Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234175 AUTOMATIC TRANSMISSION SYSTEM C

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NT with the output speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, and as a result, the gears shift smoothly.

DTC Code DTC Detection Condition Trouble Area
P0717 All conditions are met for 5 seconds or more (1-trip detection logic):
(a) Gear change is not performed.
(b) Gear position is 4th, 5th or 6th.
(c) Transmission input shaft speed is less than 300 rpm.
(d) Transmission output shaft speed is 1000 rpm or more.
(e) Park/neutral position switch NSW and R input signals are OFF.
(f) Shift solenoid valves and the park/neutral position switch are operating normally.
·

Open or short in speed sensor NT circuit

·

Speed sensor NT

·

ECM

·

Automatic transmission (clutch, brake, gear, etc.)



Reference: Inspect using an oscilloscope.

Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
D74-124 (NT+) - D74-123 (NT-) 1 V/DIV., 2 msec./DIV. Engine is idling (Shift lever in P or N) Refer to illustration


C162170E04
2.707,0.097 3.292,0.298 0.585,0.201 10 1 V/DIV. 2.995,0.904 3.347,1.106 0.352,0.202 10 GND 1.637,1.688 2.453,1.883 0.816,0.195 10 2 msec./DIV.

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal by comparing the input speed sensor NT signal with the output speed sensor SP2 signal.

While the vehicle is operating in 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
·

*1: A pulse is not output or is irregularly output.

·

*2: The vehicle speed is approximately 50 km/h (30 mph) or more.



MONITOR STRATEGY

Related DTCs P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main) Speed sensor (NT)
Required sensors/Components (Related) Speed sensor (SP2)
Frequency of operation Continuous
Duration 5 seconds
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present P0705 (Park/neutral position switch circuit)
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
P0761, P0979, P0980 (Shift solenoid valve S3)
P0766, P0982, P0983 (Shift solenoid valve S4)
P0748 (Shift solenoid valve SL1 circuit)
P0776, P0778 (Shift solenoid valve SL2)
Shift change After shift change is completed and before starting next shift change operation
ECM selected gear 4th, 5th or 6th
Output shaft rpm 1000 rpm or more
NSW switch OFF
R switch OFF
Engine Running
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Speed sensor signal rpm Less than 300 rpm

COMPONENT OPERATING RANGE

Speed sensor signal rpm 300 rpm or more

WIRING DIAGRAM

C155187E65
5.642,1.067 6.204,1.269 0.561,0.202 10 NT+ 5.642,2.2 6.204,2.401 0.561,0.202 10 NT- 5.248,1.193 5.587,1.395 0.339,0.202 10 124 0.655,2.581 1.980,2.783 1.325,0.202 10 Speed Sensor NT 5.248,2.326 5.587,2.528 0.339,0.202 10 123 0.655,2.395 0.987,2.597 0.332,0.202 10 D65 5.83,3.014 6.162,3.216 0.332,0.202 10 D74 1.285,1.208 1.447,1.409 0.162,0.202 10 2 5.83,3.2 6.222,3.401 0.392,0.202 10 ECM 1.285,2.056 1.447,2.258 0.162,0.202 10 1

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm.

HINT:
·

SPD (NT) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR NT INSTALLATION
a.
C211922E01
0.838,0.127 1.078,0.329 0.240,0.202 10 *a 2.303,0.127 2.543,0.329 0.240,0.202 10 *b

Check the speed sensor NT installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.


Text in Illustration
*a CORRECT
*b INCORRECT



OK

2.INSPECT SPEED SENSOR NT

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR NT

2.INSPECT SPEED SENSOR NT
a.
C206284E03
0.056,0.003 0.296,0.205 0.240,0.202 10 *a 1.303,1.682 1.603,1.103 false 1.196,1.707 1.643,1.909 0.446,0.202 10 2 2.15,1.682 1.852,1.103 false 2.152,1.707 2.598,1.909 0.446,0.202 10 1

Disconnect the D65 speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω


Text in Illustration
*a Component without harness connected
(Speed Sensor NT)



OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)
a.
U152392E02
2.031,1.792 1.708,1.333 false 1.302,1.802 1.625,1.344 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.604,0.281 1.979,0.51 0.375,0.229 10 false D74 0.865,1.823 1.521,2.021 0.656,0.198 10 false 123 (NT-) 1.781,1.802 2.479,2 0.698,0.198 10 false 124 (NT+)

Disconnect the D74 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-124 (NT+) - D74-123 (NT-) 20°C (68°F) 560 to 680 Ω
D74-124 (NT+) - Body ground Always 10 kΩ or higher
D74-123 (NT-) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR