Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

When the transfer is switching between 4H and 4L, the H4 and L4 terminals of the transfer indicator switch are in one of the ON/OFF combinations listed in the table below.

Terminal In 4H Switching between 4H and 4L In 4L
H4 OFF (OPEN) ON (GND) ON (GND)
L4 OFF (OPEN) OFF (OPEN) ON (GND)

This DTC is detected when the 4WD HIGH position and 4WD LOW position judgment signals do not match.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P2772
1.

Ignition switch is ON and engine is running

2.

H4 terminal signal is OFF (OPEN) and L4 terminal signal is ON (GND)

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer indicator switch



WIRING DIAGRAM

C290929E01
1.906,0.573 2.365,0.771 0.458,0.198 10 false A24 1.906,0.75 2.365,0.948 0.458,0.198 10 false ECM 0.615,1.604 1.073,1.802 0.458,0.198 10 false D70 0.615,1.802 1.708,2.26 1.094,0.458 10 false Transfer Indicator Switch 0.885,3.333 2.167,3.552 1.281,0.219 10 false Transfer Assembly 5.135,3.177 5.594,3.375 0.458,0.198 10 false A26 5.156,3.354 6.938,3.573 1.781,0.219 10 false 4 Wheel Drive Control ECU 5.573,2.458 6.031,2.656 0.458,0.198 10 false H4 5.563,1.938 6.021,2.135 0.458,0.198 10 false L4 5.25,1.854 5.708,2.052 0.458,0.198 10 false 13 5.24,2.313 5.698,2.51 0.458,0.198 10 false 12 3.469,0.5 3.927,0.698 0.458,0.198 10 false 21 3.156,0.625 3.615,0.823 0.458,0.198 10 false L4 3.135,1.823 3.594,2.021 0.458,0.198 10 false L4 3.135,2.313 3.594,2.51 0.458,0.198 10 false H4 3.469,1.813 3.927,2.01 0.458,0.198 10 false 2 3.448,2.302 3.906,2.5 0.458,0.198 10 false 1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER INDICATOR SWITCH)
a.

Disconnect the A26 4 wheel drive control ECU connector.


b.

Disconnect the D70 transfer indicator switch connector.


c.

Disconnect the A24 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-13 (L4) - D70-2 (L4) Always Below 1 Ω
A26-12 (H4) - D70-1 (H4) Always Below 1 Ω
A26-13 (L4), D70-2 (L4) or A24-21 (L4) - Body ground Always 10 kΩ or higher
A26-12 (H4) or D70-1 (H4) - Body ground Always 10 kΩ or higher
A26-13 (L4), D70-2 (L4) or A24-21 (L4) - A26-12 (H4) or D70-1 (H4) Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
U152645E02
1.719,1.854 2.292,2.854 false 1.427,1.854 1,2.927 false 0.146,0.083 0.385,0.333 0.24,0.25 10 false *a 2.25,2.875 2.49,3.073 0.24,0.198 10 false L4 0.875,2.938 1.125,3.135 0.25,0.198 10 false H4 0.333,1.781 0.656,1.969 0.323,0.188 10 false D70

a.

Disconnect the A24 ECM connector.


b.

Disconnect the transfer indicator switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D70-2 (L4) - Body ground Ignition switch ON 4 to 6 V
D70-1 (H4) - Body ground Ignition switch ON 4 to 6 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Indicator Switch)

NOTICE:

Turning the ignition switch on with the ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.




OK

REPLACE TRANSFER INDICATOR SWITCH

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU