false C 2.115,1.958 2.302,2.146 0.188,0.188 10 true C 0.5,1.823 0.646,2 0.146,0.177 10 true C

Install a new gasket and the water pump assembly with the 8 bolts shown in the illustration.

Torque:
for bolt A : 47 N*m (479 kgf*cm, 35 ft.*lbf)
for bolt B : 23 N*m (235 kgf*cm, 17 ft.*lbf)
for bolt C : 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16173 2.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.
A210018E02
0.229,1.369 0.536,1.513 0.306,0.144 10 SST 0.616,1.458 0.699,1.458 0.699,1.458 1.064,1.149 false

Using SST, hold the water pump pulley and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16323 3.INSTALL WATER INLET HOUSING

a.

Install a new gasket to the water pump assembly.


b.
A215871

Install the water inlet housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16281F 4.CONNECT NO. 5 WATER BY-PASS HOSE

a.
A215870E01
1.527,0.288 1.858,0.438 0.331,0.150 10 45° 1.186,0.592 1.632,0.746 0.446,0.154 10 Front

Connect the No. 5 water by-pass hose.

HINT:

The direction of hose clamp is indicated in the illustration.



Hide 16296 5.CONNECT NO. 8 WATER BY-PASS HOSE

a.
A215868E01
0.54,0.579 0.927,0.717 0.387,0.138 10 Front

Connect the No. 8 water by-pass hose.

HINT:

The direction of hose clamp is indicated in the illustration.



Hide 16261G 6.INSTALL NO. 1 WATER BY-PASS HOSE

a.
A215866E01
0.08,0.588 0.465,0.730 0.385,0.142 10 Front 2.646,0.094 3.072,0.245 0.427,0.151 10 Top

Install the No. 1 water by-pass hose.

HINT:

The direction of hose clamp is indicated in the illustration.



Hide 16031 7.INSTALL WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

Hide 16711 8.INSTALL FAN SHROUD