1.INSTALL STRAIGHT PIN
Using a plastic-faced hammer, tap in the straight pins until their protrusion amounts are at the specified values shown in the illustration below.
| Item | a | b | c |
|---|---|---|---|
| for Straight Pin A | 19.5 to 20.5 mm
(0.768 to 0.807 in.) |
9.991 to 10.000 mm
(0.3934 to 0.3937 in.) |
9.5 to 10.0 mm
(0.374 to 0.393 in.) |
| for Straight Pin B | 15.6 to 15.8 mm
(0.615 to 0.622 in.) |
3.995 to 4.000 mm
(0.1574 to 0.3940 in.) |
5.6 to 6.2 mm
(0.221 to 0.244 in.) |
| *a | for Straight Pin A | *b | for Straight Pin B |
41311A
2.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING
Using SST and a press, press in the bearing.
Using a snap ring expander, install a new snap ring.
41304F
3.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
Install the side gear shaft into the differential tube.
Using snap ring pliers, install a new snap ring.
41304P
4.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
Using SST and a plastic-faced hammer, tap in a new oil seal.
4.8 to 5.8 mm (0.189 to 0.228 in.)
Coat the lip of the oil seal with MP grease.
41434
5.INSTALL DIFFERENTIAL CLUTCH HUB
Install the clutch hub onto the side gear inter shaft.
Using snap ring pliers, install a new snap ring.
Be sure to install the differential clutch hub in the correct direction.
Install the differential clutch sleeve to the side gear shaft.
41331G
6.INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING
Using SST and a press, press in 2 new bearings.
1.2 to 1.8 mm (0.0473 to 0.0708 in.)
41311
7.INSTALL FRONT DIFFERENTIAL CASE
Install the 2 side gear thrust washers onto the 2 side gears.
Using the table below, select the thrust washer which will ensure that the backlash is within the specifications.
| Thickness | Thickness |
|---|---|
| 1.43 to 1.47 mm (0.0563 to 0.0578 in.) | 1.68 to 1.72 mm (0.0662 to 0.0677 in.) |
| 1.48 to 1.52 mm (0.0583 to 0.0598 in.) | 1.73 to 1.77 mm (0.0682 to 0.0696 in.) |
| 1.53 to 1.57 mm (0.0603 to 0.0618 in.) | 1.78 to 1.82 mm (0.0701 to 0.0716 in.) |
| 1.58 to 1.62 mm (0.0622 to 0.0637 in.) | 1.83 to 1.87 mm (0.0721 to 0.0736 in.) |
| 1.63 to 1.67 mm (0.0642 to 0.0657 in.) | - |
Install the 2 side gears, 2 side gear thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.
Align the holes of the differential case assembly and pinion shaft.
Apply hypoid gear oil to each sliding surface and rotating part.
Measure the side gear backlash.
Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.
0.1 to 0.25 mm (0.00394 to 0.00984 in.)
If the backlash is not within the specification, install a side gear thrust washer with a different thickness.
Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.
Stake the differential case.
8.INSTALL DIFFERENTIAL RING GEAR
Clean the contact surfaces of the differential case and ring gear.
Heat the ring gear to about 100°C (212°F) in boiling water.
Carefully take the ring gear out of the boiling water.
After the moisture on the ring gear has completely evaporated, quickly set the ring gear onto the differential case.
Align the matchmarks on the ring gear and differential case.
Temporarily install the 12 bolts so that the bolt holes in the ring gear and differential case are aligned.
After the ring gear cools down sufficiently, apply adhesive to the bolts and install them.
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
41311A
9.INSTALL FRONT DIFFERENTIAL CASE BEARING
Using SST and a press, press in the 2 bearings (inner race).
41311A
10.INSTALL FRONT DIFFERENTIAL CASE BEARING
When replacing the 2 differential case bearings, fit the thinnest washer to each bearing. When reusing the bearings, fit a washer of the same thickness as the one removed to each bearing.
Install a new plate washer to the bearing retainer.
| *1 | Plate Washer |
Using SST and a press, install the bearing (outer race) onto the bearing retainer.
Install a new plate washer onto the differential carrier.
| *1 | Plate Washer |
Using SST and a press, press in the bearing (outer race) onto the differential carrier assembly.
41211B
11.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING
Using SST, install the bearing (outer race).
41211A
12.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST, install the washer and bearing (outer race).
| *1 | Plate Washer |
First, fit a washer of the same thickness as the removed washer, then after checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.
41183C
13.INSTALL FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR
Install the front differential breather plug oil deflector with the 2 bolts.
41211A
14.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a press, press in the bearing (inner race).
15.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION
41211B
16.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING
Using SST and a hammer, lightly tap in the bearing (inner race) to install it.
41214C
17.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
18.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Using SST, install the companion flange.
| *a | Turn |
| *b | Hold |
Coat the threads of the nut with hypoid gear oil LSD.
Using SST to hold the companion flange.
Tighten the nut until the standard preload is reached.
or less
As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Specified Condition |
|---|---|
| New | 2.69 to 3.19 N*m (28 to 32 kgf*cm, 24 to 28 in.*lbf) |
| Reused | 1.86 to 2.17 N*m (19 to 22 kgf*cm, 17 to 19 in.*lbf) |
If necessary, disassemble and inspect the differential assembly.
41311
19.INSTALL FRONT DIFFERENTIAL CASE
Remove the bearing retainer.
Install the differential case to the differential carrier.
41141L
20.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER
Install the differential cross shaft bearing retainer and differential support with the 14 bolts.
41110V
21.INSTALL FRONT DIFFERENTIAL UNION
Install the front differential union.
22.ADJUST BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
Using SST and a dial indicator, measure the ring gear backlash.
0.17 to 0.27 mm (0.00670 to 0.01062 in.)
If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
There should be no clearance between the plate washer and differential case.
Make sure that there is ring gear backlash.
| Thickness | Thickness |
|---|---|
| 1.49 to 1.51 mm (0.0587 to 0.0594 in.) | 1.93 to 1.95 mm (0.0760 to 0.0767 in.) |
| 1.51 to 1.53 mm (0.0595 to 0.0602 in.) | 1.95 to 1.97 mm (0.0768 to 0.0775 in.) |
| 1.53 to 1.55 mm (0.0603 to 0.0610 in.) | 1.97 to 1.99 mm (0.0776 to 0.0783 in.) |
| 1.55 to 1.57 mm (0.0611 to 0.0618 in.) | 1.99 to 2.01 mm (0.0784 to 0.0791 in.) |
| 1.57 to 1.59 mm (0.0619 to 0.0625 in.) | 2.01 to 2.03 mm (0.0792 to 0.0799 in.) |
| 1.59 to 1.61 mm (0.0626 to 0.0633 in.) | 2.03 to 2.05 mm (0.0800 to 0.0807 in.) |
| 1.61 to 1.63 mm (0.0634 to 0.0641 in.) | 2.05 to 2.07 mm (0.0808 to 0.0814 in.) |
| 1.63 to 1.65 mm (0.0642 to 0.0649 in.) | 2.07 to 2.09 mm (0.0815 to 0.0822 in.) |
| 1.65 to 1.67 mm (0.0650 to 0.0657 in.) | 2.09 to 2.11 mm (0.0823 to 0.0830 in.) |
| 1.67 to 1.69 mm (0.0658 to 0.0665 in.) | 2.11 to 2.13 mm (0.0831 to 0.0838 in.) |
| 1.69 to 1.71 mm (0.0666 to 0.0673 in.) | 2.13 to 2.15 mm (0.0839 to 0.0846 in.) |
| 1.71 to 1.73 mm (0.0674 to 0.0681 in.) | 2.15 to 2.17 mm (0.0847 to 0.0854 in.) |
| 1.73 to 1.75 mm (0.0682 to 0.0688 in.) | 2.17 to 2.19 mm (0.0855 to 0.0862 in.) |
| 1.75 to 1.77 mm (0.0689 to 0.0696 in.) | 2.19 to 2.21 mm (0.0863 to 0.0870 in.) |
| 1.77 to 1.79 mm (0.0697 to 0.0704 in.) | 2.21 to 2.23 mm (0.0871 to 0.0877 in.) |
| 1.79 to 1.81 mm (0.0705 to 0.0712 in.) | 2.23 to 2.25 mm (0.0878 to 0.0885 in.) |
| 1.81 to 1.83 mm (0.0713 to 0.0720 in.) | 2.25 to 2.27 mm (0.0886 to 0.0893 in.) |
| 1.83 to 1.85 mm (0.0721 to 0.0728 in.) | 2.27 to 2.29 mm (0.0894 to 0.0901 in.) |
| 1.85 to 1.87 mm (0.0729 to 0.0736 in.) | 2.29 to 2.31 mm (0.0902 to 0.0909 in.) |
| 1.87 to 1.89 mm (0.0737 to 0.0744 in.) | 2.31 to 2.33 mm (0.0910 to 0.0917 in.) |
| 1.89 to 1.91 mm (0.0745 to 0.0751 in.) | 2.33 to 2.35 mm (0.0918 to 0.0925 in.) |
| 1.91 to 1.93 mm (0.0752 to 0.0759 in.) | - |
23.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Bearing | Specified Condition |
|---|---|
| New | 4.30 to 5.60 N*m (44 to 57 kgf*cm, 39 to 49 in.*lbf) |
| Reused | 3.19 to 4.30 N*m (33 to 43 kgf*cm, 29 to 38 in.*lbf) |
Record the differential ring gear preload.
If necessary, disassemble and inspect the differential.
24.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
Remove the bearing retainer and differential case.
Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.
Install the differential case to the differential carrier.
Install the differential cross shaft bearing retainer and front differential front support assembly LH with the 14 bolts.
Hold the companion flange firmly and rotate the ring gear in both directions.
Remove the differential case, side bearing retainer and differential case.
Inspect the tooth contact pattern.
| *a | Proper Contact | *b | Heel Contact |
| *c | Face Contact | *d | Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c) |
| *e | Toe Contact | *f | Flank Contact |
| *g | Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) | - | - |
If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.
| Thickness | Thickness |
|---|---|
| 1.815 to 1.835 mm (0.0715 to 0.0722 in.) | 2.065 to 2.085 mm (0.0813 to 0.0820 in.) |
| 1.840 to 1.860 mm (0.0725 to 0.0732 in.) | 2.090 to 2.110 mm (0.0823 to 0.0830 in.) |
| 1.865 to 1.885 mm (0.0735 to 0.0742 in.) | 2.115 to 2.135 mm (0.0833 to 0.0840 in.) |
| 1.890 to 1.910 mm (0.0744 to 0.0751 in.) | 2.140 to 2.160 mm (0.0843 to 0.0850 in.) |
| 1.915 to 1.935 mm (0.0754 to 0.0761 in.) | 2.165 to 2.185 mm (0.0853 to 0.0860 in.) |
| 1.940 to 1.960 mm (0.0764 to 0.0771 in.) | 2.190 to 2.210 mm (0.0863 to 0.0870 in.) |
| 1.965 to 1.985 mm (0.0774 to 0.0781 in.) | 2.215 to 2.235 mm (0.0872 to 0.0879 in.) |
| 1.990 to 2.010 mm (0.0784 to 0.0791 in.) | 2.240 to 2.260 mm (0.0882 to 0.0889 in.) |
| 2.015 to 2.035 mm (0.0794 to 0.0801 in.) | 2.265 to 2.285 mm (0.0892 to 0.0899 in.) |
| 2.040 to 2.060 mm (0.0804 to 0.0811 in.) | - |
41204E
25.REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT
41204D
26.REMOVE FRONT DRIVE PINION FRONT COMPANION FLANGE SUB-ASSEMBLY
41214C
27.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41141L
28.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER
41311
29.REMOVE FRONT DIFFERENTIAL CASE
30.REMOVE DIFFERENTIAL DRIVE PINION
41211B
31.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
41231F
32.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new bearing spacer.
33.TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION
41311
34.INSTALL FRONT DIFFERENTIAL CASE
41141L
35.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER
Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.
| *a | Seal Packing |
Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.
Apply seal packing to the differential carrier as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
2.0 to 3.0 mm (0.0788 to 0.118 in.)
Install the side bearing retainer within 10 minutes of applying seal packing.
Install the front differential cross shaft bearing retainer and front differential front support assembly LH with the 11 bolts (A), and 3 bolts (B).
Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.
41211B
36.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING
Using SST and a hammer, lightly tap in the bearing (inner race) to install it.
41214C
37.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41101D
38.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
Using SST and a hammer, tap in a new oil seal.
5.6 to 6.6 mm (0.221 to 0.259 in.)
Coat the lip of the oil seal with MP grease.
41204D
39.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, install the companion flange.
| *a | Turn |
| *b | Hold |
Using SST to hold the companion flange.
Coat the threads of a new nut with hypoid gear oil LSD.
Install the nut by tightening it until the standard preload is reached.
or less
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Bearing | Specified Condition |
|---|---|
| New | 3.05 to 3.55 N*m (32 to 36 kgf*cm, 27 to 31 in.*lbf) |
| Reused | 2.22 to 2.53 N*m (23 to 25 kgf*cm, 20 to 22 in.*lbf) |
If the preload is more than the specification, replace the bearing spacer.
If the preload is less than the specification, tighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.
or less
If the maximum torque is exceeded while tightening the nut, replace the bearing spacer and repeat the preload procedure.
Do not loosen the nut to reduce the preload.
40.INSPECT TOTAL PRELOAD
With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.
| Bearing | Specified Condition |
|---|---|
| New | 4.66 to 5.96 N*m (48 to 60 kgf*cm, 42 to 52 in.*lbf) |
| Reused | 3.55 to 4.66 N*m (37 to 47 kgf*cm, 32 to 41 in.*lbf) |
41.INSPECT BACKLASH BETWEEN DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
Using SST and a dial indicator, measure the ring gear backlash.
0.17 to 0.27 mm (0.00670 to 0.0106 in.)
41204D
42.INSPECT RUNOUT OF FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| *a | 55 mm (2.17 in.) |
| Runout | Specified Condition |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
If the runout is more than the maximum, replace the companion flange.
41204E
43.STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT
Using a chisel and hammer, stake the nut.
41304P
44.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.
Coat the lip of the oil seal with MP grease.
-0.45 to 0.45 mm (-0.0177 to 0.0177 in.)
41306F
45.INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY
Install a new snap ring onto the side gear inter shaft.
Using a plastic-faced hammer, install the side gear inter shaft onto the differential case.
Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of play in the axial direction.
Check that the side gear inter shaft does not come out when trying to pull it out by hand.
41320
46.INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY
Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and bearing retainer.
| *a | Seal Packing |
Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.
Apply seal packing to the bearing retainer as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Install the differential tube within 10 minutes of applying seal packing.
Install the differential tube onto the bearing retainer.
Clean the threads of 4 new bolts and the retainer bolt holes with toluene or trichloroethylene.
Apply adhesive to 2 to 3 threads of each bolt end.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the 4 bolts.
Do not add oil or drive the vehicle immediately after installing the cover, and leave it as is for at least an hour. Also, for 12 hours or less, avoid rapid acceleration/deceleration.
41400
47.INSPECT DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY
41400
48.INSTALL DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY
Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and actuator.
| *a | Seal Packing |
Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.
Apply seal packing to the differential tube as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Install the actuator within 10 minutes of applying seal packing.
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Install the actuator to the differential tube.
Install the 4 bolts.