Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A4  Automatic Disconnecting Differential Motor Limit Switch Circuit  


DESCRIPTION

When the A.D.D. actuator is switching between 2WD and 4WD, the DL1 and DL2 terminals of the limit switch are in one of the ON/OFF combinations listed in the table below.

Terminal In 2WD Switching between 2WD and 4WD In 4WD
DL1 OFF (OPEN) ON (GND) ON (GND)
DL2 ON (GND) ON (GND) OFF (OPEN)

This DTC is detected when the limit switch ON/OFF combination (2 lines) is abnormal.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A4
1.

Ignition switch is ON and engine is running

2.

Limit switch DL1 terminal is OFF (OPEN) and the DL2 terminal is OFF (OPEN)

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

A.D.D. actuator (differential vacuum actuator assembly)



WIRING DIAGRAM

C290926E01
3.073,0.771 3.531,0.969 0.458,0.198 10 false DL1 3.052,1.229 3.51,1.427 0.458,0.198 10 false DL2 3.01,2.208 3.469,2.406 0.458,0.198 10 false ADD 2.021,1.802 2.927,1.979 0.906,0.177 10 false Limit Switch 1.573,2.594 3.156,2.771 1.583,0.177 10 false A.D.D. Detection Switch 1.25,2.198 1.708,2.396 0.458,0.198 10 false GND 0.875,2.979 1.333,3.177 0.458,0.198 10 false G1 0.865,3.135 3.198,3.51 2.333,0.375 10 false A.D.D. Actuator (Differential Vacuum Actuator Assembly) 4.75,3.031 5.208,3.229 0.458,0.198 10 false A25 4.75,3.219 6.573,3.448 1.823,0.229 10 false 4 Wheel Drive Control ECU 5.031,2.323 5.49,2.521 0.458,0.198 10 false ADD 5.042,1.375 5.5,1.573 0.458,0.198 10 false DL2 5.042,0.885 5.5,1.083 0.458,0.198 10 false DL1 4.708,1.24 5.021,1.438 0.313,0.198 10 false 20 4.729,2.198 5.042,2.396 0.313,0.198 10 false 18 4.74,0.771 5.052,0.969 0.313,0.198 10 false 7 3.49,0.771 3.802,0.969 0.313,0.198 10 false 6 3.49,1.24 3.802,1.438 0.313,0.198 10 false 5 3.479,2.198 3.792,2.396 0.313,0.198 10 false 3 1.031,2.198 1.344,2.396 0.313,0.198 10 false 4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY)
a.

Disconnect the A25 4 wheel drive control ECU connector.


b.

Disconnect the G1 A.D.D. actuator (differential vacuum actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-7 (DL1) - G1-6 (DL1) Always Below 1 Ω
A25-20 (DL2) - G1-5 (DL2) Always Below 1 Ω
G1-4 (GND) - Body ground Always Below 1 Ω
A25-7 (DL1) or G1-6 (DL1) - Body ground Always 10 kΩ or higher
A25-20 (DL2) or G1-5 (DL2) - Body ground Always 10 kΩ or higher




OK

2.INSPECT DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (LIMIT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (LIMIT SWITCH)
C290971E03
1.417,1.865 1.719,2.688 false 1.094,1.865 0.646,2.708 false 0.208,0.198 0.458,0.417 0.25,0.219 10 false *a 1.646,2.698 1.979,2.865 0.333,0.167 10 false DL2 0.521,2.74 0.854,2.948 0.333,0.208 10 false DL1

a.

Disconnect the G1 A.D.D. actuator (differential vacuum actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (DL1) - Body ground Always 10 kΩ or higher
5 (DL2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(A.D.D. Actuator [Differential Vacuum Actuator Assembly])



OK

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU