Home › Drivetrain › A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049127 A760F AUTOMATIC TRANSMISSION / TRANSAXLE _0234175 AUTOMATIC TRANSMISSION SYSTEM C

A760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0982  Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)  P0983  Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending current to the open or short-circuited solenoid (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0982 ECM detects a short in the solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip detection logic).
·

Short in shift solenoid valve S4 circuit

·

Shift solenoid valve S4

·

ECM


P0983 ECM detects an open in the solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip detection logic).
·

Open in shift solenoid valve S4 circuit

·

Shift solenoid valve S4

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S4 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S4 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S4 circuit.

When the shift solenoid valve S4 is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open in the shift solenoid valve S4 circuit (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

MONITOR STRATEGY

Related DTCs P0982: Shift solenoid valve S4/Range check (Low resistance)
P0983: Shift solenoid valve S4/Range check (High resistance)
Required sensors/Components Shift solenoid valve S4
Frequency of operation Continuous
Duration 0.128 seconds or more
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present None
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

P0982: Range Check (Low Resistance)
Command to shift solenoid valve S4 ON

P0983: Range Check (High Resistance)
Command to shift solenoid valve S4 OFF

TYPICAL MALFUNCTION THRESHOLDS

P0982: Range Check (Low Resistance)
Shift solenoid valve S4 resistance 8 Ω or less

P0983: Range Check (High Resistance)
Shift solenoid valve S4 resistance 100 kΩ or more

COMPONENT OPERATING RANGE

Shift solenoid valve S4 resistance 11 to 15 Ω at 20°C (68°F)

WIRING DIAGRAM

C352874E04
2.479,0.875 2.792,1.073 0.313,0.198 10 false S4 2.781,1.135 3.094,1.333 0.313,0.198 10 false 19 1.021,1.719 2.51,1.927 1.49,0.208 10 false Shift Solenoid Valve S4 0.948,2.792 1.365,2.969 0.417,0.177 10 false D83 0.958,2.979 2.781,3.188 1.823,0.208 10 false Transmission Wire 5.5,1.125 5.813,1.323 0.313,0.198 10 false 5 5.74,1 6.052,1.198 0.313,0.198 10 false S4 5.917,3.073 6.25,3.271 0.333,0.198 10 false D74 5.917,3.24 6.406,3.438 0.49,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


HINT:

The shift solenoid valve S4 is turned ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S4 OFF OFF OFF OFF ON ON


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)
a.
C210154E19
0.057,0.005 0.373,0.206 0.317,0.202 10 *a 1.129,1.819 1.529,2.021 0.400,0.202 10 S4 1.283,1.794 1.49,1.367 false

Disconnect the D83 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
19 (S4) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S4
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U152399E02
0.615,1.802 0.99,0.854 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 1.594,0.281 1.969,0.51 0.375,0.229 10 false D74 0.365,1.813 1.021,2.01 0.656,0.198 10 false 5 (S4)

Disconnect the D74 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-5 (S4) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR