The ECM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical problems of the shift solenoid valve SLU, valve body and torque converter.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2-trip detection logic). | ·
Shift solenoid valve SLU remains open or closed ·
Valve body is blocked ·
Shift solenoid valve SLU ·
Torque converter ·
Automatic transmission (clutch, brake, gear, etc.) ·
Line pressure is too low |
Torque converter lock-up is controlled by the ECM based on the turbine (input) speed sensor NT, output speed sensor SP2, engine speed, engine load, engine temperature, vehicle speed, transmission temperature and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing input turbine speed (NT) to the output shaft speed (SP2). When conditions are appropriate, the ECM requests lock-up by applying control voltage to the shift solenoid SLU. When the SLU is turned ON, it applies pressure to the lock-up relay valve and locks the torque converter.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the shift solenoid valve SLU or lock-up system performance.
The ECM will illuminate the MIL and store the DTC.
Example:
When one of the following conditions is met, the system determines that there is a malfunction.
There is a difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up ON.
Engine speed is at least 70 rpm more than input turbine speed.
There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up OFF.
The difference between engine speed and input turbine speed is less than 35 rpm.
| Related DTCs | P2757: Shift solenoid valve SLU/Functional check |
| Required sensors/Components | Shift solenoid valve SLU |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A)
2 seconds OFF malfunction (B) 0.4 seconds ON malfunction 1.8 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit)
P0500 (Output speed sensor circuit) P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 2nd, 3rd, 4th, 5th or 6th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| Transfer position | HIGH* |
*: Following conditions are met
| Vehicle speed sensor "A" circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| Transfer input speed / Transfer output speed (NO / NOtf) | 0.9 or more, and less than 1.1 |
| ECM lock-up command | ON
(SLU pressure: 513 kPa (5.2 kgf/cm2, 74 psi) or more) |
| Duration time from lock-up on command | 3 seconds or more |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
0.65 to 0.79
or 0.51 to 0.65 |
| Calculated load value | A/C off:
21.6% or more when turbine speed is 1200 rpm A/C on: 21.6% or more when turbine speed is 1200 rpm (Conditions vary with turbine speed) |
| Vehicle speed | Less than 120 km/h (74.6 mph) |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 6.6% or more at 2000 rpm
(Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off)
7.75% or more (A/C on) |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
3.30 to 7.50
or 1.91 to 2.35 or 1.28 to 1.53 or 0.93 to 1.07 or 0.65 to 0.79 or 0.51 to 0.65 |
| ECM lock-up command | OFF
(SLU pressure: Less than 4 kPa (0.04 kgf/cm2, 0.6 psi)) |
| Duration time from lock-up off command | 3 seconds or more |
| Throttle valve opening angle | 6% or more |
| Input speed/output speed (NT/NO)
NT: Input (Turbine) speed NO: Internal counter shaft speed |
1.91 to 2.35
or 1.28 to 1.53 or 0.93 to 1.07 or 0.65 to 0.79 or 0.51 to 0.65 |
| Calculated load value | A/C off:
21.6% or more when turbine speed is 1200 rpm A/C on: 21.6% or more when turbine speed is 1200 rpm (Conditions vary with turbine speed) |
| Vehicle speed | Less than 120 km/h (74.6 mph) |
Both of the following conditions are met: OFF malfunction (A) and (B)
| Engine speed - Turbine speed (NE - NT) | 70 rpm or more |
| Turbine speed / Output speed (NT / NO) | Less than 3.30 or more than 7.50 |
2 detections are necessary per driving cycle:
1st detection: temporary flag ON
2nd detection: pending fault code ON
Vehicle speed must be under 10 km/h (6.2 mph) once before 2nd detection.
| Engine speed - Turbine speed (NE - NT) | Less than 35 rpm |
| Speed sensor (NT) | Input speed is equal to engine speed when lock-up ON. |
Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SLU operation.
[Vehicle Condition] ·
Throttle valve opening angle: Less than 35% ·
Vehicle speed: 80 km/h (50 mph) or more |
This test can be conducted when the vehicle speed is 80 km/h (50 mph) or more.
Perform this test while driving in 5th or 6th gear.
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
When changing the accelerator pedal opening angle while driving, if the engine speed does not change rapidly, lock-up is on.
Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
|---|---|
| Only P2757 is output | A |
| P2757 and other DTCs are output | B |
If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.
A
B
Remove shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| *a | Component without harness connected
(Shift Solenoid Valve SLU) |
OK
NG
OK
NG
OK
(See pageDrivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL)
NG
(See pageDrivetrain>A760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL)