Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A0  Automatic Disconnecting Differential Motor Control Circuit Open  P17A1  Automatic Disconnecting Differential Motor Control Circuit Low  


DESCRIPTION

This DTC is detected when an open circuit or short to ground in the A.D.D. shift motor drive circuit is detected.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A0
1.

Ignition switch ON (when not switching between 2WD and 4H)

2.

Open circuit in the A.D.D. shift motor drive circuit

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

A.D.D. actuator (differential vacuum actuator assembly)


P17A1
1.

Ignition switch ON (when not switching between 2WD and 4H)

2.

Short to ground in the A.D.D. shift motor drive circuit

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

A.D.D. actuator (differential vacuum actuator assembly)



WIRING DIAGRAM

C290925E01
1.021,1.052 1.844,1.49 0.823,0.438 10 false A.D.D. Shift Motor 2.146,0.635 2.604,0.833 0.458,0.198 10 false DM1 2.135,1.302 2.594,1.5 0.458,0.198 10 false DM2 4.635,1.99 5.094,2.188 0.458,0.198 10 false A25 0.813,2.125 2.667,2.5 1.854,0.375 10 false A.D.D. Actuator (Differential Vacuum Actuator Assembly) 0.802,1.969 1.26,2.167 0.458,0.198 10 false G1 4.635,2.188 6.354,2.385 1.719,0.198 10 false 4 Wheel Drive Control ECU 4.948,0.74 5.406,0.938 0.458,0.198 10 false DM1 4.948,1.448 5.406,1.646 0.458,0.198 10 false DM2 2.583,0.667 2.74,0.865 0.156,0.198 10 false 1 4.729,0.646 4.885,0.844 0.156,0.198 10 false 1 4.729,1.333 4.885,1.531 0.156,0.198 10 false 2 2.563,1.333 2.719,1.531 0.156,0.198 10 false 2

PROCEDURE

1.CHECK DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (A.D.D. SHIFT MOTOR)
U151874E02
1.146,1.542 0.594,2.427 false 1.49,1.552 1.938,2.479 false 1.667,0.563 1.979,0.719 0.313,0.156 10 false A25 0.396,2.448 0.74,2.677 0.344,0.229 10 false DM1 1.844,2.49 2.188,2.719 0.344,0.229 10 false DM2 0.188,0.104 0.521,0.333 0.333,0.229 10 false *a

a.

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 (DM1) - A25-2 (DM2) Always 2 Ω or less
A25-1 (DM1) or A25-2 (DM2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY)
a.

Disconnect the A25 4 wheel drive control ECU connector.


b.

Disconnect the G1 A.D.D. actuator (differential vacuum actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 (DM1) - G1-1 (DM1) Always Below 1 Ω
A25-2 (DM2) - G1-2 (DM2) Always Below 1 Ω
A25-1 (DM1) or G1-1 (DM1) - Body ground Always 10 kΩ or higher
A25-2 (DM2) or G1-2 (DM2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR