Home › Drivetrain › WF1AM TRANSFER › TRANSFER ASSEMBLY
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234108 TRANSFER ASSEMBLY A

WF1AM TRANSFER  TRANSFER ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Coat all of the sliding and rotating surfaces with Toyota Genuine Transfer gear oil LF 75W or equivalent before reassembly.


PROCEDURE

Hide 36111B 1.INSTALL TRANSFER CASE OIL SEAL

a.
C291178E01
1.013,1.112 1.198,0.631 1.198,0.631 1.297,0.631 false 1.116,1.344 1.198,0.631 false 1.335,0.541 1.665,0.711 0.330,0.170 10 SST 2.955,0.855 3.118,1.024 0.163,0.170 10 A

Using SST and a hammer, tap in a new transfer case oil seal as shown in the illustration.

SST
09950-60010  (09951-00630)
09950-70010  (09951-07100)

Drive in depth (A):

1.4 to 2.4 mm (0.056 to 0.094 in.)


NOTICE:

Be careful not to damage or deform the transfer case oil seal.



Hide 36292A 2.INSTALL TRANSFER DRIVEN SPROCKET BEARING (FRONT)

a.
C291180E01
0.979,1.246 1.181,0.614 1.181,0.614 1.267,0.614 false 1.077,1.456 1.181,0.614 false 1.297,0.528 1.637,0.712 0.340,0.184 10 SST 2.538,1.387 2.74,0.756 2.74,0.756 2.826,0.756 false 2.856,0.67 3.196,0.853 0.340,0.184 10 SST

Using SST and a press, press in a new transfer driven sprocket bearing (front) as shown in the illustration.

SST
09950-60010  (09951-00390, 09952-06010)
09950-60020  (09951-00910)
09950-70010  (09951-07100)

NOTICE:

The transfer driven sprocket bearing (front) should be installed completely.



Hide 36111X 3.INSTALL NO. 2 TRANSFER CASE OIL SEAL

a.
C291179E01
1.176,0.945 1.552,0.171 1.552,0.171 1.683,0.171 false 1.215,1.869 1.552,0.171 false 1.746,0.093 2.092,0.276 0.346,0.184 10 SST 2.967,1.158 3.197,1.342 0.230,0.184 10 A

Using SST and a press, press in a new No. 2 transfer case oil seal as shown in the illustration.

SST
09316-12010  
09513-36040  

Drive in depth (A):

1.5 to 2.5 mm (0.060 to 0.098 in.)


NOTICE:

Be careful not to damage or deform the No. 2 transfer case oil seal.



Hide 33309B 4.INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)

a.
C291170

Install the output shaft companion flange sub-assembly (front).


b.

Using a snap ring expander, install the shaft snap ring.


Hide 5.INSTALL TRANSFER OIL SEPARATOR

a.
C291201

Using a T25 ''TORX'' socket wrench, install the bolt and transfer oil separator.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 36273 6.INSPECT TRANSFER LOWER PLANETARY RING GEAR

a.
C291169E02
2.344,0.927 2.615,1.594 2.615,1.594 2.708,1.594 false 2.75,1.51 2.948,1.698 0.198,0.188 10 false *a

Install the transfer lower planetary ring gear.


b.

Using a screwdriver, install the transfer lower planetary ring gear hole snap ring.

Text in Illustration
*a Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 36270 7.INSTALL TRANSFER LOWER PLANETARY GEAR ASSEMBLY

a.
C291181E01
0.914,0.585 0.665,0.585 false 0.261,0.508 0.587,0.688 0.326,0.180 10 SST

Using SST and a press, press in a new transfer input gear radial ball bearing.

SST
09214-76011  

NOTICE:

The transfer input gear radial ball bearing should be installed completely.



b.
C291167

Install the transfer lower planetary gear assembly.


Hide 36235 8.INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
U152631E01
2.047,0.883 2.297,1.108 0.251,0.225 10 *1 1.544,0.986 1.985,0.986 false 1.852,1.348 2.102,1.572 0.251,0.225 10 *2 1.429,1.748 1.647,1.45 1.647,1.45 1.79,1.45 false 1.663,1.978 1.913,2.202 0.251,0.225 10 *3 1.24,2.378 1.458,2.08 1.458,2.08 1.601,2.08 false 0.262,2.523 0.513,2.748 0.251,0.225 10 *a

Install the transfer lower planetary gear bearing, the No. 2 transfer output shaft spacer and the transfer high and low clutch sleeve.

Text in Illustration
*1 Transfer High and Low Clutch Sleeve
*2 No. 2 Transfer Output Shaft Spacer
*3 Transfer Lower Planetary Gear Bearing
*a Transfer Lower Planetary Gear Assembly Side

NOTICE:

Make sure that the transfer lower planetary gear bearing is installed facing the correct direction.



Hide 36231 9.INSTALL REAR TRANSFER OUTPUT SHAFT

a.
C291165

Install the rear transfer output shaft.


Hide 36311F 10.INSTALL NO. 1 TRANSFER GEAR SHIFT FORK

a.
C291207

Install the 2 gear shift fork pads to the No. 1 transfer gear shift fork.


b.
C291164

Install the No. 1 transfer gear shift fork.


Hide 33449D 11.INSTALL TRANSFER CASE MAGNET

a.
C291163

Install the transfer case magnet.


Hide 36106K 12.INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY

a.
C291162E02
2.646,0.865 2.646,0.167 2.646,0.167 2.854,0.167 false 1.5,1.427 1.5,1.948 1.5,1.948 1.292,1.948 false 0.677,1.365 0.677,1.885 0.677,1.885 0.604,1.885 false 2.906,0.073 3.094,0.26 0.188,0.188 10 false *1 1.125,1.865 1.313,2.052 0.188,0.188 10 false *2 0.427,1.792 0.615,1.979 0.188,0.188 10 false *3

Install the transfer oil strainer sub-assembly to the transfer oil tube.


b.

Install the transfer oil tube to the transfer oil pump body sub-assembly.


c.

Install the transfer oil pump body sub-assembly together with the transfer oil tube and transfer oil strainer sub-assembly.

Text in Illustration
*1 Transfer Oil Pump Body Sub-assembly
*2 Transfer Oil Tube
*3 Transfer Oil Strainer Sub-assembly


d.

Using a T25 ''TORX'' socket wrench, install the bolt.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 36205 13.INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C291161

Install the transfer drive sprocket sub-assembly and transfer driven sprocket to the front transfer drive chain.


b.

Install the transfer drive sprocket sub-assembly together with the front transfer drive chain and transfer driven sprocket.

NOTICE:

Do not drop the transfer drive sprocket sub-assembly, front transfer drive chain and transfer driven sprocket.



Hide 33806 14.INSTALL CONTROL SELECT SHAFT SUB-ASSEMBLY

a.

Install the control select shaft sub-assembly.

NOTICE:

When removing the rear transfer case, the spring of the control select shaft sub-assembly may become detached. Check the condition of the spring before installing the control select shaft sub-assembly, and if the spring is not in the correct position, correct the spring as shown in the illustration.


CAUTION:
·

Wear protective gloves to avoid injuries to your hands.

·

Take care when performing this procedure as the spring is under high tension.



i.
C291189E02
2.333,0.844 2.698,1.219 2.698,1.219 2.833,1.219 false 2.917,2.896 2.979,2.333 2.979,2.333 3.115,2.333 false 0.25,1.635 0.385,1.833 0.135,0.198 10 false A 1.313,0.354 1.448,0.552 0.135,0.198 10 false B 2.875,1.135 3.083,1.333 0.208,0.198 10 false *a 1.323,3.531 1.427,3.729 0.104,0.198 10 true C 3.146,2.24 3.354,2.438 0.208,0.198 10 false *b 1.781,2.948 1.917,3.146 0.135,0.198 10 false A 0.708,3.76 0.844,3.958 0.135,0.198 10 false B

Make sure the spring is positioned as indicated by arrows A and B, and then rotate the control select shaft in the direction indicated by the arrow shown in the illustration.


ii.

Rotate the control select shaft until the part of the spring indicated by arrow A moves past the part indicated by arrow B.


iii.

Slide the control select shaft in the direction indicated by arrow C in the illustration to return the spring to the correct position.

Text in Illustration
*a Part of the Spring Shown by Arrow A in the Open Position
*b Control Select Shaft Sub-assembly in Correct Position



b.
C291214E01
1.85,1.011 2.649,0.105 2.649,0.105 2.911,0.105 false 2.98,0.015 3.146,0.177 0.166,0.163 10 *1 1.609,0.681 1.115,0.109 1.115,0.109 0.853,0.109 false 0.643,0.032 0.809,0.195 0.166,0.163 10 *2

Install the No. 1 transfer gear shift fork to the side of the control select shaft sub-assembly as shown in the illustration.

Text in Illustration
*1 No. 1 Transfer Gear Shift Fork
*2 Control Select Shaft Sub-assembly


Hide 35285B 15.INSTALL SOLENOID LOCK PLATE WITH NO. 2 TRANSFER GEAR SHIFT FORK

a.
C291158E01
1.851,0.675 1.851,0.095 1.851,0.095 1.954,0.095 false 1.99,0.024 2.184,0.204 0.194,0.180 10 *2 2.886,0.533 2.886,0.327 2.886,0.327 2.989,0.327 false 3.026,0.256 3.220,0.436 0.194,0.180 10 *1

Install the No. 2 transfer gear shift fork to the solenoid lock plate.


b.

Install the solenoid lock plate together with the No. 2 transfer gear shift fork.

Text in Illustration
*1 Solenoid Lock Plate Assembly
*2 No. 2 Transfer Gear Shift Fork Sub-assembly


Hide 36314 16.INSTALL TRANSFER HIGH AND LOW SHIFT FORK SHAFT

a.
C291215

Install the transfer high and low shift fork shaft.


Hide 36349 17.INSTALL TRANSFER SELECT RETURN SPRING

a.
C291156

Install the transfer select return spring.


Hide 44186 18.INSTALL SOLENOID COVER

a.
C291155E01
2.353,0.509 1.928,0.07 1.928,0.07 1.679,0.07 false 1.481,0 1.647,0.170 0.166,0.170 10 *1 2.091,0.968 1.528,1.849 1.528,1.849 1.279,1.849 false 1.081,1.768 1.248,1.937 0.166,0.170 10 *2

Install the solenoid cover and No. 1 transfer output shaft spacer.

Text in Illustration
*1 No. 1 Transfer Output Shaft Spacer
*2 Solenoid Cover


Hide 36231J 19.INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

a.
C291154E01
1.803,0.692 2.151,0.202 2.151,0.202 2.865,0.202 false 2.916,0.116 3.086,0.286 0.170,0.170 10 *a

Install the rear transfer output shaft radial ball bearing.


b.

Using a screwdriver, install the transfer output shaft rear shaft snap ring.

Text in Illustration
*a Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 36292A 20.INSTALL TRANSFER DRIVEN SPROCKET BEARING (REAR)

a.
C291182E01
0.51,0.249 0.635,0.249 0.635,0.249 1.116,1.22 false 0.944,1.465 0.635,0.249 false 0.089,0.171 0.415,0.327 0.326,0.156 10 SST 2.349,0.635 2.474,0.635 2.474,0.635 2.642,1.332 false 1.928,0.558 2.254,0.714 0.326,0.156 10 SST

Using SST and a hammer, tap in a new transfer driven sprocket bearing (rear).

SST
09950-60010  (09951-00340, 09952-06010)
09950-60020  (09951-00730)
09950-70010  (09951-07150)

NOTICE:

The transfer driven sprocket bearing (rear) should be installed completely.



Hide 36102J 21.INSTALL TRANSFER COVER TYPE T OIL SEAL

a.
U152629E02
1.594,1.104 1.052,0.167 1.052,0.167 0.813,0.167 false 2.74,1.021 2.74,0.26 2.74,0.26 2.635,0.26 false 2.333,1.458 2.521,1.458 false 2.385,1.104 2.385,0.823 false 2.292,1.177 2.5,1.177 false 0.469,0.094 0.792,0.271 0.323,0.177 10 false SST 2.271,0.188 2.594,0.365 0.323,0.177 10 true SST 2.208,0.865 2.333,1.042 0.125,0.177 10 true A

Using SST and a hammer, tap in a new transfer cover type T oil seal.

SST
09950-70010  (09951-07100)
09950-60010  (09951-00190)

Drive in depth (A):

14.4 to 15.4 mm (0.567 to 0.606 in.)



Hide 44109C 22.INSTALL SOLENOID COIL SUB-ASSEMBLY

a.
C291151E01
1.567,0.904 1.404,1.432 1.404,1.432 0.403,1.432 false 0.171,1.325 0.351,1.505 0.180,0.180 10 *a

Install the solenoid coil sub-assembly with the 3 nuts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

Text in Illustration
*a Rear Transfer Case Hole

HINT:

Make sure that the solenoid coil sub-assembly terminal extends out from the rear transfer case hole.



b.

Connect the solenoid coil sub-assembly terminal.

i.
C301682

Attach the claw to connect the solenoid coil sub-assembly terminal.


ii.
C301683

Install the retainer to the coupler.



Hide 36112 23.INSTALL REAR TRANSFER CASE

a.
C291212E01
0.873,0.529 0.873,0.286 0.873,0.286 0.761,0.286 false 0.53,0.185 0.755,0.369 0.225,0.184 10 *a

Apply seal packing to the rear transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Text in Illustration
*a Seal Packing

NOTICE:

If the removed rear transfer case will be reused: After removing the rear transfer case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the contact surface of the rear transfer case, 2) clean off any remaining old seal packing from the contact surface of the rear transfer case, and 3) reapply seal packing to the rear transfer case.



b.
C291150

Using a 40 IP ''TORX PLUS'' socket wrench or T40 ''TORX'' socket wrench, install the 17 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 84222F 24.INSTALL TRANSFER INDICATOR SWITCH

Hide 36104A 25.INSTALL TRANSFER OUTPUT SHAFT TYPE T OIL SEAL

Hide 33309C 26.INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (REAR)

a.

Install the output shaft companion flange sub-assembly (rear) onto the rear transfer output shaft.


b.
C291217E02
1.24,0.344 1.427,0.094 1.427,0.094 1.604,0.094 false 1.656,0.01 2,0.177 0.344,0.167 10 false SST 0.51,0.354 0.688,0.531 0.177,0.177 10 false *a 0.823,1.813 1,1.969 0.177,0.156 10 true *b

Using SST, hold the output shaft companion flange sub-assembly (rear).

SST
09330-00021  


c.

Using a 30 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

Torque:
127 N*m (1295 kgf*cm, 94 ft.*lbf)

Text in Illustration
*a Hold
*b Turn


d.
F050151E09
1.76,0.51 1.823,0.354 1.823,0.354 2,0.354 false 1.938,1.354 2,1.188 2,1.188 2.177,1.188 false 1.76,2.188 1.833,2.031 1.833,2.031 2.01,2.031 false 1.938,3.094 2,2.938 2,2.938 2.177,2.938 false 2.25,0.875 1.979,0.875 false 2.167,1.49 1.896,1.49 false 2.25,2.573 1.979,2.573 false 2.177,3.229 1.906,3.229 false 1.146,0.26 1.333,0.427 0.188,0.167 10 false *a 1.135,1.958 1.323,2.125 0.188,0.167 10 false *b 2.052,0.26 2.24,0.427 0.188,0.167 10 false *1 2.219,1.094 2.406,1.26 0.188,0.167 10 false *1 2.063,1.958 2.25,2.125 0.188,0.167 10 false *1 2.208,2.865 2.396,3.031 0.188,0.167 10 false *1 2.292,0.802 2.479,0.969 0.188,0.167 10 false *2 2.208,1.427 2.396,1.594 0.188,0.167 10 false *2 2.281,2.479 2.469,2.646 0.188,0.167 10 false *2 2.219,3.156 2.406,3.323 0.188,0.167 10 false *2

Using a chisel and hammer, stake the transfer output shaft nut.

Text in Illustration
*1 Transfer Output Shaft Nut
*2 Rear Transfer Output Shaft
*a Correct
*b Incorrect


Hide 36410J 27.INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

Hide 82715D 28.INSTALL WIRING HARNESS CLAMP BRACKET

a.
C291143

Install the wiring harness clamp bracket with the 2 bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


b.

Connect the connector and 3 clamps.


c.
C291200

Install the 3 wiring harness clamp brackets with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Install the wiring harness clamp bracket in the correct direction.



Hide 36179 29.INSTALL LOWER TRANSFER CASE PROTECTOR

a.

Install the lower transfer case protector with the 4 bolts.

Torque:
22 N*m (219 kgf*cm, 16 ft.*lbf)