Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2015.08–2016.08
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234175 AUTOMATIC TRANSMISSION SYSTEM C

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0711  Transmission Fluid Temperature Sensor "A" Performance  


DESCRIPTION

The ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM.

The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The ECM calculates the fluid temperature based on the voltage signal.

DTC Code DTC Detection Condition Trouble Area
P0711 Either condition is met (2-trip detection logic):

(a) Certain monitor enabling conditions are met and the ATF temperature is below 20°C (68°F).

(b) Certain monitor enabling conditions are met and the ATF temperature is 110°C (230°F) or higher.


Transmission wire (No. 1 ATF temperature sensor)

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output from the Automatic Transmission Fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit or a fault in the ATF temperature sensor.

After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the MIL and stores the DTC.

When the ATF temperature is 105°C (221°F) or more and the engine coolant temperature takes 10 seconds or more to reach 60°C (140°F) after a cold start, the ECM also determines this as a fault, turns on the MIL and stores the DTC.

MONITOR STRATEGY

Related DTCs P0711: ATF temperature sensor/Rationality check
Required sensors/Components ATF temperature sensor
Frequency of operation Continuous
Duration Condition (A), (B), (C) and (D): 3 seconds
Condition (E): Continuous
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor "A" circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine Coolant Temperature) sensor circuit)
P0110, P0111, P0112, P0113 (IAT (Intake air temperature) sensor circuit)
P2610 (Soak timer circuit)

Condition (A)
Duration time from engine start 12 seconds or more
ECT -15°C (5°F) or higher
Permission flag for ATF temperature rationality check ON
Time after engine start except for continuing shift position "N" or "P"*2 5 minutes or more
Accumulated driving time*1 75 seconds or more
Driving distance after engine start*3 4.7 km (3.0 miles) or more
ECT (12 seconds after engine start) 15°C (59°F) or higher
IAT*4 15°C (59°F) or higher
Soak time 5 hours or more

Condition (B)
Duration time from engine start 12 seconds or more
ECT -15°C (5°F) or higher
Permission flag for ATF temperature rationality check ON
Time after engine start except for continuing shift position "N" or "P"*2 21 minutes and 40 seconds or more
Accumulated driving time*1 140 seconds or more
Driving distance after engine start*3 9.0 km (5.6 miles) or more
ECT (12 seconds after engine start) -10°C (14°F) or higher
IAT*4 -10°C (14°F) or higher

Condition (C)
Duration time from engine start 12 seconds or more
ECT -15°C (5°F) or higher
Permission flag for ATF temperature rationality check ON
Time after engine start except for continuing shift position "N" or "P"*2 30 minutes or more
Accumulated driving time*1 400 seconds or more
Driving distance after engine start*3 16.0 km (9.9 miles) or more
ECT (12 seconds after engine start) -15°C (5°F) or higher
IAT*4 -15°C (5°F) or higher

Condition (D)
Duration time from engine start 12 seconds or more
ECT -15°C (5°F) or higher
Permission flag for ATF temperature rationality check ON
Time after engine start except for continuing shift position "N" or "P"*2 55 minutes or more
Accumulated driving time*1 750 seconds or more
Driving distance after engine start*3 27.0 km (16.8 miles) or more

Condition (E)
Duration time for ECT to reach 60°C (140°F) 10 seconds or more
ATF temperature (12 seconds after engine start) 110°C (230°F) or higher
ECT (12 seconds after engine start) Below 35°C (95°F)

HINT:
*1: Following conditions are met
Engine speed - Turbine speed 50 rpm or more
Output speed 400 rpm or more
Throttle valve opening angle 5.5% or more
Shift position Not "N" or "P"
Engine Starting
However, accumulated driving time is cleared -
When following condition met -
Duration time from shift position "N" or "P" 5 minutes or more

*2: Time after engine start is cleared when following condition met
Duration time from shift position "N" or "P" 5 minutes or more

*3: Driving distance is cleared when following condition met
Duration time from shift position "N" or "P" 5 minutes or more

*4: IAT is measured when either of following conditions met
12 sec. after engine start -
Duration time from shift position "N" or "P" 5 minutes or more



TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition (A), (B), (C), (D) or (E)

Condition (A), (B), (C) and (D)
ATF temperature Below 20°C (68°F)

Condition (E)
ATF temperature 110°C (230°F) or higher

COMPONENT OPERATING RANGE

Condition (A), (B), (C), (D) and (E)
ATF temperature 20°C (68°F) or higher, and below 110°C (230°F)

CAUTION / NOTICE / HINT

NOTICE:
·
·

If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the Techstream first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P2610 (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).



DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approximately 80°C (176°F)

·

Equal to ambient temperature when engine cold


If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.

HINT:

When DTC P0712 is output and the Techstream output is 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the Techstream output is -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the tester in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored.

It is not necessary to inspect the circuit when P0711 is stored.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0711)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the Techstream.

Result
Result Proceed to
Only P0711 is output A
P0711 and other DTCs are output B

HINT:

If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.




A

2.CHECK TRANSMISSION FLUID LEVEL

B

2.CHECK TRANSMISSION FLUID LEVEL
a.

Check the transmission fluid level (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION FLUID>ADJUSTMENT).

OK:

Automatic transmission fluid level is correct.




OK

NG