Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234172 AUTOMATIC TRANSMISSION UNIT A

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

a.

Check the bearing positions.

U115892E01
1.163,0.562 1.322,0.755 0.160,0.193 10 A 4.478,1.395 4.638,1.588 0.160,0.193 10 C 5.591,2.6 5.751,2.793 0.160,0.193 10 D 5.819,4.105 5.979,4.298 0.160,0.193 10 F 4.07,4.532 4.230,4.725 0.160,0.193 10 G 1.214,6.782 1.374,6.975 0.160,0.193 10 H 3.755,6.122 3.915,6.315 0.160,0.193 10 I 6.014,0.921 6.173,1.114 0.160,0.193 10 E 1.596,2.103 1.756,2.296 0.160,0.193 10 B

Bearing Diameter:
Mark Front Race Diameter Inside/Outside Thrust Bearing Diameter Inside/Outside Rear Race Diameter Inside/Outside
A 74.26 to 74.56 mm (2.92 to 2.94 in.)/87.39 to 87.74 mm (3.44 to 3.45 in.) 71.96 to 72.26 mm (2.83 to 2.84 in.)/85.25 to 85.60 mm (3.36 to 3.37 in.) -
B 37.0 to 37.3 mm (1.46 to 1.47 in.)/52.1 to 52.3 mm (2.05 to 2.06 in.) 34.65 to 34.85 mm (81.36 to 1.37 in.)/51.56 to 51.86 mm (2.03 to 2.04 in.) -
C - 21.35 to 21.60 mm (0.841 to 0.850 in.)/40.72 to 40.92 mm (1.60 to 1.61 in.) 22.65 to 22.90 mm (0.892 to 0.902 in.)/44.50 to 44.75 mm (1.75 to 1.76 in.)
D - 35.65 to 35.9 mm (1.40 to 1.41 in.)/56.3 to 56.55 mm (2.22 to 2.23 in.) -
E - 42.55 to 42.80 mm (1.68 to 1.69 in.)/60.84 to 61.14 mm (2.40 to 2.41 in.) -
F 38.0 to 38.2 mm (1.49 to 1.50 in.)/56.50 to 57.0 mm (2.22 to 2.24 in.) 43.4 to 43.6 mm (1.71 to 1.72 in.)/58.0 to 58.25 mm (2.28 to 2.29 in.) -
G - 55.76 to 55.79 mm (2.19 to 2.20 in.)/76.1 to 76.35 mm (3.00 to 3.01 in.) 53.75 to 54.0 mm (2.12 to 2.13 in.)/73.7 to 74.0 mm (2.90 to 2.91 in.)
H 33.18 to 33.53 mm (1.31 to 1.32 in.)/48.8 to 49.0 mm (1.89 to 1.93 in.) 32.15 to 32.31 mm (1.26 to 1.27 in.)/48.97 to 49.77 mm (1.93 to 1.96 in.) 32.15 to 32.4 mm (1.27 to 1.28 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
I - 43.60 to 43.85 mm (1.72 to 1.73 in.)/62.95 to 63.20 mm (2.48 to 2.49 in.) 47.15 to 47.40 mm (81.86 to 1.87 in.)/67.07 to 67.40 mm (2.64 to 2.65 in.)



Hide 35629A 2.ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE

D028795E15
1.635,1.365 2.01,1.781 2.01,1.781 0.99,1.313 true 2.177,0.896 2.417,1.677 2.417,1.677 2.729,0.76 true 2.073,1.729 2.896,1.958 0.823,0.229 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.


b.

Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.


c.

Install the No. 4 brake piston to the reaction sleeve.


Hide 35626 3.INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE

D028080

a.

Install the No. 4 brake piston with brake reaction sleeve to the transmission case

NOTICE:
·

Do not damage the O-rings.

·

Make sure the No. 4 brake piston is underneath the brake reaction sleeve.




Hide 35623H 4.INSTALL 1ST AND REVERSE BRAKE PISTON

D028081

a.

Coat a new O-ring with ATF.


b.

Install the O-ring to the 1st and reverse brake piston.


c.

With the spring seat of the piston facing upwards (the front side), install the piston to the transmission case.

NOTICE:

Be careful not to damage the O-ring.



Hide 35068 5.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028549

a.

Place the brake return spring onto the 1st and reverse brake piston.


b.
D028082E03
1.563,0.792 1.563,0.24 1.563,0.24 1.667,0.24 false 1.063,0.292 1.135,0.292 1.135,0.292 1.01,0.958 false 1.688,0.156 2.01,0.323 0.323,0.167 10 false SST 0.365,0.198 1.073,0.385 0.708,0.188 10 false Snap Ring

Place SST on a new spring retainer, and compress the return spring.

SST
09350-30020  (09350-07050)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



d.
D027966

Make sure the No. 4 brake piston moves smoothly when applying and releasing compressed air into and from the transmission case.


Hide 35760 6.INSTALL REAR PLANETARY GEAR ASSEMBLY

U116383

a.

Install the thrust bearing race.

Bearing Race Diameter:
Item Inside Outside
Race I 47.15 to 47.40 mm (81.86 to 1.87 in.) 67.07 to 67.40 mm (2.64 to 2.65 in.)



b.
U116382

Install the thrust needle roller bearing to the rear planetary gear.

Bearing Diameter:
Item Inside Outside
Bearing I 43.60 to 43.85 mm (1.72 to 1.73 in.) 62.95 to 63.20 mm (2.48 to 2.49 in.)



c.
D027945

Install the rear planetary gear assembly.


Hide 35689 7.SELECT NO. 4 BRAKE FLANGE

a.
C352752E01
1.26,1.01 1.417,1.208 0.156,0.198 10 false A

Using a vernier caliper, measure distance A (from the top surface of the 1st and reverse brake piston to the step in the transmission case) in the illustration.

NOTICE:

The 1st and reverse brake piston must be installed securely to the end face of the transmission case.


HINT:

Distance A = 36.35 to 37.09 mm (1.43 to 1.46 in.)



b.
C210211E04
2.271,0.219 2.802,0.146 false 2.552,0.771 2.781,0.74 false 2.458,1.479 2.76,1.438 false 0.052,1.302 1.104,1.49 1.052,0.188 10 false Selected Flange 1.271,1.031 1.417,1.208 0.146,0.177 10 false H 1.417,0.74 1.552,0.896 0.135,0.156 10 false B 2.854,0.063 3.177,0.25 0.323,0.188 10 false Disc 2.844,0.646 3.25,0.844 0.406,0.198 10 false Plate 2.792,1.333 3.281,1.531 0.49,0.198 10 false Flange

Assemble the No. 4 brake flange, 8 No. 4 brake discs and 7 No. 4 brake plates, and using a vernier caliper, measure distance B in the illustration at both ends across the diameter, and calculate the average.

HINT:

Distance B = 33.94 to 35.04 mm (1.34 to 1.38 in.)



c.

Select a No. 4 brake flange so that the value of measured distance A minus distance B minus thickness H is 1.35 to 1.65 mm (0.0531 to 0.0650 in.).

Thickness H:
No. Thickness
0 0 mm (0 in.)
2 0.15 to 0.25 mm (0.00590 to 0.00984 in.)
4 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
6 0.55 to 0.65 mm (0.0217 to 0.0256 in.)
8 0.75 to 0.85 mm (0.0295 to 0.0335 in.)
10 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
12 1.15 to 1.25 mm (0.0453 to 0.0492 in.)
14 1.35 to 1.45 mm (0.0531 to 0.0571 in.)



Hide 35684 8.INSTALL NO. 4 BRAKE DISC

U152678E02
0.271,4.031 0.146,4.042 false 3.417,0 3.302,0 false 3.417,0 3.323,0 false 3.417,0 3.292,0 false 0.302,1.823 0.167,1.823 false 3.417,0 3.302,0 false 3.417,0 3.292,0 false 3.417,0 3.313,0 false 3.417,0 3.323,0 false 0.323,2.063 0.188,2.063 false 0.313,1.615 0.146,1.615 false 0.281,1.417 0.146,1.417 false 0.313,1.198 0.167,1.198 false 0.271,0.979 0.177,0.979 false 0.323,0.74 0.177,0.74 false 0.125,0.51 0.271,0.51 false 0.302,3.781 0.146,3.781 false 0.281,3.573 0.156,3.573 false 0.302,3.333 0.146,3.333 false 0.302,2.906 0.177,2.906 false 0.302,2.688 0.177,2.688 false 0.302,2.49 0.167,2.49 false 0.292,2.292 0.156,2.292 false 0.031,3.969 0.177,4.177 0.146,0.208 10 false F 0.031,2.406 0.177,2.615 0.146,0.208 10 false D 0.031,1.979 0.177,2.188 0.146,0.208 10 false D 0.031,1.115 0.177,1.323 0.146,0.208 10 false D 0.01,3.698 0.156,3.906 0.146,0.208 10 false D 0.021,3.25 0.167,3.469 0.146,0.219 10 false D 0.021,2.823 0.167,3.031 0.146,0.208 10 false D 0.031,1.542 0.177,1.75 0.146,0.208 10 false D 0.031,0.656 0.177,0.865 0.146,0.208 10 false D 0.031,1.333 0.177,1.542 0.146,0.208 10 false P 0.031,3.052 0.177,3.26 0.146,0.208 10 false P 0.031,2.615 0.177,2.823 0.146,0.208 10 false P 0.042,2.208 0.188,2.417 0.146,0.208 10 false P 0.052,1.76 0.198,1.969 0.146,0.208 10 false P 0.042,0.906 0.188,1.115 0.146,0.208 10 false P 0.021,3.49 0.167,3.698 0.146,0.208 10 false P 0.031,0.417 0.177,0.625 0.146,0.208 10 false F

a.

Install the flange, 8 discs, 7 plates and selected flange.

Install in order:

F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:

F = Flange

D = Disc

P = Plate



Hide 35639B 9.INSTALL BRAKE PLATE STOPPER SPRING

D027943

Hide 35077D 10.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

C161734

a.

Install the rear planetary ring gear flange to the rear planetary ring gear.


b.

Using a screwdriver, install the snap ring.


c.
D027965

Install the thrust bearing race, thrust needle roller bearing, thrust bearing race and planetary ring gear flange together with the rear planetary ring gear to the intermediate shaft.

Bearing and Race Diameter:
Item Inside Outside
Race H (Fr) 33.18 to 33.53 mm (1.31 to 1.32 in.) 48.8 to 49.0 mm (1.89 to 1.93 in.)
Bearing H 32.15 to 32.31 mm (1.26 to 1.27 in.) 48.97 to 49.77 mm (1.93 to 1.96 in.)
Race H (Rr) 32.15 to 32.4 mm (1.27 to 1.28 in.) 48.7 to 49.0 mm (1.92 to 1.93 in.)



Hide 35770C 11.INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

D027964

a.

Install the 1-way clutch and 1-way clutch inner race to the intermediate shaft.


Hide 35713 12.INSTALL INTERMEDIATE SHAFT

D027942

a.

Install the intermediate shaft with No. 3 1-way clutch assembly to the case.


b.
D027927E16
1.406,0.292 0.698,0.292 true 0.354,0.208 0.667,0.406 0.313,0.198 10 true SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35750 13.INSTALL CENTER PLANETARY GEAR ASSEMBLY

D027940

a.

Install the planetary sun gear and center planetary gear to the case.


b.

Coat the thrust bearing race with petroleum jelly, and install it to the center planetary gear.

Race Diameter:
Item Inside Outside
Race G 53.75 to 54.0 mm (2.12 to 2.13 in.) 73.7 to 74.0 mm (2.90 to 2.91 in.)



Hide 35622G 14.INSTALL NO. 2 BRAKE PISTON

D028797E17
1.073,0.635 1.01,0.125 true 0.708,1.479 1.01,0.125 1.01,0.125 1.146,0.125 true 1.208,0.042 2.083,0.396 0.875,0.354 10 true New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the brake piston.


b.

Press the brake piston into the brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



c.

Install the No. 2 brake cylinder with No. 2 brake piston to the case.

HINT:

Install the No. 2 brake cylinder so that the projection faces the upside of the transmission case.



d.
D031529

Check that the oil pressure apply hole of the No. 2 brake cylinder aligns with the oil pressure apply hole of the transmission case.


Hide 35678B 15.SELECT NO. 2 BRAKE FLANGE

a.

Install the No. 2 brake piston return spring and flange to the No. 2 brake piston.


b.
D028818E14
1.844,1.146 2.823,0.542 2.823,0.542 2.083,0.542 true 2.896,0.458 3.333,0.74 0.438,0.281 10 true SST

Place SST on the brake flange and compress the brake return spring.

SST
09351-40010  (09351-04010, 09351-04020, 09351-04040, 09351-04050)


c.

Using a screwdriver, install the snap ring to the transmission case.


d.
C210212E05
2.135,1.698 1.292,2.063 1.292,2.063 1.177,2.063 true 0.219,1.969 1.135,2.542 0.917,0.573 10 true Return Spring Retainer 0.906,0.969 1.073,1.135 0.167,0.167 10 false A

Measure distance A (from the top surface of the snap ring to the surface of the brake piston return spring retainer) in the illustration.

HINT:

Standard distance A: 20.94 to 22.12 mm (0.824 to 0.871 in.)



e.

Remove the snap ring, flange and No. 2 brake piston return spring.


f.
C210213E04
2.594,1.354 2.75,1.354 false 2.094,0.99 2.604,0.99 false 2.073,0.76 2.75,0.76 false 2,0.198 1.917,0.198 1.917,0.198 1.729,0.604 false 0.719,0.958 0.854,1.146 0.135,0.188 10 false B 2.771,1.26 3.271,1.5 0.5,0.24 10 false Flange 2.073,0.125 2.594,0.323 0.521,0.198 10 false Flange 2.677,0.917 3.073,1.083 0.396,0.167 10 false Plate 2.792,0.677 3.125,0.854 0.333,0.177 10 false Disc

Assemble the flange, 4 discs, 3 plates and flange (thickness: 1.95 to 2.05 mm (0.0768 to 0.0807 in.)) as shown in the illustration, and using a vernier caliper, measure distance B in the illustration at both ends across the diameter, and calculate the average.

HINT:

Standard distance B: 18.52 to 19.15 mm (0.729 to 0.754 in.)



g.

Select a No. 2 brake flange so that the value of measured distance A minus distance B is 0.6 to 0.9 mm (0.0236 to 0.0354 in.).

Flange Thickness:
No. Thickness
0 0 1.95 to 2.05 mm (0.0768 to 0.0807 in.)
1 2.05 to 2.15 mm (0.0807 to 0.0846 in.)
2 2.15 to 2.25 mm (0.0846 to 0.0886 in.)
3 2.25 to 2.35 mm (0.0886 to 0.0925 in.)
4 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
5 2.45 to 2.55 mm (0.0965 to 0.100 in.)
6 2.55 to 2.65 mm (0.100 to 0.104 in.)
7 2.65 to 2.75 mm (0.104 to 0.108 in.)



Hide 35682A 16.INSTALL NO. 2 BRAKE DISC SET

C161726E08
0.604,0.292 0.542,0.292 false 0.667,0.563 0.542,0.563 false 0.667,0.823 0.542,0.823 false 0.667,1.073 0.542,1.073 false 0.667,1.313 0.542,1.313 false 1.354,0.698 1.292,0.698 false 1.354,0.938 1.292,0.938 false 1.354,1.188 1.292,1.188 false 1.354,1.406 1.292,1.406 false 1.365,1.323 1.531,1.5 0.167,0.177 10 true F 0.406,0.198 0.531,0.365 0.125,0.167 10 false F 0.406,0.469 0.531,0.635 0.125,0.167 10 false D 0.406,0.75 0.531,0.917 0.125,0.167 10 false D 0.406,0.979 0.531,1.146 0.125,0.167 10 false D 0.406,1.229 0.531,1.396 0.125,0.167 10 false D 1.354,0.615 1.479,0.781 0.125,0.167 10 false P 1.354,0.865 1.479,1.031 0.125,0.167 10 false P 1.354,1.104 1.479,1.271 0.125,0.167 10 true P

a.

Install the brake piston return spring.


b.

Install the 2 flanges, 4 discs, 3 plates.

Install in order:

F - D - P - D - P - D - P - D - F


HINT:

D = Disc

P = Plate

F = Flange



c.
D028818E14
1.844,1.146 2.823,0.542 2.823,0.542 2.083,0.542 true 2.896,0.458 3.333,0.74 0.438,0.281 10 true SST

Using SST and a press, compress the return spring and install the snap ring.

SST
09351-40010  (09351-04010, 09351-04030, 09351-04040, 09351-04050)


Hide 35621V 17.INSTALL NO. 1 BRAKE PISTON

U152680E02
1.427,0.698 1.292,0.125 false 1.49,0.01 2.344,0.427 0.854,0.417 10 true New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the brake piston.


b.

Press the brake piston into the brake cylinder with both hands to install it.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608J 18.INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935

a.

Install the No. 1 brake cylinder with No. 1 brake piston and the brake piston return spring to the transmission case.


b.
D031528

Check that the oil pressure apply hole of the No. 1 brake cylinder aligns with the oil pressure apply hole of the transmission case.


Hide 35608K 19.INSTALL NO. 1 BRAKE PISTON RETURN SPRING SNAP RING

D028819E09
1.604,1.365 0.438,1.271 0.438,1.271 1.604,0.885 true 0.125,1.208 0.531,1.448 0.406,0.24 10 false SST

a.

Using SST, compress the return spring and install the No. 1 brake piston return spring snap ring.

SST
09351-40010  (09351-04010, 09351-04030, 09351-04040, 09351-04050)


Hide 35676B 20.SELECT NO. 1 BRAKE FLANGE

C210214E04
1.938,3.198 2.01,2.875 2.01,2.875 2.063,2.875 false 2.135,3.885 2.563,3.885 false 2.094,3.813 2.583,3.625 false 1.25,0.875 1.406,1.063 0.156,0.188 10 false A 1.26,3.448 1.406,3.656 0.146,0.208 10 false B 2.615,3.792 3.052,3.979 0.438,0.188 10 false Plate 2.625,3.531 2.958,3.719 0.333,0.188 10 false Disc 2.125,2.792 2.615,2.979 0.49,0.188 10 false Flange

a.

Using a vernier caliper, measure distance A (from the step in the transmission case to the top surface of the No. 1 brake piston) in the illustration.

HINT:

Standard distance A: 19.74 to 20.22 mm (0.777 to 0.796 in.)



b.

Assemble the 4 plates, 4 discs and flange (thickness: 2.15 to 2.25 mm (0.0846 to 0.0886 in.)) as shown in the illustration, and using a vernier caliper, measure distance B in the illustration at both ends across the diameter, and calculate the average.

HINT:

Standard distance B: 18.93 to 19.39 mm (0.745 to 0.763 in.)



c.

Select a No. 1 brake flange so that the value of measured distance A minus distance B is 0.56 to 0.86 mm (0.0220 to 0.0339 in.).

Flange Thickness:
No. Thickness
0 1.95 to 2.05 mm (0.0768 to 0.0807 in.)
1 2.15 to 2.25 mm (0.0846 to 0.0886 in.)
2 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
3 2.55 to 2.65 mm (0.100 to 0.104 in.)



Hide 35681A 21.INSTALL NO. 1 BRAKE DISC

C162132E01
0.153,0.642 0.285,0.808 0.132,0.166 10 F 0.153,0.816 0.285,0.982 0.132,0.166 10 D 0.153,1.06 0.285,1.226 0.132,0.166 10 P 0.153,1.232 0.285,1.398 0.132,0.166 10 D 0.153,1.476 0.285,1.641 0.132,0.166 10 P 0.153,1.647 0.285,1.813 0.132,0.166 10 D 0.153,1.891 0.285,2.057 0.132,0.166 10 P 0.153,2.063 0.285,2.228 0.132,0.166 10 D 0.153,2.306 0.285,2.472 0.132,0.166 10 P 0.366,0.728 0.295,0.728 false 0.381,0.905 0.295,0.905 false 0.366,1.148 0.295,1.148 false 0.378,1.313 0.295,1.313 false 0.366,1.568 0.295,1.568 false 0.376,1.736 0.295,1.736 false 0.366,1.988 0.295,1.988 false 0.376,2.164 0.295,2.164 false 0.366,2.413 0.295,2.413 false

a.

Install the 4 plates, 4 discs and flange.

Install in order:

P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange



Hide 35763 22.INSTALL CENTER PLANETARY RING GEAR

D028541

a.

Install the center planetary ring gear and front planetary ring gear flange to the front planetary ring gear.


b.
D028540

Using a screwdriver, install the snap ring.


Hide 35743 23.INSTALL FRONT PLANETARY RING GEAR

D027932

a.

Install the thrust needle roller bearing and front planetary ring gear to the case.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing G 55.76 to 55.79 mm (2.19 to 2.20 in.) 76.1 to 76.35 mm (3.00 to 3.01 in.)



Hide 35720 24.INSTALL FRONT PLANETARY GEAR ASSEMBLY

D027931E24
0.833,0.26 1.042,0.26 false 0.833,0.948 1.042,0.948 false 1.104,0.885 1.646,1.198 0.542,0.313 10 true Bearing 1.104,0.188 1.49,0.438 0.385,0.25 10 true Race

a.

Install the thrust washer and thrust needle roller bearing.


b.

Coat the thrust bearing race with petroleum jelly, and install it to the front planetary ring gear.

Thrust Needle Roller Bearing and Race Diameter:
Item Inside Outside
Bearing F 43.4 to 43.6 mm (1.71 to 1.72 in.) 58.0 to 58.25 mm (2.28 to 2.29 in.)
Race F 38.0 to 38.2 mm (1.49 to 1.50 in.) 56.50 to 57.0 mm (2.22 to 2.24 in.)



c.
D027930

Install the front planetary gear assembly and 1-way clutch inner race to the case.


Hide 35624 25.INSTALL NO. 3 BRAKE PISTON

D028546E20
1.177,0.802 1.021,0.125 true 1.135,0.125 1.021,0.125 1.021,0.125 0.635,1.26 true 1.188,0.01 1.979,0.375 0.792,0.365 10 true New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the No. 3 brake piston.


b.

Press the No. 3 brake cylinder into the No. 3 brake piston with both hands to install it.

NOTICE:

Be careful not to damage the O-rings.



c.
D028817E11
2.604,0.313 2.865,0.146 false 2.885,0.052 3.25,0.229 0.365,0.177 10 false SST

Using SST and a press, compress the return spring and install the snap ring.

SST
09351-40010  

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35664 26.INSTALL NO. 3 BRAKE CYLINDER

D027929

a.

Install the No. 3 brake cylinder to the case.


Hide 35790 27.INSTALL 1-WAY CLUTCH ASSEMBLY

D027928

a.

Install the thrust washer and 1-way clutch to the case.


Hide 35624J 28.INSTALL NO. 3 BRAKE PISTON HOLE SNAP RING

D027927E16
1.406,0.292 0.698,0.292 true 0.354,0.208 0.667,0.406 0.313,0.198 10 true SST

a.

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 29.INSTALL NO. 3 BRAKE DISC

D027926E13
0.365,0.271 0.25,0.271 false 0.354,0.458 0.25,0.458 false 0.365,0.615 0.25,0.615 false 0.354,0.75 0.25,0.75 false 0.365,0.917 0.25,0.917 false 0.354,1.063 0.25,1.063 false 0.365,1.229 0.25,1.229 false 0.354,1.365 0.25,1.365 false 0.365,1.542 0.25,1.542 false 0.354,1.729 0.25,1.729 false 0.094,0.156 0.208,0.354 0.115,0.198 10 false F 0.094,0.354 0.229,0.552 0.135,0.198 10 false D 0.094,0.5 0.219,0.698 0.125,0.198 10 false P 0.094,0.656 0.229,0.854 0.135,0.198 10 false D 0.094,0.813 0.219,1.01 0.125,0.198 10 false P 0.094,0.969 0.229,1.167 0.135,0.198 10 false D 0.094,1.125 0.219,1.323 0.125,0.198 10 false P 0.094,1.271 0.229,1.469 0.135,0.198 10 false D 0.094,1.417 0.219,1.615 0.125,0.198 10 false P 0.094,1.594 0.229,1.792 0.135,0.198 10 false C

a.

Install the cushion plate, 4 plates, 4 discs and flange to the case.

Install in order:

C - P - D - P - D - P - D - P - D - F


HINT:

C = Cushion plate

P = Plate

D = Disc

F = Flange



Hide 35679C 30.INSTALL NO. 3 BRAKE SNAP RING

D027925

a.

Using a screwdriver, install the snap ring.


Hide 35606A 31.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028816E10
2.073,1.333 2.302,1.74 2.302,1.74 2.552,1.302 false 1.896,1.771 2.698,1.969 0.802,0.198 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them in the direct clutch piston.


b.
D028517

Install the direct clutch return spring and No. 2 clutch balancer to the direct clutch piston sub-assembly.


c.

Press the direct clutch piston with clutch return spring and clutch balancer into the reverse clutch piston with both hands to install them.

NOTICE:

Be careful not to damage the O-ring.



d.
C352753E01
1.74,1.198 2.344,2.083 2.344,2.083 2.219,1.313 true 2.271,2.125 2.729,2.323 0.458,0.198 10 false SST

Place SST on the direct clutch balancer, and compress the return spring with a press.

SST
09320-89010  

SST
09350-30020  

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



e.
D028536E17
1.219,1.01 1.74,1.427 1.74,1.427 2.219,1 true 1.521,1.448 2.073,1.844 0.552,0.396 10 true Stopper

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



f.

Position the end gap of the snap ring in the balancer as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35048 32.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

D028513E09
1.188,1.792 1.365,1.854 false 1.385,1.781 2.188,1.99 0.802,0.208 10 false New O-Ring

a.

Coat a new O-ring with ATF, and install it to the clutch drum.


b.
D028512E09
2.219,0.344 1.75,0.208 false 0.958,0.104 1.771,0.333 0.813,0.229 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the reverse clutch piston.


c.
D028511

Press the clutch drum into the reverse clutch piston with both hands.

NOTICE:

Be careful not to damage the O-rings.



Hide 35688 33.INSTALL NO. 3 CLUTCH BALANCER

D028510E15
1.313,0.677 1.052,0.448 false 0.302,0.323 1.135,0.531 0.833,0.208 10 false New O-Ring

a.

Coat a new O-ring with ATF, and install it to the reverse clutch piston.


b.

Install the reverse clutch return spring and balancer to the reverse clutch piston.


c.
D028509E10
1.708,0.885 2.479,0.573 2.479,0.573 2.26,0.927 true 2.531,0.479 2.875,0.677 0.344,0.198 10 false SST

Place SST on the clutch balancer, and compress the return spring with a press.

SST
09387-00070  

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



d.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



e.
D028534E06
0.719,0.5 0.75,1.031 0.75,1.031 0.865,1.031 true 0.906,0.948 1.313,1.125 0.406,0.177 10 false Gap

Position the end gap of the snap ring in the piston as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35667A 34.INSTALL DIRECT CLUTCH DISC

C162138E01
1.02,0.346 1.148,0.517 0.128,0.171 10 F 1.02,0.765 1.148,0.935 0.128,0.171 10 P 1.02,0.584 1.148,0.755 0.128,0.171 10 D 1.02,1.131 1.148,1.302 0.128,0.171 10 P 1.02,0.95 1.148,1.121 0.128,0.171 10 D 1.02,1.5 1.148,1.671 0.128,0.171 10 P 1.02,1.309 1.148,1.480 0.128,0.171 10 D 1.02,1.88 1.148,2.050 0.128,0.171 10 P 1.02,1.678 1.148,1.849 0.128,0.171 10 D 1.02,2.249 1.148,2.419 0.128,0.171 10 P 1.02,2.058 1.148,2.228 0.128,0.171 10 D 1.28,0.435 1.16,0.435 false 1.302,0.66 1.171,0.66 false 1.306,0.845 1.171,0.845 false 1.305,1.03 1.171,1.03 false 1.307,1.226 1.171,1.226 false 1.305,1.396 1.171,1.396 false 1.306,1.587 1.171,1.587 false 1.306,1.759 1.171,1.759 false 1.307,1.963 1.171,1.963 false 1.307,2.139 1.171,2.139 false 1.307,2.33 1.171,2.33 false 1.02,2.601 1.148,2.772 0.128,0.171 10 P 1.02,2.41 1.148,2.581 0.128,0.171 10 D 1.307,2.491 1.171,2.491 false 1.307,2.683 1.171,2.683 false

a.

Install the 6 plates, 6 discs and direct clutch flange to the clutch drum.

Install in order:

P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.
C162740

Using a screwdriver, install the snap ring to the clutch drum.


c.

Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) into the oil hole as shown in the illustration.

U152438E02
1.604,0.833 2.26,0.833 false 1.604,0.865 2.26,0.865 false 1.833,0.406 1.833,1.25 false 6.073,1.49 6.25,2.958 6.25,2.958 6.135,2.958 true 2.344,0.75 3.198,0.948 0.854,0.198 10 false Distance (A) 5.594,2.885 6.177,3.094 0.583,0.208 10 false Oil Hole

Standard moving distance (A):

0.60 to 0.90 mm (0.0236 to 0.0354 in.)


If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
2 2.95 to 3.05 mm (0.116 to 0.120 in.)
3 3.05 to 3.15 mm (0.120 to 0.124 in.)
4 3.15 to 3.25 mm (0.124 to 0.128 in.)
5 3.25 to 3.35 mm (0.128 to 0.132 in.)
6 3.35 to 3.45 mm (0.132 to 0.136 in.)
7 3.45 to 3.55 mm (0.136 to 0.140 in.)
8 3.55 to 3.65 mm (0.140 to 0.144 in.)
9 3.65 to 3.75 mm (0.144 to 0.148 in.)
A 3.75 to 3.85 mm (0.148 to 0.152 in.)



d.

Temporarily remove the snap ring, replace the flange with the selected flange and reinstall the snap ring.


Hide 35649 35.SELECT REVERSE CLUTCH FLANGE

C162741

a.

Using a screwdriver, install the snap ring to the clutch drum.

NOTICE:

Make sure to install the direct clutch and reverse clutch snap rings so that their openings face opposite directions.



b.
C175544E02
2.195,1.092 2.105,1.092 false 2.195,1.453 2.105,1.453 false 2.195,1.813 2.105,1.813 false 2.195,2.173 2.105,2.173 false 2.195,2.534 2.105,2.534 false 1.174,1.276 1.084,1.276 false 1.174,0.915 1.084,0.915 false 1.174,1.636 1.084,1.636 false 1.174,1.997 1.084,1.997 false 1.174,2.357 1.084,2.357 false 1.174,2.801 1.084,2.801 false 2.23,1.005 2.368,1.175 0.138,0.170 10 D 2.195,0.742 2.138,0.742 false 2.234,0.655 2.371,0.826 0.138,0.170 10 C 2.23,1.365 2.368,1.536 0.138,0.170 10 D 2.23,1.726 2.368,1.896 0.138,0.170 10 D 2.23,2.086 2.368,2.256 0.138,0.170 10 D 2.23,2.446 2.368,2.617 0.138,0.170 10 D 0.94,0.835 1.069,1.012 0.129,0.177 10 F 0.94,1.195 1.078,1.375 0.138,0.180 10 P 0.94,1.554 1.078,1.735 0.138,0.180 10 P 0.94,1.914 1.078,2.094 0.138,0.180 10 P 0.94,2.274 1.078,2.454 0.138,0.180 10 P 0.94,2.734 1.068,2.892 0.128,0.158 10 F

Install the 2 flanges, 5 discs, 4 plates, cushion plate and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - P - D - F - C


HINT:

F = Flange

D = Disc

P = Plate

C = Cushion plate



c.
C162743

Using a screwdriver, install the hole snap ring.


d.

Using a dial indicator, measure the moving distance (A minus B) of the top surface of the reverse clutch piston (A) and cushion plate at both ends across the diameter (B) while applying compressed air (392 kPa, 4.0 kgf/ cm2, 57 psi) into the oil hole as shown in the illustration. Then choose a flange of an appropriate thickness from the table so that the measured value is within the standard range.

U152439E02
0.469,0.354 1.073,0.354 false 0.469,0.396 1.073,0.396 false 0.917,0.198 0.917,0.552 false 4.75,0.854 5.125,0.854 false 4.781,0.875 5.125,0.875 false 4.958,0.698 4.958,1.031 false 1.771,1.031 2.448,1.927 2.448,1.927 2.521,1.927 true 5.563,1.021 6.219,1.927 6.219,1.927 6.292,1.927 true 1.042,0.177 1.823,0.469 0.781,0.292 10 true Distance (A) 4.802,0.385 5.656,0.688 0.854,0.302 10 true Distance (B) 2.552,1.854 3.135,2.073 0.583,0.219 10 false Oil Hole 6.333,1.854 6.917,2.073 0.583,0.219 10 false Oil Hole

Standard moving distance (A minus B):

0.50 to 0.80 mm (0.0197 to 0.0315 in.)


Flange Thickness:
Mark Thickness
0 2.75 to 2.85 mm (0.108 to 0.112 in.)
1 2.85 to 2.95 mm (0.112 to 0.116 in.)
2 2.95 to 3.05 mm (0.116 to 0.120 in.)
3 3.05 to 3.15 mm (0.120 to 0.124 in.)
4 3.15 to 3.25 mm (0.124 to 0.128 in.)
5 3.25 to 3.35 mm (0.128 to 0.132 in.)
6 3.35 to 3.45 mm (0.132 to 0.136 in.)
7 3.45 to 3.55 mm (0.136 to 0.140 in.)
8 3.55 to 3.65 mm (0.140 to 0.144 in.)
9 3.65 to 3.75 mm (0.144 to 0.148 in.)
A 3.75 to 3.85 mm (0.148 to 0.152 in.)



e.
D029843

Remove the snap ring, reverse clutch reaction sleeve and rear clutch disc set from the clutch drum.


Hide 35602A 36.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY AND COAST CLUTCH PISTON

C162744E04
2.542,0.813 2.385,0.167 2.385,0.167 2.292,0.167 false 1.51,0.073 2.292,0.292 0.781,0.219 10 false New O-Ring

a.

Coat a new O-ring with ATF, and install it to the input shaft.


b.
C162745

Install the forward clutch piston and coast clutch piston to the input shaft.


c.
C161652E01
1.922,1.687 2.740,1.895 0.819,0.208 10 New O-Ring 1.521,1.603 1.89,1.754 false

Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.


d.

Install the forward clutch return spring and No. 1 clutch balancer to the input shaft.

NOTICE:

Be careful not to damage the O-rings.



e.
C161650E01
2.76,0.626 3.084,0.812 0.324,0.186 10 SST 2.137,0.648 2.715,0.708 2.715,0.708 1.633,0.943 false

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

SST
09350-30020  (09350-07040)

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



f.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



g.
C162759E05
0.698,1.26 1.563,1.625 0.865,0.365 10 true INCORRECT 0.698,0.125 1.458,0.458 0.76,0.333 10 true CORRECT

Position the end gap of the snap ring in the balancer as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35685 37.INSTALL COAST CLUTCH DISC SET

C109355E03
1.313,1.214 1.434,1.214 1.434,1.214 1.434,0.372 false 1.313,0.703 1.434,0.703 false 1.313,0.959 1.434,0.959 false 0.394,0.517 0.252,0.517 false 0.432,0.815 0.252,0.815 false 0.432,1.071 0.252,1.071 false 0.432,1.318 0.252,1.318 false 0.11,0.436 0.282,0.587 0.172,0.151 10 F 1.371,0.193 1.555,0.355 0.184,0.163 10 D 1.086,0.681 1.269,0.844 0.184,0.163 10 P 0.102,1.016 0.285,1.179 0.184,0.163 10 P 0.106,0.741 0.290,0.904 0.184,0.163 10 P 0.11,1.254 0.294,1.417 0.184,0.163 10 P

a.

Install the 3 plates, 3 discs and flange.

Install in order:

P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.
C162748

Temporarily install the snap ring.


c.
C210196E01
1.983,2.608 2.826,2.835 0.842,0.227 10 Distance (A) 1.634,3.397 1.87,2.689 1.87,2.689 1.938,2.689 false 2.641,1.026 2.279,2.121 2.279,2.121 2.365,2.121 false 2.408,2.034 2.971,2.220 0.563,0.186 10 Oil Hole

Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration.

Standard moving distance (A):

0.30 to 0.60 mm (0.0118 to 0.0236 in.)


If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
0 2.95 to 3.05 mm (0.116 to 0.120 in.)
1 3.05 to 3.15 mm (0.120 to 0.124 in.)
2 3.15 to 3.25 mm (0.124 to 0.128 in.)
3 3.25 to 3.35 mm (0.128 to 0.132 in.)
4 3.35 to 3.45 mm (0.132 to 0.136 in.)
5 3.45 to 3.55 mm (0.136 to 0.140 in.)
6 3.55 to 3.65 mm (0.140 to 0.144 in.)
7 3.65 to 3.75 mm (0.144 to 0.148 in.)
8 3.75 to 3.85 mm (0.148 to 0.152 in.)
A 3.85 to 3.95 mm (0.152 to 0.156 in.)



d.

Temporarily remove the snap ring, replace the flange with the selected flange and reinstall the snap ring.


Hide 34360B 38.INSTALL UNDERDRIVE 1-WAY CLUTCH ASSEMBLY

C161643

a.

