Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234172 AUTOMATIC TRANSMISSION UNIT A

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

C155869

a.

Remove the nut, spring washer and control shaft lever RH.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
D027903

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 32921C 3.REMOVE OIL COOLER TUBE UNION

C158384

a.

Remove the 2 oil cooler tube unions.


b.

Remove the O-ring from each oil cooler tube union.


Hide 89413B 4.REMOVE SPEED SENSOR

C111258

a.

Remove the 2 bolts and 2 speed sensors.


b.

Remove the O-ring from each sensor.


Hide 35122 5.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C117463

a.

Remove the 2 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 35111 6.REMOVE AUTOMATIC TRANSMISSION HOUSING

C210201

a.

Remove the 10 bolts and transmission housing.


Hide 35015G 7.REMOVE REAR TRANSFER ADAPTER

U152370

a.

Remove the 8 bolts and transfer adapter.

HINT:

Use a brass bar and hammer to remove the transfer adapter.



b.

Using a screwdriver, remove the transfer adapter hole snap ring.


Hide 35015J 8.REMOVE TRANSFER CASE ADAPTER REAR OIL SEAL

C162766

a.

Using a screwdriver, pry out the oil seal.

NOTICE:

Be careful not to damage the transfer adapter.


HINT:

Wrap the tip of the screwdriver with tape.



Hide 35104 9.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

D027911

a.

Install the transmission case to an overhaul attachment.


Hide 35106 10.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Remove the drain plug and gasket.


b.

Remove the overflow plug and gasket.


c.
C210200

Remove the 20 bolts and oil pan.

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with any foreign matter in the bottom of the pan.



Hide 35106 11.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35330 12.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C209698

a.

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body.


c.

Remove the O-ring from the oil strainer.


Hide 82125J 13.REMOVE TRANSMISSION WIRE

C352742

a.

Remove the 2 bolts and 2 temperature sensor clamps.


b.

Disconnect the 2 ATF temperature sensors.


c.

Disconnect the 9 solenoid valve connectors.


d.

Detach the wire harness from the 2 clamps.


e.
D027912

Remove the bolt and pull out the transmission wire.


f.

Remove the O-ring from the transmission wire connector.


Hide 35410 14.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.

Remove the bolt, detent spring cover and detent spring.


b.
C351964

Remove the 19 bolts and valve body.


Hide 35251 15.REMOVE CHECK BALL BODY

C351965E01
1.885,0.385 2.146,0.385 false 1.854,0.802 2.115,0.802 false 2.177,0.302 3.302,0.479 1.125,0.177 10 false Check Ball Body 2.146,0.729 2.635,0.927 0.49,0.198 10 false Spring

a.

Remove the check ball body and spring.


Hide 35145C 16.REMOVE TRANSMISSION CASE GASKET

D027968

a.

Remove the 3 gaskets.


Hide 35159 17.REMOVE BRAKE DRUM GASKET

a.
D027969

Remove the 3 gaskets.


Hide 35425A 18.REMOVE C-2 ACCUMULATOR PISTON

D027915

a.

While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 35427K 19.REMOVE B-3 ACCUMULATOR PISTON

D027915

a.

While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 35426D 20.REMOVE C-3 ACCUMULATOR PISTON

D027916

a.

While applying compressed air to the oil hole, remove the C-3 accumulator piston and 2 springs.


b.

Remove the 2 O-rings from the piston.


Hide 35427T 21.REMOVE B-1 ACCUMULATOR VALVE

D027917

a.

Remove the B-1 accumulator valve and 2 springs.


Hide 35595 22.REMOVE PARKING LOCK PAWL BRACKET

D012708

a.

Remove the 3 bolts and bracket.


Hide 35501 23.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

D012709

a.

Remove the parking lock rod from the manual valve lever.


Hide 35556 24.REMOVE PARKING LOCK PAWL SHAFT

D028846

a.

Pull out the parking lock pawl shaft from the front side to remove it, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 35505 25.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918

a.

Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.


b.
D027919

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly drive out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the case, and remove the manual valve lever.


Hide 35506F 26.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C352744

a.

Using a screwdriver, pry out the 2 oil seals.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape.



Hide 27.REMOVE OIL PUMP ASSEMBLY

D027921

a.

Remove the 10 bolts.


b.
D027922E06
1.885,0.906 2.104,0.344 false 2.167,0.229 2.5,0.375 0.333,0.146 10 false SST

Using SST, remove the oil pump.

SST
09350-30020  (09350-07020)


c.
C161631

Remove the 2 thrust bearing races and O-ring from the oil pump.


Hide 28.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027923

a.

Remove the clutch drum and input shaft drum assembly from the transmission case.


b.
C161633

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 35780B 30.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

D027994

a.

Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 31.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161636

a.

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.


Hide 35049 32.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

C161637

a.

Using a screwdriver, remove the snap ring.


b.
C161638

Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.


Hide 35677C 33.REMOVE REAR CLUTCH DISC SET

D027999

a.

Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


b.
C162148

Remove the reverse clutch flange from the clutch drum.


Hide 35061 36.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C161641

a.

Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.


Hide 35064 38.REMOVE COAST CLUTCH HUB SUB-ASSEMBLY

C161642

a.

Remove the 2 thrust needle roller bearings, coast clutch hub together with the underdrive 1-way clutch and thrust bearing race from the clutch drum.


Hide 34360B 40.REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY

C161643

a.

Remove the underdrive 1-way clutch from the coast clutch hub.


b.

Remove the No. 2 clutch hub thrust washer from the coast clutch hub.


Hide 35633B 41.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET

C161644

a.

Using a screwdriver, remove the hole snap ring.


b.
C210190

Remove the flange, 5 discs and 5 plates from the input shaft.


Hide 35633B 42.INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

Hide 35685 43.REMOVE COAST CLUTCH DISC SET

C161646

a.

Using a screwdriver, remove the hole snap ring.


b.
C210189

Remove the flange, 3 discs and 3 plates from the input shaft.


Hide 35701 45.REMOVE INPUT SHAFT ASSEMBLY

C161648

a.

Remove the input shaft from the clutch drum.


Hide 35712A 46.REMOVE INPUT SHAFT OIL SEAL RING

C161649

a.

Remove the 4 oil seal rings from the input shaft.


Hide 35621Y 47.REMOVE COAST CLUTCH PISTON

C161650E01
2.76,0.626 3.084,0.812 0.324,0.186 10 SST 2.137,0.648 2.715,0.708 2.715,0.708 1.633,0.943 false

a.

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C161651

Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.


d.
C161652

Remove the O-ring from the No. 1 clutch balancer.


e.
C161653

Hold the coast clutch piston by hand and apply compressed air to the input shaft to remove the coast clutch piston.


Hide 35603A 48.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35612B 49.REMOVE FORWARD CLUTCH PISTON

C161654

a.

Hold the forward clutch piston by hand and apply compressed air to the input shaft to remove the forward clutch piston.


b.
C162744

Remove the O-ring from the input shaft.


Hide 35667A 50.REMOVE DIRECT CLUTCH DISC SET

C159654

a.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.


b.
C162138

Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.


Hide 35668 52.REMOVE NO. 3 CLUTCH BALANCER

a.
D028509E09
1.708,0.885 2.479,0.573 2.479,0.573 2.26,0.927 true 2.552,0.448 2.896,0.646 0.344,0.198 10 false SST

Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

SST
09387-00070  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the No. 3 clutch balancer.


d.
C161657

Remove the reverse clutch return spring and O-ring from the reverse clutch piston sub-assembly.


Hide 35047 53.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35048 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

C161700

a.

Remove the reverse clutch piston from the clutch drum.


b.
C161702

Remove the O-ring from the reverse clutch piston.


c.
D028513

Remove the O-ring from the clutch drum.


Hide 35606A 55.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028514E11
1.406,1.375 0.521,1.396 0.521,1.396 1.208,0.604 true 0.229,1.333 0.573,1.531 0.344,0.198 10 false SST

a.

Place SST on the direct clutch piston, and compress the return spring with a press.

SST
09320-89010  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
D028515

Using 2 screwdrivers, remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.


d.
D028517

Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.


e.

Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.


f.
D028816

Remove the 2 O-rings from the direct clutch piston.


Hide 35604 56.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35679C 57.REMOVE NO. 3 BRAKE SNAP RING

D027925

a.

Using a screwdriver, remove the No. 3 brake snap ring from the case.


Hide 58.REMOVE NO. 3 BRAKE DISC SET

D027926

a.

Remove the flange, 4 discs, 4 plates and cushion plate from the case.


Hide 35624J 60.REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

D027927E16
1.406,0.292 0.698,0.292 true 0.354,0.208 0.667,0.406 0.313,0.198 10 true SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 35790 61.REMOVE 1-WAY CLUTCH ASSEMBLY

D027928

a.

Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.


Hide 35664 62.REMOVE NO. 3 BRAKE CYLINDER

D027929

a.

Remove the No. 3 brake cylinder from the case.


Hide 35624 63.REMOVE NO. 3 BRAKE PISTON

D028817E10
2.604,0.313 2.865,0.146 false 2.885,0.052 3.25,0.229 0.365,0.177 10 false SST

a.

Using SST and a press, compress the return spring and remove the snap ring.

SST
09351-40010  


b.
D028545

Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the No. 3 brake piston.


c.
D028546

Remove the 2 O-rings from the No. 3 brake piston.


Hide 35046 64.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35720 65.REMOVE FRONT PLANETARY GEAR ASSEMBLY

D027930

a.

Remove the 1-way clutch inner race and front planetary gear assembly from the case.


b.
D027931

Remove the thrust bearing race, thrust needle roller bearing and No. 2 planetary carrier thrust washer from the front planetary gear assembly.


Hide 68.REMOVE FRONT PLANETARY RING GEAR

D027932

a.

Remove the front planetary ring gear and thrust needle roller bearing from the transmission case.


Hide 35763 69.REMOVE CENTER PLANETARY RING GEAR

D028540

a.

Using a screwdriver, remove the snap ring.


b.
D028541

Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.


Hide 35681A 70.REMOVE NO. 1 BRAKE DISC SET

C162132

a.

Remove the flange, 4 discs and 4 plates from the case.


Hide 35608K 72.REMOVE NO. 1 BRAKE PISTON RETURN SPRING SNAP RING

D027934

a.

Using a screwdriver, remove the No. 1 brake piston return spring snap ring from the case.


Hide 35608J 73.REMOVE NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935

a.

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the case.


Hide 35608J 74.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621V 75.REMOVE NO. 1 BRAKE PISTON

D027936

a.

Hold the No. 1 brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35682A 76.REMOVE NO. 2 BRAKE DISC SET

D027937

a.

Using a screwdriver, remove the snap ring from the case.


b.
C161726

Remove the flange, 4 discs, 4 plates and brake piston return spring from the case.


Hide 35045 78.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35622G 79.REMOVE NO. 2 BRAKE PISTON

D027939

a.

Hold the No. 2 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston and No. 2 brake cylinder.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 2 brake piston.


Hide 35750 80.REMOVE CENTER PLANETARY GEAR ASSEMBLY

D027940

a.

Remove the thrust bearing race, center planetary gear and planetary sun gear from the case.


Hide 35713 82.REMOVE INTERMEDIATE SHAFT

D027941

a.

Using a screwdriver, remove the snap ring from the case.


b.
D027942

Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.


Hide 35770C 84.REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

a.
D027964

Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.


Hide 35077D 85.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965

a.

Remove the planetary ring gear flange together with the rear planetary ring gear, thrust bearing race, thrust needle roller bearing and thrust bearing race from the intermediate shaft.


b.
C161734

Using a screwdriver, remove the snap ring.


c.

Remove the rear planetary ring gear flange from the rear planetary ring gear.


Hide 35077D 86.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

Hide 35639B 88.REMOVE BRAKE PLATE STOPPER SPRING

D027943

Hide 89.REMOVE NO. 4 BRAKE DISC SET

C352746

a.

Remove the 2 flanges, 8 discs and 7 plates from the case.


Hide 35760 91.REMOVE REAR PLANETARY GEAR ASSEMBLY

D027945

a.

Remove the rear planetary gear assembly from the case.


b.
U116382

Remove the thrust needle roller bearing from the rear planetary gear.


c.
U116383

Remove the thrust bearing race from the case.


Hide 35068 93.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028083E06
2.406,1.01 2.323,0.188 2.323,0.188 2.438,0.188 true 1.458,0.75 1.406,0.26 1.406,0.26 1.302,0.26 true 2.5,0.115 3.229,0.49 0.729,0.375 10 true Snap Ring 1,0.177 1.375,0.344 0.375,0.167 10 false SST

a.

Place SST on the spring retainer and compress the brake return spring.

SST
09350-30020  (09350-07050)


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


Hide 35068 94.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35623H 95.REMOVE 1ST AND REVERSE BRAKE PISTON

D027948

a.

Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the O-ring from the 1st and reverse brake piston.


Hide 35626 96.REMOVE BRAKE REACTION SLEEVE

D028079E08
1.5,0.427 1.094,0.427 false 0.708,0.313 1.208,0.552 0.5,0.24 10 false SST

a.

Using SST, remove the reaction sleeve.

SST
09350-30020  (09350-07080)


b.

Remove the 2 O-rings from the reaction sleeve.


Hide 35629A 97.REMOVE NO. 4 BRAKE PISTON

D001240E06
1.26,0.313 1.563,0.542 false 0.917,0.177 1.313,0.385 0.396,0.208 10 false SST

a.

Using SST, remove the brake piston.

SST
09350-30020  (09350-07090)


b.

Remove the 2 O-rings from the brake piston.