Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234192 AUTOMATIC TRANSMISSION SYSTEM C

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0748  Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0748 The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear (1-trip detection logic).
Output signal duty equals 100%.
HINT:

SL1 output signal duty is less than 100% under normal conditions.


·

Open or short in shift solenoid valve SL1 circuit

·

Shift solenoid valve SL1

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the open or short-circuited solenoid.

While driving and shifting between 4th and 5th gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines that there is a malfunction (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

MONITOR STRATEGY

Related DTCs P0748: Shift solenoid valve SL1/Range check
Required sensors/Components Shift solenoid valve SL1
Frequency of operation Continuous
Duration 1 second
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present None
Solenoid current cut status Not cut
Battery voltage 11 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Solenoid status from solenoid driver MIC Fail

COMPONENT OPERATING RANGE

Output signal duty Less than 100%

WIRING DIAGRAM

C161203E83
2.791,1.287 3.021,1.457 0.230,0.170 10 16 5.476,1.287 5.706,1.457 0.230,0.170 10 14 2.321,1.066 2.743,1.261 0.422,0.195 10 SL1+ 2.791,2.502 3.021,2.672 0.230,0.170 10 5 2.321,2.283 2.743,2.479 0.422,0.195 10 SL1- 5.782,1.181 6.204,1.377 0.422,0.195 10 SL1+ 5.476,2.502 5.706,2.672 0.230,0.170 10 15 5.782,2.401 6.204,2.596 0.422,0.195 10 SL1- 0.973,2.891 1.395,3.086 0.422,0.195 10 D83 0.973,3.069 2.812,3.265 1.839,0.195 10 Transmission Wire 1.037,1.76 2.688,1.989 1.651,0.229 10 Shift Solenoid Valve SL1 5.96,3.223 6.301,3.393 0.341,0.170 10 D74 5.96,3.376 6.383,3.571 0.422,0.195 10 ECM 0.814,1.371 1.043,1.541 0.230,0.170 10 1 0.814,2.157 1.043,2.327 0.230,0.170 10 2

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>A760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


HINT:

The shift solenoid valve SL1 turns ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL1 OFF OFF OFF OFF ON ON


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)
a.
C210154E14
0.057,0.005 0.373,0.206 0.317,0.202 10 *a 2.033,1.819 2.430,2.021 0.398,0.202 10 SL1- 2.156,1.794 1.846,1.155 false 1.339,1.819 1.739,2.021 0.400,0.202 10 SL1+ 1.585,1.794 1.792,1.367 false

Disconnect the D83 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (SL1+) - 5 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
16 (SL1+) - Body ground Always 10 kΩ or higher
5 (SL1-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL1
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U152394E02
2.083,1.802 1.708,0.854 true 1.26,1.802 1.635,0.854 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.604,0.292 1.979,0.521 0.375,0.229 10 false D74 0.854,1.844 1.51,2.042 0.656,0.198 10 false 14 (SL1+) 1.833,1.823 2.542,2.021 0.708,0.198 10 false 15 (SL1-)

Disconnect the D74 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-14 (SL1+) - D74-15 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
D74-14 (SL1+) - Body ground Always 10 kΩ or higher
D74-15 (SL1-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL1
a.
C197715E31
1.74,0.99 2.208,0.365 false 1.49,0.99 1.052,0.365 false 1.75,2.958 2.208,2.354 false 1.49,2.958 1.052,2.354 false 0.052,0.01 0.365,0.208 0.313,0.198 10 false *a 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)

Remove shift solenoid valve SL1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SL1)


OK

NG