Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27M0U _55 Steering _049129 STEERING COLUMN _0234195 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the CPU based on that tilt.

C152160E12
0.979,0.104 2.188,0.448 1.208,0.344 10 false Tilt Up Mechanical Lock Position 4.865,0.104 6.375,0.521 1.51,0.417 10 false Tilt Down Mechanical Lock Position 2.958,1.854 4.104,2.052 1.146,0.198 10 false Operation Range 1.115,2.031 2.427,2.302 1.313,0.271 10 false Tilt Up Limit Position 4.573,2.021 6.135,2.271 1.563,0.25 10 false Tilt Down Limit Position

HINT:

Limit positions can be confirmed on the screen of the Techstream.


DTC Code Detection Condition Trouble Area
B2610 Tilt operation stops within the operation range while operating.
·

Harness or connector

·

Tilt position sensor or tilt motor

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C160342E03
0.792,4.177 1.104,4.375 0.313,0.198 10 false J48 0.906,1.021 1.635,1.229 0.729,0.208 10 false Tilt Motor 1.708,0.927 2.146,1.125 0.438,0.198 10 false TIM+ 1.708,1.719 2.146,1.917 0.438,0.198 10 false TIM- 4.656,1.708 5.031,1.906 0.375,0.198 10 false TIM- 1.771,2.469 2.094,2.667 0.323,0.198 10 false VCI 4.656,2.469 4.979,2.667 0.323,0.198 10 false VCI 1.771,2.865 2.052,3.063 0.281,0.198 10 false TIS 4.656,2.854 4.938,3.052 0.281,0.198 10 false TIS 1.813,3.26 2.063,3.458 0.25,0.198 10 false E1 4.656,3.24 4.906,3.438 0.25,0.198 10 false E1 0.479,3.365 1.771,3.583 1.292,0.219 10 false Tilt Position Sensor 2.094,1.729 2.24,1.927 0.146,0.198 10 false 1 4.458,1.719 4.604,1.917 0.146,0.198 10 false 1 2.104,0.927 2.229,1.125 0.125,0.198 10 false 2 2.104,2.469 2.25,2.667 0.146,0.198 10 false 4 2.104,2.865 2.25,3.063 0.146,0.198 10 false 5 2.104,3.26 2.219,3.469 0.115,0.208 10 false 6 4.448,2.479 4.563,2.688 0.115,0.208 10 false 6 4.448,2.865 4.563,3.073 0.115,0.208 10 false 7 4.646,4 4.979,4.198 0.333,0.198 10 false J47 4.396,0.917 4.635,1.115 0.24,0.198 10 false 10 4.396,3.646 4.635,3.844 0.24,0.198 10 false 11 4.385,3.24 4.625,3.438 0.24,0.198 10 false 17 4.646,3.646 5.052,3.844 0.406,0.198 10 false GND 5.969,0.594 6.281,0.792 0.313,0.198 10 false +B 5.979,1.417 6.292,1.615 0.313,0.198 10 false +B 6.083,2.156 6.49,2.354 0.406,0.198 10 false 12 V 6.052,3.271 6.417,3.469 0.365,0.198 10 false CPU 4.646,4.198 6.792,4.396 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.792,4.385 1.521,4.583 0.729,0.198 10 false Tilt Motor 4.635,0.927 5.031,1.125 0.396,0.198 10 false TIM+

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TILT UP/DOWN)
C106468E01
1.992,0.035 2.232,0.236 0.239,0.201 10 Up 2.474,1.152 2.886,1.363 0.413,0.211 10 Down

a.

Select the Active Test, use the Techstream to generate a control command, and then check that the steering wheel tilt up and down.

Tilt & Telescopic
Tester Display Test Part Control Range Diagnostic Note
Tilt operation Tilt operation Up / Down -

Result
Result Proceed to
Steering wheel does not tilt up (down). A
Steering wheel tilts up (down). B



A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

B

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
C352876E01
1.948,1.031 2.323,1.24 0.375,0.208 3.844,2.135 4.219,2.344 0.375,0.208 4.094,1.771 4.438,2.115 false 1.5,2.24 1.885,2.073 false 1.677,2.427 1.906,2.146 false 4.698,2.135 4.958,2.51 false 2.021,1.052 2.354,1.25 0.333,0.198 10 false J47 3.906,2.156 4.24,2.354 0.333,0.198 10 false J48 0.5,0.167 2.813,0.563 2.313,0.396 10 false Rear view of wire harness connector:(to Multiplex Tilt and Telescopic ECU) 3.875,0.208 6.188,0.604 2.313,0.396 10 false Rear view of wire harness connector:(to Tilt Motor) 1.177,2.167 1.573,2.365 0.396,0.198 10 false TIM+ 1.427,2.417 1.823,2.615 0.396,0.198 10 false TIM- 3.75,1.646 4.146,1.844 0.396,0.198 10 false TIM+ 4.906,2.542 5.302,2.74 0.396,0.198 10 false TIM-

a.

Disconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Disconnect the J48 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J47-10 (TIM+) - J48-2 (TIM+) Always Below 1 Ω
J47-1 (TIM-) - J48-1 (TIM-) Always Below 1 Ω
J47-10 (TIM+) - Body ground Always 10 kΩ or higher
J47-1 (TIM-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TILT MOTOR
C149090E08
1.542,1.135 1.094,1.25 false 2.177,1.125 2.49,0.969 false 5.521,1.115 5.885,0.969 false 4.896,1.135 4.396,1.271 false 0.604,0.063 3.094,0.458 2.49,0.396 10 false Component without harness connected: (Tilt Motor) 0.521,1.167 1.229,1.365 0.708,0.198 10 false TIM+ (+) 2.552,0.896 3.188,1.094 0.635,0.198 10 false TIM- (-) 4.042,0.073 6.531,0.469 2.49,0.396 10 false Component without harness connected: (Tilt Motor) 3.875,1.188 4.49,1.385 0.615,0.198 10 false TIM+ (-) 5.938,0.885 6.573,1.083 0.635,0.198 10 false TIM- (+)

a.

Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

OK
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal 2 (TIM+)
12 V battery negative (-) lead → Terminal 1 (TIM-)
The steering wheel tilts up.
12 V battery positive (+) lead → Terminal 1 (TIM-)
12 V battery negative (-) lead → Terminal 2 (TIM+)
The steering wheel tilts down.



OK

NG

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
C352929E01
2.063,1.042 2.438,1.26 0.375,0.219 3.875,2.052 4.25,2.271 0.375,0.219 2.313,2.063 2.615,1.979 false 2.24,2.125 2.688,2.219 false 2.198,2.125 2.51,2.51 false 4.135,2.417 4.427,2.229 false 4.406,2.521 4.531,2.229 false 4.635,2.229 4.844,2.469 false 0.563,0.198 2.854,0.604 2.292,0.406 10 false Rear view of wire harness connector:(to Multiplex Tilt and Telescopic ECU) 4.01,0.25 6.302,0.625 2.292,0.375 10 false Rear view of wire harness connector:(to Tilt Motor) 2.125,1.073 2.458,1.281 0.333,0.208 10 false J47 3.938,2.083 4.271,2.292 0.333,0.208 10 false J48 2.688,1.885 2.938,2.083 0.25,0.198 10 false E1 2.76,2.125 3.083,2.323 0.323,0.198 10 false TIS 2.427,2.531 2.75,2.729 0.323,0.198 10 false VCI 3.938,2.375 4.188,2.573 0.25,0.198 10 false E1 4.26,2.563 4.583,2.76 0.323,0.198 10 false TIS 4.781,2.5 5.104,2.698 0.323,0.198 10 false VCI

a.

Disconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Disconnect the J48 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J47-6 (VCI) - J48-4 (VCI) Always Below 1 Ω
J47-7 (TIS) - J48-5 (TIS) Always Below 1 Ω
J47-17 (E1) - J48-6 (E1) Always Below 1 Ω
J47-6 (VCI) - Body ground Always 10 kΩ or higher
J47-7 (TIS) - Body ground Always 10 kΩ or higher
J47-17 (E1) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C352931E01
1.906,1.26 2.25,1.479 0.344,0.219 1.438,2.958 1.844,2.615 false 0.188,0.146 2.5,0.563 2.313,0.417 10 false Rear view of wire harness connector:(to Multiplex Tilt and Telescopic ECU) 1.969,1.281 2.281,1.479 0.313,0.198 10 false J47 1.24,3 1.698,3.198 0.458,0.198 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J47-11 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)
a.
U152141E02
0.792,2.531 0.406,2.802 false 0.958,2.552 0.552,3.094 false 1.146,2.563 1.469,3.052 false 0.073,0 2.469,0.396 2.396,0.396 10 false Rear view of wire harness connector: (to Tilt Motor) 0.219,2.188 0.5,2.385 0.281,0.198 10 false J48 1.448,3.063 1.771,3.26 0.323,0.198 10 false VCI 0.469,3.104 0.771,3.302 0.302,0.198 10 false TIS 0.219,2.74 0.469,2.938 0.25,0.198 10 false E1

Reconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J48-4 (VCI) - J48-6 (E1) Ignition switch ON 8 to 16 V
J48-5 (TIS) - J48-6 (E1) Ignition switch ON 8 to 16 V




OK

7.CHECK TILT POSITION SENSOR

NG

7.CHECK TILT POSITION SENSOR
a.
C352932E01
1.948,1.417 2.302,1.625 0.354,0.208 2.354,1.958 2.583,1.615 false 2.813,2.521 2.292,2.083 false 0.115,0.125 2.521,0.521 2.406,0.396 10 false Component with harness connected:(Multiplex Tilt and Telescopic ECU) 2.01,1.438 2.323,1.635 0.313,0.198 10 false J47 2.635,1.51 2.948,1.708 0.313,0.198 10 false E1 2.875,2.469 3.229,2.667 0.354,0.198 10 false TIS

Reconnect the J48 tilt motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J47-7 (TIS) - J47-17 (E1) Steering tilts up or tilts down Pulse generation
High: 8 to 16 V
Low: Below 1 V




OK

NG