Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27M0U _55 Steering _049129 STEERING COLUMN _0234195 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2603  Tilt and Telescopic Manual Switch Circuit Malfunction  


DESCRIPTION

Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic manual switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.

DTC Code Detection Condition Trouble Area
B2603 When operating the tilt and telescopic manual switch, abnormal voltage value is input to the multiplex tilt and telescopic ECU.
·

Tilt and telescopic manual switch

·

Tilt and telescopic manual switch circuit

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C159015E04
5.832,3.836 6.939,4.149 1.107,0.313 10 Multiplex Tilt and Telescopic ECU 0.387,3.824 2.691,4.017 2.304,0.193 10 Headlight Dimmer Switch 0.595,3.243 2.718,3.403 2.123,0.161 10 Tilt and Telescopic Manual Switch 4.604,1.136 4.973,1.291 0.368,0.154 10 MSW 4.707,2.072 4.927,2.228 0.220,0.156 10 VC 6.074,1.24 6.442,1.394 0.368,0.154 10 MSW 6.093,2.195 6.313,2.352 0.220,0.156 10 VC 3.478,1.673 3.883,1.865 0.405,0.192 10 Long 2.582,1.673 2.867,1.865 0.285,0.192 10 Up 1.722,1.673 2.128,1.865 0.405,0.192 10 Short 0.836,1.673 1.241,1.865 0.405,0.192 10 Down 0.887,2.356 1.508,2.503 0.621,0.147 10 Tilt Down 1.761,2.356 2.443,2.673 0.682,0.317 10 Telescopic Contract 2.748,2.377 3.171,2.529 0.423,0.152 10 Tilt Up 3.506,2.356 4.194,2.704 0.687,0.348 10 Telescopic Extend 5.07,1.09 5.245,1.255 0.174,0.165 10 10 5.11,2.069 5.284,2.234 0.174,0.165 10 8 5.813,2.069 5.987,2.234 0.174,0.165 10 4 5.809,1.09 5.983,1.255 0.174,0.165 10 3 5.832,3.675 6.136,3.850 0.304,0.174 10 J47 0.387,3.661 0.691,3.836 0.304,0.174 10 J10

PROCEDURE

1.READ VALUE USING TECHSTREAM (TILT AND TELESCOPIC MANUAL SWITCH)
C113518E01
0.801,0.003 1.254,0.200 0.452,0.198 10 Tilt Up 1.907,1.618 2.591,1.816 0.684,0.198 10 Tilt Down 2.343,0.24 3.045,0.760 0.702,0.519 10 Telescopic Extend (Long) 0.143,0.802 0.845,1.321 0.702,0.519 10 Telescopic Contract (Short)

a.

Use the Data List to check if the tilt and telescopic manual switch is functioning properly.

Tilt & Telescopic
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
T&T Manual SW Data Voltage data of manual switch/min.: 0.00 V, max.: 4.99 V Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-

Result
Result Proceed to
Switch voltages in all directions are outside the standard. A
Switch voltages in certain directions are outside the standard. B
Switch voltages in all directions are within the standard. C



A

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH)

B

REPLACE HEADLIGHT DIMMER SWITCH

C

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH)
U152221E02
2.927,1.563 2.583,1.917 false 2.292,1.979 2.885,2.229 false 4.25,1.594 4.885,1.854 false 5.01,1.906 4.24,2.208 false 4.083,0.25 6.448,0.719 2.365,0.469 10 false Front view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 2.979,1.469 3.344,1.667 0.365,0.198 10 false MSW 3.885,1.5 4.281,1.698 0.396,0.198 10 false MSW 2.927,2.156 3.24,2.354 0.313,0.198 10 false VC 4.021,2.135 4.292,2.333 0.271,0.198 10 false VC 6.146,1.833 6.458,2.031 0.313,0.198 10 false J47 0.656,1.823 0.948,2.021 0.292,0.198 10 false J10 0.781,0.25 3.104,0.708 2.323,0.458 10 false Front view of wire harness connector: (to Headlight Dimmer Switch)

a.

Disconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Disconnect the J10 headlight dimmer switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J47-4 (VC) - J10-8 (VC) Always Below 1 Ω
J47-3 (MSW) - J10-10 (MSW) Always Below 1 Ω
J10-8 (VC) - Body ground Always 10 kΩ or higher
J10-10 (MSW) - Body ground Always 10 kΩ or higher




OK

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a.
C352997E01
1.906,1.313 2.271,1.563 0.365,0.25 2.146,2.063 2.563,1.646 false 2.063,2.104 2.719,2.521 false 0.104,0.094 2.375,0.521 2.271,0.427 10 false Component with harness connected:(Multiplex Tilt and Telescopic ECU) 1.958,1.344 2.281,1.531 0.323,0.188 10 false J47 2.635,1.521 2.865,1.719 0.229,0.198 10 false VC 2.875,2.552 3.104,2.75 0.229,0.198 10 false VC

Reconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J47-4 (VC) - J47-3 (MSW) Ignition switch ON 4.9 to 5.1 V




OK

4.INSPECT HEADLIGHT DIMMER SWITCH (TILT AND TELESCOPIC MANUAL SWITCH)

NG

4.INSPECT HEADLIGHT DIMMER SWITCH (TILT AND TELESCOPIC MANUAL SWITCH)
a.
C160341E05
0.448,2.875 0.927,2.26 false 1.688,2.917 1.271,2.271 false 0.146,0.052 2.677,0.427 2.531,0.375 10 false Component without harness connected: (Headlight Dimmer Switch) 1.635,2.938 1.927,3.188 0.292,0.25 10 false VC 0.26,2.906 0.719,3.146 0.458,0.24 10 false MSW

Disconnect the J10 headlight dimmer switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (VC) - 10 (MSW) Tilt up 342 to 378 Ω
Tilt down 1890.5 to 2089.5 Ω
Telescopic contract 750.5 to 829.5 Ω
Telescopic extend 152 to 168 Ω




OK

NG

REPLACE HEADLIGHT DIMMER SWITCH