Install the No. 2 clutch hub thrust washer to the coast clutch hub.

HINT:

Use a small amount of MP grease to make the thrust washer stay securely in place.



b.

Install the 1-way clutch to the coast clutch hub.


Hide 35064 40.INSTALL COAST CLUTCH HUB SUB-ASSEMBLY WITH UNDERDRIVE 1-WAY CLUTCH ASSEMBLY

C163077E05
1.854,0.198 2.24,0.198 false 1.813,1.219 2.24,1.219 false 1.823,0.99 2.25,0.875 false 2.313,1.146 3,1.354 0.688,0.208 10 false Bearing C 2.292,0.104 2.969,0.302 0.677,0.198 10 false Bearing D 2.302,0.781 2.833,0.969 0.531,0.188 10 false Race C

a.

Install the 2 thrust needle roller bearings, thrust bearing race and coast clutch hub with the underdrive 1- way clutch to the input shaft.

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings and race stay securely in place.


Bearing and Race Diameter:
Item Inside Outside
Bearing C 21.35 to 21.60 mm (0.841 to 0.850 in.) 40.72 to 40.92 mm (1.60 to 1.61 in.)
Race C 22.65 to 22.90 mm (0.892 to 0.902 in.) 44.50 to 44.75 mm (1.75 to 1.76 in.)
Bearing D 35.65 to 35.9 mm (1.40 to 1.41 in.) 56.3 to 56.55 mm (2.22 to 2.23 in.)



Hide 35633B 41.INSTALL FORWARD MULTIPLE DISC CLUTCH DISC SET

C210198E01
0.966,1.028 1.122,1.205 0.156,0.177 10 D 2.351,0.856 2.507,1.033 0.156,0.177 10 F 2.339,2.73 2.495,2.907 0.156,0.177 10 P 2.187,2.813 2.327,2.813 false 2.339,2.354 2.495,2.532 0.156,0.177 10 P 2.187,2.438 2.327,2.438 false 2.339,1.979 2.495,2.157 0.156,0.177 10 P 2.187,2.063 2.327,2.063 false 2.339,1.604 2.495,1.781 0.156,0.177 10 P 2.187,1.688 2.327,1.688 false 2.339,1.229 2.495,1.406 0.156,0.177 10 P 2.187,1.313 2.327,1.313 false 1.118,1.11 1.258,1.11 false 0.966,1.403 1.122,1.580 0.156,0.177 10 D 1.118,1.485 1.258,1.485 false 0.966,1.778 1.122,1.955 0.156,0.177 10 D 1.118,1.86 1.258,1.86 false 0.966,2.153 1.122,2.330 0.156,0.177 10 D 1.118,2.235 1.258,2.235 false 0.966,2.528 1.122,2.705 0.156,0.177 10 D 1.118,2.61 1.258,2.61 false 2.187,0.938 2.327,0.938 false

a.

Install the 5 plates, 5 discs and flange to the input shaft.

Install in order:

P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.
D028519

Temporarily install the snap ring.


c.
C210197E01
1.564,2.405 2.433,2.626 0.869,0.221 10 Distance (A) 2.547,2.034 3.132,2.245 0.585,0.211 10 Oil Hole 2.645,1.03 2.428,2.112 2.428,2.112 2.497,2.112 false

Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration.

Standard moving distance (A):

0.7 to 1.0 mm (0.0276 to 0.0394 in.)


If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
0 2.95 to 3.05 mm (0.116 to 0.120 in.)
1 3.05 to 3.15 mm (0.120 to 0.124 in.)
2 3.15 to 3.25 mm (0.124 to 0.128 in.)
3 3.25 to 3.35 mm (0.128 to 0.132 in.)
4 3.35 to 3.45 mm (0.132 to 0.136 in.)
5 3.45 to 3.55 mm (0.136 to 0.140 in.)
6 3.55 to 3.65 mm (0.140 to 0.144 in.)
7 3.65 to 3.75 mm (0.144 to 0.148 in.)
8 3.75 to 3.85 mm (0.148 to 0.152 in.)
9 3.85 to 3.95 mm (0.152 to 0.156 in.)
A 3.95 to 4.05 mm (0.156 to 0.159 in.)



d.

Temporarily remove the snap ring, replace the flange with the selected flange and reinstall the snap ring.


Hide 35712A 42.INSTALL INPUT SHAFT OIL SEAL RING

a.

Coat 4 new oil seal rings with ATF.


b.
C162568E03
1.531,0.333 2.229,0.677 0.698,0.344 10 true CORRECT 1.49,1.479 2.365,1.792 0.875,0.313 10 true INCORRECT

Overlap the seal ring ends in the axial direction.

NOTICE:
·

Overlapping the seal ring ends in the axial direction prevents damage to the seal ring.

·

Do not overlap the seal ring ends in the radial direction, as this may damage the seal ring.




c.
C161649E01
0.943,0.169 2.118,0.409 1.176,0.240 10 New Oil Seal Ring 0.677,0.84 0.468,1.411 false 0.677,0.84 0.788,0.261 0.788,0.261 0.898,0.261 false 0.677,0.84 1.036,1.252 false 0.653,1.355 0.677,0.84 false 0.837,1.306 0.677,0.84 false

Squeeze the ends of the 4 oil seal rings together, and then install them to the input shaft groove.

NOTICE:

Do not excessively widen the rings.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 35701 43.INSTALL INPUT SHAFT ASSEMBLY

C161648

a.

Install the input shaft to the clutch drum.


Hide 35061 44.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

C161641

a.

Install the No. 3 clutch hub thrust washer, forward clutch hub and thrust needle roller bearing to the clutch drum.

NOTICE:

Before installing the forward clutch hub, apply ATF to the forward clutch hub bush sliding surfaces. After the installation, check that the forward clutch hub rotates smoothly.


HINT:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust washer stay securely in place.


Bearing Diameter:
Item Inside Outside
Bearing E 42.55 to 42.80 mm (1.68 to 1.69 in.) 60.84 to 61.14 mm (2.40 to 2.41 in.)



Hide 35049 45.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

C162750

a.

Install the reverse clutch hub to the clutch drum.

NOTICE:

Before installing the reverse clutch hub, apply ATF to the reverse clutch hub bush sliding surfaces. After the installation, check that the reverse clutch rotates smoothly.



Hide 35677C 46.INSTALL REAR CLUTCH DISC SET

C175546E01
1.123,1.063 0.966,1.063 false 2.457,1.214 2.3,1.214 false 2.457,1.511 2.3,1.511 false 2.457,1.807 2.3,1.807 false 2.457,2.104 2.3,2.104 false 2.457,2.4 2.3,2.4 false 1.124,1.367 0.966,1.367 false 1.123,1.656 0.966,1.656 false 1.123,1.953 0.966,1.953 false 1.124,2.249 0.966,2.249 false 1.123,2.546 0.966,2.546 false 0.678,0.984 0.925,1.155 0.247,0.171 10 S/F 0.817,1.281 0.960,1.452 0.142,0.171 10 P 0.817,1.568 0.960,1.739 0.142,0.171 10 P 0.817,1.875 0.960,2.047 0.142,0.171 10 P 0.817,2.173 0.960,2.344 0.142,0.171 10 P 0.817,2.47 0.960,2.641 0.142,0.171 10 F 2.489,1.127 2.635,1.303 0.146,0.176 10 D 2.457,0.867 2.33,0.867 false 2.489,0.779 2.635,0.955 0.146,0.176 10 C 2.489,1.425 2.635,1.601 0.146,0.176 10 D 2.489,1.723 2.635,1.899 0.146,0.176 10 D 2.489,2.021 2.635,2.196 0.146,0.176 10 D 2.489,2.319 2.635,2.494 0.146,0.176 10 D

a.

Install the flange, 5 discs, 4 plates, selected flange, cushion plate and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - P - D - S/F - C


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected flange

C = Cushion plate



b.

Using a screwdriver, install the snap ring to the clutch drum.


Hide 35780B 47.INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

C161634

a.

Install the clutch drum thrust washer to the clutch drum.

HINT:

Use a small amount of MP grease to make the thrust washer stay securely in place.



b.

Install the 1-way clutch to the clutch drum.


Hide 49.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161633E05
0.594,0.26 0.479,0.26 0.479,0.26 0.302,1.146 false 0.938,1.813 0.813,1.813 0.813,1.813 0.76,1.531 false 0.656,0.167 1.333,0.406 0.677,0.24 10 false Bearing A 0.979,1.729 1.656,1.969 0.677,0.24 10 false Bearing B

a.

Install the 2 thrust needle roller bearings.

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.


Bearing Diameter:
Item Inside Outside
Bearing A 71.96 to 72.26 mm (2.83 to 2.84 in.) 85.25 to 85.6 mm (3.36 to 3.37 in.)
Bearing B 34.65 to 34.85 mm (81.36 to 1.37 in.) 51.56 to 51.86 mm (2.03 to 2.04 in.)



b.

Coat the clutch drum thrust washer with petroleum jelly and install it to the clutch drum and input shaft assembly.


c.
C164078

Install the clutch drum and input shaft assembly to the transmission case.


Hide 50.INSTALL OIL PUMP ASSEMBLY

C161631

a.

Coat a new O-ring with ATF, and install it to the oil pump.


b.

Install the 2 thrust bearing races to the front oil pump.

Thrust Bearing Race Diameter:
Item Inside Outside
Race A 74.26 to 74.56 mm (2.92 to 2.94 in.) 87.39 to 87.74 mm (3.44 to 3.45 in.)
Race B 37.0 to 37.3 mm (1.46 to 1.47 in.) 52.1 to 52.3 mm (2.05 to 2.06 in.)



c.
D027921

Pass the input shaft through the center hole of the oil pump, and align the bolt holes of the oil pump assembly with the transmission case.


d.

Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.


e.

Apply seal packing to the flanges of the bolts.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent



f.

Install the oil pump with the 10 bolts.

Torque:
21 N*m (215 kgf*cm, 16 ft.*lbf)

NOTICE:

During installation, do not allow oil to contact the bolts or the surface of the oil pump body.



Hide 35506F 52.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

D028548

a.

Using SST, tap in 2 new oil seals.

SST
09350-30020  (09350-07110)

Standard depth:

-0.3 to 0.3 mm (-0.0118 to 0.0118 in.)



b.

Coat the lips of the oil seals with MP grease.


Hide 35505 53.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

D028798E06
1.052,0.99 0.927,0.292 0.927,0.292 0.698,0.292 false 0.719,1 0.51,1.292 false 0.156,1.292 0.969,1.656 0.813,0.365 10 false Manual Valve Lever 0.135,0.188 0.615,0.323 0.479,0.135 10 false Spacer

a.

Install a new spacer to the manual valve lever.


b.

Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the shaft.


c.
D028799

Using a hammer, tap in a new spring pin.


d.
D028800

Align the manual valve lever indentation with the spacer hole, and stake them together with the punch.


e.

Check that the shaft rotates smoothly.


Hide 35556 54.INSTALL PARKING LOCK PAWL SHAFT

D028846E09
2.229,1.521 1.896,1.448 true 2.25,0.813 1.938,0.865 true 0.969,0.198 0.656,0.25 true 0.042,0.167 0.729,0.75 0.688,0.583 10 true Parking Lock Pawl 1.469,0.781 1.906,1.125 0.438,0.344 10 true E-Ring 1.427,1.333 1.865,1.708 0.438,0.375 10 true Spring

a.

Install a new E-ring to the shaft.


b.

Install the parking lock pawl, shaft and spring.


Hide 35501 55.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

D012709E01
2.973,0 3.414,0.134 0.441,0.134

a.

Connect the parking lock rod to the manual valve lever.


Hide 35595 56.INSTALL PARKING LOCK PAWL BRACKET

D012708

a.

Install the parking lock pawl bracket to the transmission case with the 3 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


b.
U152681E02
2.938,0.417 2.281,0.469 false 0.542,1.469 0.76,1.792 0.76,1.792 0.813,1.792 false 0.385,0.01 1.698,0.333 1.313,0.323 10 true Planetary Ring Gear 1,0.406 2.25,0.781 1.25,0.375 10 true Manual Valve Lever 0.906,1.719 1.583,2.052 0.677,0.333 10 true Lock Pawl

Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked by the lock pawl.


Hide 35427T 57.INSTALL B-1 ACCUMULATOR VALVE

C162753

a.

Install the 2 springs and accumulator valve to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
B-1 Inner 44.98 mm (1.77 in.)
11.3 mm (0.445 in.)
Natural
B-1 Outer 46.36 mm (1.83 in.)
17.1 mm (0.673 in.)
Natural



Hide 35426D 58.INSTALL C-3 ACCUMULATOR PISTON

C352754E01
2.927,0.74 2.927,0.479 2.927,0.479 2.563,0.271 false 2.927,0.49 2.594,0.438 false 2.594,0.813 3.385,1.104 0.792,0.292 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the piston.


b.

Install the 2 springs and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-3 Inner 44.0 mm (1.73 in.)
14.0 mm (0.551 in.)
Yellow
C-3 Outer 73.35 mm (2.89 in.)
19.9 mm (0.783 in.)
Red



Hide 35427K 59.INSTALL B-3 ACCUMULATOR PISTON

C352755E01
1.344,0.229 1,0.479 1,0.479 1.333,0.427 false 0.333,0.51 1.177,0.708 0.844,0.198 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
B-3 70.5 mm (2.78 in.)
19.7 mm (0.776 in.)
Purple



Hide 35425A 60.INSTALL C-2 ACCUMULATOR PISTON

C352756E01
1.667,0.531 1.344,0.563 1.344,0.563 1.646,0.302 false 0.656,0.563 2.188,0.76 1.531,0.198 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-2 62.0 mm (2.44 in.)
15.9 mm (0.626 in.)
White



Hide 35251 61.INSTALL CHECK BALL BODY

D027914E26
1.552,1.313 0.719,1.313 true 1.281,0.458 0.865,0.458 false 0.208,0.375 0.917,0.688 0.708,0.313 10 false Check Ball Body 0.302,1.208 0.76,1.406 0.458,0.198 10 false Spring

a.

Install the spring and check ball body.


Hide 35159 62.INSTALL BRAKE DRUM GASKET

D027969

a.

Install 3 new brake drum gaskets.


Hide 35145C 63.INSTALL TRANSMISSION CASE GASKET

D027968E13
2.042,1.563 2.385,1.438 false 2.417,1.344 2.917,1.677 0.5,0.333 10 true Gasket

a.

Install 3 new transmission case gaskets.


Hide 35410 64.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

C157293E08
1.75,1.229 2.375,0.719 true 2.438,0.604 2.708,0.948 0.271,0.344 10 true Pin

a.

Align the hole of the manual valve with the pin of the lever and connect the pin to the manual valve.


b.
C157292E07
0.385,0.313 0.5,0.177 0.5,0.177 0.625,0.333 true 0.417,0.677 0.177,0.771 0.177,0.771 0.458,1.271 true 0.427,0.865 0.177,0.771 true 0.365,1.542 0.156,1.563 0.156,1.563 0.333,1.698 true 0.771,1.885 0.833,2.01 true 1.708,1.542 1.448,1.427 true 1.708,1.771 1.49,2.042 1.49,2.042 1.979,1.844 true 2.635,1.781 2.5,1.885 2.5,1.885 2.365,1.823 true 2.365,1.51 2.5,1.26 true 2.948,1.375 3.219,1.458 3.219,1.458 2.99,1.688 true 3.219,1.458 2.979,1.5 true 3.229,1.094 2.948,1.031 true 2.969,0.781 3.24,0.781 true 0.021,0.635 0.146,0.792 0.125,0.156 10 false A 0.031,1.479 0.167,1.656 0.135,0.177 10 false B 0.448,0.01 0.583,0.188 0.135,0.177 10 false B 0.813,2 0.948,2.167 0.135,0.167 10 true B 1.354,2 1.49,2.177 0.135,0.177 10 true B 1.292,1.313 1.427,1.49 0.135,0.177 10 true C 3.25,1.375 3.385,1.552 0.135,0.177 10 false B 3.25,1.01 3.385,1.188 0.135,0.177 10 false D 2.5,1.073 2.635,1.25 0.135,0.177 10 true D 3.26,0.698 3.396,0.875 0.135,0.177 10 false C 2.531,1.906 2.667,2.083 0.135,0.177 10 true B

Install the valve body with the 19 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

36 mm (1.42 in.) for bolt A

25 mm (0.984 in.) for bolt B

45 mm (1.77 in.) for bolt C

50 mm (1.97 in.) for bolt D



c.

Install the detent spring and detent spring cover with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82125J 65.INSTALL TRANSMISSION WIRE

D027912E01
3.007,0 3.414,0.108 0.407,0.108

a.

Coat a new O-ring with ATF, and install it to the transmission wire connector.


b.

Install the transmission wire.


c.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
C351958E01
0.635,0.823 1.01,1.021 true 0.656,1.448 0.99,1.448 true 0.125,0.74 0.625,1.031 0.5,0.292 10 true Orange 0.313,1.375 0.656,1.667 0.344,0.292 10 true Blue

Connect the 9 solenoid connectors.


e.

Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

12 mm (0.472 in.) for bolt A

36 mm (1.42 in.) for bolt B



f.

Attach the wire harness to the 2 clamps.


Hide 35330 66.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C209698

a.

Coat a new O-ring with ATF, and install it to the oil strainer.


b.

Install the oil strainer with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35394 67.INSTALL TRANSMISSION OIL CLEANER MAGNET

C210199

a.

Install the 4 magnets.


Hide 35106 68.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C210200

a.

Install a new gasket to the oil pan.


b.

Install the oil pan with the 20 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Install a new gasket and the drain plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35015J 69.INSTALL EXTENSION HOUSING REAR OIL SEAL

a.

Coat the lip of a new oil seal with ATF.


b.
C177436E06
1.219,1.031 0.375,1.167 true 0.052,1.104 0.375,1.271 0.323,0.167 10 false SST 2.313,1.229 3.146,1.438 0.833,0.208 10 false 0 to 0.5 mm

Using SST and a hammer, tap in the oil seal.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)

Standard depth:

0 to 0.5 mm (0 to 0.0197 in.)



Hide 35015G 70.INSTALL REAR TRANSFER ADAPTER

a.

Install the transfer adapter hole snap ring.


b.

Clean the threads of the bolts and transfer adapter.


c.
C175554E07
2.021,0.385 2.146,0.125 2.146,0.125 2.229,0.125 false 2.281,0.063 3.177,0.271 0.896,0.208 10 false Seal Packing 0.813,1.813 2.583,2.01 1.771,0.198 10 false Seal Diameter: 1 to 1.5 mm

Apply seal packing or equivalent to the transfer adapter.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent


Seal diameter:

1.0 to 1.5 mm (0.0394 to 0.0591 in.)



d.

Apply adhesive to the threads of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324,

Three Bond 1324 or equivalent



e.
U152371E02
2.385,0.375 2.521,0.531 0.135,0.156 10 false A 2.469,1.24 2.604,1.396 0.135,0.156 10 false A 2.625,1.833 2.75,1.99 0.125,0.156 10 false B 2.073,1.885 2.198,2.042 0.125,0.156 10 false B 0.844,0.375 0.979,0.531 0.135,0.156 10 false A 0.76,1.24 0.896,1.396 0.135,0.156 10 false A 0.604,1.833 0.729,1.99 0.125,0.156 10 false B 1.167,1.885 1.292,2.042 0.125,0.156 10 false B

Install the extension housing with the 6 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)

HINT:

Each bolt length is indicated below.

50 mm (1.97 in.) for bolt A

40 mm (1.57 in.) for bolt B



Hide 35111 71.INSTALL AUTOMATIC TRANSMISSION HOUSING

U115895E04
2.292,0.198 2.427,0.354 0.135,0.156 10 false A 2.021,0.063 2.156,0.219 0.135,0.156 10 false A 1.365,0.052 1.5,0.208 0.135,0.156 10 false A 1.083,0.208 1.219,0.365 0.135,0.156 10 false A 0.708,1.094 0.844,1.25 0.135,0.156 10 false A 2.667,1.125 2.802,1.281 0.135,0.156 10 false A 2.521,1.656 2.646,1.813 0.125,0.156 10 false B 0.854,1.646 0.979,1.802 0.125,0.156 10 false B 1.135,1.781 1.26,1.938 0.125,0.156 10 false C 2.229,1.771 2.354,1.927 0.125,0.156 10 false C

a.

Clean the threads of the bolts and case with non-residue solvent.


b.

Apply adhesive to the threads of the 4 bolts labeled B and C.

Adhesive:

Toyota Genuine Adhesive 1324,

Three Bond 1324 or equivalent



c.

Install the transmission housing with the 10 bolts.

Torque:
for 14 mm head bolt A : 34 N*m (345 kgf*cm, 25 ft.*lbf)
for 17 mm head bolt B : 57 N*m (579 kgf*cm, 42 ft.*lbf)
for 14 mm head bolt C : 34 N*m (345 kgf*cm, 25 ft.*lbf)


Hide 35122 72.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

U115758

a.

Coat a new O-ring with ATF and install it to the breather tube.


b.

Install the breather tube with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 89413B 73.INSTALL SPEED SENSOR

a.
C111258

Coat 2 new O-rings with ATF, and install one to each speed sensor.


b.

Install the 2 speed sensors.


c.

Install the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 32921C 74.INSTALL OIL COOLER TUBE UNION

C159633E02
2.74,1.5 3.208,1.75 0.469,0.25 10 true 0 +/-2°

a.

Coat 2 new O-rings with ATF, and install them to the 2 oil cooler tube unions.


b.

Install the 2 oil cooler tube unions.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 84540 75.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903

a.

Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.


b.

Install a new lock washer and the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C155873E04
1.906,0.052 2.052,0.219 0.146,0.167 10 false N 1.021,0.302 1.146,0.469 0.125,0.167 10 false P 1.573,0.292 1.719,0.458 0.146,0.167 10 false R

Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


d.
C351960E01
1.948,0.938 1.75,0.115 1.75,0.115 2,0.115 true 1.958,1.542 0.729,1.073 0.729,1.073 0.542,1.073 true 2.052,0.042 3.26,0.208 1.208,0.167 10 false Neutral Basic Line 0.083,0.979 0.708,1.135 0.625,0.156 10 false Groove

Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


e.
D027990

Using a screwdriver, bend the tabs of the lock washer.

HINT:

Bend at least 2 of the lock washer tabs.



Hide 35572 76.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

C155869

a.

Install the control shaft lever RH with the washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)